| Visit Our Catalog at SteelGuitarShopper.com |

Post new topic ShoBud Amp
Reply to topic
Author Topic:  ShoBud Amp
Carl Dvorcek

 

From:
Texas, USA
Post  Posted 28 Aug 2002 1:00 pm    
Reply with quote

I just picked up a Shobud Amplifier. The label on the back says Model 7832, manufactured by Baldwin Piano Co.. It's a two channel "Twin Transistor". It has eleven side potentiometers on the front and a power meter on the right side. I'm assuming it's from the late 60's to early 70's. Can anyone tell me anything about this amp? I may also need a schematic and parts if someone can lead me in the right direction.
It works but has a hum. If I turn the reverb off, the hum goes away. Also, you can only play notes/chords in upper frequency ranges. Low frequencies make it sound like a Mack truck in low gear. Breaks up real bad.

Thanks,
Carl
View user's profile Send private message Send e-mail
Bob Lawrence


From:
Beaver Bank, Nova Scotia, Canada
Post  Posted 28 Aug 2002 1:33 pm    
Reply with quote

Carl,

Jimmy Campbell worked for Sho-Bud in Nashville from 73-76 (in the good old days). He has schematics for Single Channel and Dual Channel Sho-Bud amps. You can use the link below to send him a e-mail. He put a set in the mail for me a few days ago.
http://steelguitarforum.com/Forum11/HTML/002722.html


Bob


------------------
View user's profile Send private message Send e-mail
Carl Dvorcek

 

From:
Texas, USA
Post  Posted 29 Aug 2002 5:28 pm    
Reply with quote

Thanks Bob. Just talked to Jimmy a few moments ago and he's sending me a schematic.

Carl Smile
View user's profile Send private message Send e-mail
Bob Lawrence


From:
Beaver Bank, Nova Scotia, Canada
Post  Posted 8 Sep 2002 5:15 am    
Reply with quote

Carl,

I just got mine in the mail on Friday. Looks great. He also e-mailed a very nice picture of it.

Bob


------------------

[This message was edited by Bob Lawrence on 08 September 2002 at 06:16 AM.]

View user's profile Send private message Send e-mail
Carl Dvorcek

 

From:
Texas, USA
Post  Posted 8 Sep 2002 6:36 am    
Reply with quote

I got mine Monday. Unfortunately, it wasn't the one for my amp. I'm still searching. However, I did establish a nice rapport with Jimmy. Thanks for the reply.

Carl
View user's profile Send private message Send e-mail
Bob Metzger

 

From:
Waltham (Boston), MA, USA
Post  Posted 14 Sep 2002 9:46 am    
Reply with quote

Do a cap job on it and if it's a spring reverb/tank operation, check the shielding on the wires to and from the reverb tank.

These amp generally need new filter caps for rock solid bass performance, if they still have the original units. Although I have a different model Sho-Bud amp than yours, I think my B+ filter caps are 5000uf@63 volts. The value is usually printed on the can. 4700uf, which today is a more commonly seen value, will work in an almost indistingushable manner. This will get you started, but I'd also replace all electrolytic caps in the amp and there are alot of ceramic caps that could be upgraded to better sounding devices. Replace all drifted resistor as well. Certainly, replace all that are 10% from stated value and some critical ones should be 2%. This will remove that 'tired, worn out' sound from the amp.

Bob M.
View user's profile Send private message Send e-mail
chas smith R.I.P.


From:
Encino, CA, USA
Post  Posted 14 Sep 2002 10:48 am    
Reply with quote

Jimmy sent me some copies and wouldn't take anything in return. I feel a little awkward about getting something for nothing, so let me sing his praises, what a wonderful person he is.
View user's profile Send private message
Carl Dvorcek

 

From:
Texas, USA
Post  Posted 15 Sep 2002 3:34 am    
Reply with quote

Thanks for the reply Bob. The B+ caps are 4000uf @ 60 V. I have found a few transistors (SFC5865, 7223A) that are bad. I still need to find a suitable cross for them. I believe they may correct the reverb problem and the lack of signal to the ammeter. I also found and corrected countless cold solder joints. The electrolytics on the board have already been replaced. B+ caps are next because they have visible evidence of leakage. Once I get all that cleared up, I have some slide potentiometers to replace. That's going to be the tough one. Haven't been able to find any that aren't PCB mount. The pots on this amp attach to a metal plate with tabs on the back of the pot. I may have to reverse engineer. I may have failed to mention that it has a sweet JBL K-130 in it. Even if the amp was a loss, the speaker was worth the investment.

r,
Carl
View user's profile Send private message Send e-mail
Jerry Roller


From:
Van Buren, Arkansas USA
Post  Posted 15 Sep 2002 7:31 am    
Reply with quote

Does anyone know where to get the slide controls? I have one of these amps and all the sliders are broken off even with the face.
Jerry
View user's profile Send private message Visit poster's website
Carl Dvorcek

 

From:
Texas, USA
Post  Posted 15 Sep 2002 5:56 pm    
Reply with quote

Jerry: I've searched high and low without any luck, so far. I thought about shortening the standoffs that the mounting plate attaches to. That would allow the broken slides to protrude through the face of the amp, hopefully enough to get some knobs on them. If nothing else, they'd be accessible.

r,
Carl
View user's profile Send private message Send e-mail
Herb Steiner

 

From:
Spicewood TX 78669
Post  Posted 15 Sep 2002 5:59 pm    
Reply with quote

Or, could you fabricate a new face plate and have regular radial pot controls installed?

This model ShoBud amp was subject to this design flaw, historically.

------------------
Herb's Steel Guitar Pages
Texas Steel Guitar Association

View user's profile Send private message Send e-mail Visit poster's website
Carl Dvorcek

 

From:
Texas, USA
Post  Posted 16 Sep 2002 11:01 am    
Reply with quote

Jerry: My amp also had all slides broken off flush with the face. However, I tried my idea about shortening the standoffs. It works beautifully. There's more than ample amount of slide coming through the face of the amp to add slide knobs. Now all I have to do is find some knobs that will fit the thickness of the slide. They're not standard because I've tried several new ones and they won't fit. At least I can control everything now.

r,
Carl
View user's profile Send private message Send e-mail
Jerry Roller


From:
Van Buren, Arkansas USA
Post  Posted 17 Sep 2002 8:02 pm    
Reply with quote

Great idea Carl, thanks, if I can come up with some slider knobs I'll let you know.
Jerry
View user's profile Send private message Visit poster's website

All times are GMT - 8 Hours
Jump to:  
Please review our Forum Rules and Policies
Our Online Catalog
Strings, CDs, instruction, and steel guitar accessories
www.SteelGuitarShopper.com

The Steel Guitar Forum
148 S. Cloverdale Blvd.
Cloverdale, CA 95425 USA

Click Here to Send a Donation

Email SteelGuitarForum@gmail.com for technical support.


BIAB Styles
Ray Price Shuffles for Band-in-a-Box
by Jim Baron