| Visit Our Catalog at SteelGuitarShopper.com |

Post new topic Fender Twin Reverb Tanks
Reply to topic
Author Topic:  Fender Twin Reverb Tanks
Frank Venters

 

From:
Peru,In,USA
Post  Posted 14 Nov 2000 9:06 am    
Reply with quote

I'm looking for information on the size(input and output/Ohms) for the Fender Twin Reverb Tanks. My twin is a 1971 model, with stock 12" Fender Speakers.I haven't taken mine out yet, but I believe it may be 8 ohmns input and about 2250 ohms output.Any ideas out there. One more question..."Can the springs in the reverb tank be adjusted"?
View user's profile Send private message
Jay Ganz


From:
Out Behind The Barn
Post  Posted 14 Nov 2000 9:51 am    
Reply with quote

Hey Frank,

On most of the standard tanks for Fenders,
I usually read maybe around a few ohms on the input & about 160 ohms on the output. Of course, that's reading resistance with a meter which is not actual impedance.
But it gives a general idea.
You can't adjust the springs, but you can
swap them with another tank if one is a bit
to "boingy"...if ya know what I mean.
They just unhook on either end, although
it's a bit tricky.

[This message was edited by Jay Ganz on 14 November 2000 at 03:05 PM.]

View user's profile Send private message Send e-mail Visit poster's website
Donny Hinson

 

From:
Glen Burnie, Md. U.S.A.
Post  Posted 14 Nov 2000 2:31 pm    
Reply with quote

If you remove your old one, it should have a part number rubberstamped on it. You can then go to the "Accutronics" website, and determine exactly what you have. You might also get an answer on the Fender Discussion Page at... http://www.fenderforum.com/
There's a wealth of good Fender info there!

Maybe one of the "electronically erudite" members here (like Jack Stoner) could tell us how critical those impedances really are. Since "Antique Electronics" has replacements for less than $20, I hardly think it's worth a lot of time and effort to try to repair one.

[This message was edited by Donny Hinson on 14 November 2000 at 02:45 PM.]

View user's profile Send private message Send e-mail
Jon Light


From:
Saugerties, NY
Post  Posted 14 Nov 2000 2:38 pm    
Reply with quote

Frank--maybe you can find your answer here--
http://www.accutronicsreverb.com/prodspec.htm

View user's profile Send private message Send e-mail Visit poster's website
Jack Stoner


From:
Kansas City, MO
Post  Posted 14 Nov 2000 3:57 pm    
Reply with quote

It's been a while since I worked on a Fender and C.R.S. has set in as far as what the impedence of that tank is. The suggestions to check with accutronics or antique electronics is the best bet.
View user's profile Send private message Send e-mail
Michael Brebes

 

From:
Northridge CA
Post  Posted 15 Nov 2000 5:30 am    
Reply with quote

You can also go to www.mojotone.com, which carries replacement reverb tanks. For Fender amps there are usually 4 reverb tanks available, a short tank with either two or three springs and a long tank (like in the Twin) with either two or three springs. The 3 spring versions should give a bit more complex reverb. The short tank will usually give a little shorter delay and decay times.
View user's profile Send private message Send e-mail

All times are GMT - 8 Hours
Jump to:  
Please review our Forum Rules and Policies
Our Online Catalog
Strings, CDs, instruction, and steel guitar accessories
www.SteelGuitarShopper.com

The Steel Guitar Forum
148 S. Cloverdale Blvd.
Cloverdale, CA 95425 USA

Click Here to Send a Donation

Email SteelGuitarForum@gmail.com for technical support.


BIAB Styles
Ray Price Shuffles for Band-in-a-Box
by Jim Baron