| Visit Our Catalog at SteelGuitarShopper.com |

Post new topic Electric String Winder?
Reply to topic
Author Topic:  Electric String Winder?
Niels Andrews


From:
Salinas, California, USA
Post  Posted 13 Jun 2012 9:16 am    
Reply with quote

First time I saw this I thought it was a joke. I can't believe anyone would need a electric tool to change guitar strings. I have used EB crank for years and it is borderline overkill. I must be doing something wrong, but all my guitars with quality tuners stay in tune fine? Question
_________________
Die with Memories. Not Dreams.
Good Stuff like Zum S-12, Wolfe Resoport
MSA SS-12, Telonics Combo.
View user's profile Send private message Send e-mail
Richard Sinkler


From:
aka: Rusty Strings -- Missoula, Montana
Post  Posted 13 Jun 2012 9:45 am    
Reply with quote

I have used a Black & Decker electric screw driver at times when changing all the strings on my guitar. Saves a lot of time and wear and tear on my arm that has some problems. But mostly I just use a manual winder.

Whether you wind your strings with an electric or manual winder (or just your fingers) has no effect on whether your strings stay in tune.
_________________
Carter D10 8p/8k, Dekley S10 3p/4k C6 setup,Regal RD40 Dobro, Recording King Professional Dobro, NV400, NV112,Ibanez Gio guitar, Epiphone SG Special (open D slide guitar) . Playing for 54 years and still counting.
View user's profile Send private message Send e-mail
David Nugent

 

From:
Gum Spring, Va.
Post  Posted 13 Jun 2012 10:36 am    
Reply with quote

I own one of these Ernie Ball gizmos and would not be without it, cuts string changing time on a steel guitar in half...(FWIW)..Have read a few negative reviews stating that these will quit working after a short period of use, not so. Due to a minor design flaw, there is excess space in the battery compartment and the batteries rattle around and lose contact with the poles. I placed a small section of cardboard in mine and have had no problem since.
View user's profile Send private message
Erv Niehaus


From:
Litchfield, MN, USA
Post  Posted 13 Jun 2012 11:45 am    
Reply with quote

Stick 'em up! Whoa!

View user's profile Send private message Send e-mail
Niels Andrews


From:
Salinas, California, USA
Post  Posted 13 Jun 2012 12:42 pm    
Reply with quote

Right Erv, the point I was making is you don't need two feet of extra string, a couple of turns and the string won't slip.
_________________
Die with Memories. Not Dreams.
Good Stuff like Zum S-12, Wolfe Resoport
MSA SS-12, Telonics Combo.
View user's profile Send private message Send e-mail
Erv Niehaus


From:
Litchfield, MN, USA
Post  Posted 13 Jun 2012 12:59 pm    
Reply with quote

Niels,
I don't have one either but sometimes it would come in handy especially when stringing up something like this:


View user's profile Send private message Send e-mail
Niels Andrews


From:
Salinas, California, USA
Post  Posted 13 Jun 2012 1:36 pm    
Reply with quote

Thanks Erv,
After looking at that thing I will have nightmares.The question is why would one endure such punishment? Music should be pleasurable. Laughing
_________________
Die with Memories. Not Dreams.
Good Stuff like Zum S-12, Wolfe Resoport
MSA SS-12, Telonics Combo.
View user's profile Send private message Send e-mail
Lynn Fargo


From:
Fort Edward, NY
Post  Posted 13 Jun 2012 1:38 pm    
Reply with quote

Funny, I just ordered mine about 30 mts ago from my local music store. I'm expecting my Live Steel Strings in the mail any day now, and wasn't looking forward to all that winding with the sidewinder. (Prone to tendonitis.) Hope I fall in love with both my new acquisitions.
_________________
Sho-Bud Pro II Custom, GFI Ultra SD-10, Fender Pro Amp, Fender Mustang II Amp, Morrell 8-string lap, Epiphone 6-string lap, Galveston reso, etc.
View user's profile Send private message Send e-mail
Lee Baucum


From:
McAllen, Texas (Extreme South) The Final Frontier
Post  Posted 13 Jun 2012 1:57 pm    
Reply with quote

I've got a couple of cordless string winders.
View user's profile Send private message Send e-mail
David Eastwood


From:
Minnesota, USA
Post  Posted 13 Jun 2012 2:23 pm    
Reply with quote

I've had one of the EB winders for a couple of years now. I find it almost makes string changing a pleasure (I did say 'almost').

I would, however, recommend verifying exactly which way it needs to turn *before* applying it to the tuner Smile
View user's profile Send private message Send e-mail
Bill Moran

 

From:
Virginia, USA
Post  Posted 15 Jun 2012 10:29 am    
Reply with quote

Been using a Black & Decker cordless screwdriver for 25 years. LOL. Just lazy I guess. Very Happy
_________________
Bill
View user's profile Send private message Send e-mail
Lee Baucum


From:
McAllen, Texas (Extreme South) The Final Frontier
Post  Posted 15 Jun 2012 2:31 pm    
Reply with quote

Bill - I've got a pretty large collection of cordless screwdrivers hanging on the pegboard out in my garage! Razz
View user's profile Send private message Send e-mail
Tony Glassman


From:
The Great Northwest
Post  Posted 15 Jun 2012 3:06 pm    
Reply with quote

I use a cordless variable speed screwdriver. It makes a tedious task quicker and easier.

I have the guitar plugged into a tuner, and rapidly tighten'em to within a whole tone of the target note.
Then I slowly advance til I overshoot by a half-tone. Saves on having to manually stretch them.

I can't see the downside of using one.
View user's profile Send private message
Ray Montee


From:
Portland, Oregon (deceased)
Post  Posted 15 Jun 2012 3:52 pm     I'm gettin' depressed!
Reply with quote

I just calculated how many strings I have to change and it totals 167 strings. Whew! That's $127.00 worth of 'new strangs' to reinstall.

Do you guys simply cut the strings when you're in the process of removing them or what?

If yes, how do you get the short ends still wrapped around the tuning device off the guitar in the process?

I'm gettin' more depressed the more I ponder the question and await your next responses.
View user's profile Send private message Send e-mail Visit poster's website
Lane Gray


From:
Topeka, KS
Post  Posted 15 Jun 2012 4:48 pm    
Reply with quote

I used to use (til it broke) this cheap chinese cordless screwdriver that had an adjustable clutch. I set it to where it'd start slipping just shy of full tension at pitch.
I still miss that sucker.
_________________
2 pedal steels, a lapStrat, and an 8-string Dobro (and 3 ukes)
More amps than guitars, and not many effects
View user's profile Send private message Send e-mail Yahoo Messenger
Lee Baucum


From:
McAllen, Texas (Extreme South) The Final Frontier
Post  Posted 16 Jun 2012 8:47 am    
Reply with quote

One thing I like about my cordless string-winders and my collection of cordless screwdrivers is the fact that none of them require batteries.
View user's profile Send private message Send e-mail
Lane Gray


From:
Topeka, KS
Post  Posted 16 Jun 2012 9:07 am    
Reply with quote

I was just listening to Hiram King Williams.
A winder is what the light shines bright from.
_________________
2 pedal steels, a lapStrat, and an 8-string Dobro (and 3 ukes)
More amps than guitars, and not many effects
View user's profile Send private message Send e-mail Yahoo Messenger
Henry Matthews


From:
Texarkana, Ark USA
Post  Posted 16 Jun 2012 8:59 pm    
Reply with quote

All my string winders are cordless, never seen one with a cord. Smile
_________________
Henry Matthews

D-10 Magnum, 8 &5, dark rose color
D-10 1974 Emmons cut tail, fat back,rosewood, 8&5
Nashville 112 amp, Fishman Loudbox Performer amp, Hilton pedal, Goodrich pedal,BJS bar, Kyser picks, Live steel Strings. No effects, doodads or stomp boxes.
View user's profile Send private message Send e-mail
Tony Glassman


From:
The Great Northwest
Post  Posted 16 Jun 2012 9:27 pm     Re: I'm gettin' depressed!
Reply with quote

Ray Montee wrote:
......

Do you guys simply cut the strings when you're in the process of removing them or what?

If yes, how do you get the short ends still wrapped around the tuning device off the guitar in the process?



Ray, I put a cloth over the strings and cut'em in the middle (the cloth protects my hand, and stops the ball end remnants from flying off). Then I collect the changer end portions and toss them.

After that, I grab the key head string end with my left hand and unwind it off the key using a cordless driver in my right. De-stringing a D-10 takes about 5 minutes.

To restring, I measure and cut the string about two tuning posts longer than needed. After poking the string through the tuner. I bend it at a right angle, give the key a couple of turns (to lock it) and then hook the ball end on the changer. Maintaining string tension, I reach over and tighten the key-head til it's a half tone over open pitch. The most important thing is to make sure the ball end is snug up against the changer pin, so it doesn't get sheared off.
View user's profile Send private message
Ken Metcalf


From:
San Antonio Texas USA
Post  Posted 18 Jun 2012 5:33 am    
Reply with quote

I use a cordless screw gun and have thought of getting a fancier one, its nice.
I put a couple extra wraps on my 3rd string.
_________________
MSA 12 String E9th/B6th Universal.
Little Walter PF-89.
Bunch of stomp boxes
View user's profile Send private message Send e-mail
David Nugent

 

From:
Gum Spring, Va.
Post  Posted 18 Jun 2012 6:57 am    
Reply with quote

I use the exact method as Tony (two posts past the intended tuning key) to pre-cut my plain strings, but it should be noted that on the wound strings, as the gauge size increases it will be necessary to decrease the string length so that there is sufficient space to wind the string on the post.
View user's profile Send private message
Sonny Jenkins


From:
Texas Masonic Retirement Center,,,Arlington Tx
Post  Posted 18 Jun 2012 11:18 am    
Reply with quote

,,,,jeeeezzz,,,and I've heard guys criticize keyless guitars because you have to have an allen wrench to change strings,,,,,hello-o-o-o
View user's profile Send private message Send e-mail

All times are GMT - 8 Hours
Jump to:  
Please review our Forum Rules and Policies
Our Online Catalog
Strings, CDs, instruction, and steel guitar accessories
www.SteelGuitarShopper.com

The Steel Guitar Forum
148 S. Cloverdale Blvd.
Cloverdale, CA 95425 USA

Click Here to Send a Donation

Email SteelGuitarForum@gmail.com for technical support.


BIAB Styles
Ray Price Shuffles for Band-in-a-Box
by Jim Baron