| Author |
Topic: In need of a few Shobud parts please can anyone help? |
John Davis
From:
Cambridge, U.K.
|
Posted 30 Nov 2024 7:45 am |
|
I have bought a Pro1, i think it must have been born just after the Rack and Rattle ones it has cross shafts and cranks but only two knee levers so, to finish the job i need 4 cranks and for of those brass adjusters.
I have made reverse lever but I am stuffed without the other bits, can you help me?
Best, John Davis |
|
|
 |
Dan Beller-McKenna
From:
Durham, New Hampshire, USA
|
Posted 30 Nov 2024 8:01 am
|
|
| Barry Coker here on the forum might be able to make those. Pretty sure Michal Yahl has those parts, but his site has been down for a bit |
|
|
|
K Maul
From:
Hadley, NY/Hobe Sound, FL
|
Posted 30 Nov 2024 8:58 am
|
|
Johnie King may have some. I just bought 3 locking pullers from him.
_________________
KEVIN MAUL: Airline, Beard, Clinesmith, Danelectro, Evans, Fender, GFI, Gibson, Hilton, Ibanez, Justice, K+K, Live Strings, MOYO, National, Oahu, Peterson, Quilter, Rickenbacher, Sho~Bud, Supro, TC, Ultimate, VHT, Williams, X-otic, Yamaha, ZKing. |
|
|
|
Barry Coker
From:
Bagley Alabama, USA
|
Posted 30 Nov 2024 4:33 pm
|
|
I have the cranks and brackets below:
Barry
_________________
Zum-D-10, Webb 614-E, 65 Pro Reverb, Evans RE200, 69 Gibson Birdland, 89 Telecaster EAD Bad!! |
|
|
|
Ricky Davis
From:
Bertram, Texas USA
|
Posted 30 Nov 2024 8:50 pm
|
|
No; these are the two-hole pullers with Brass rollers that John Davis is looking for:
They go on "round crossbar"; NOT HEX.
And yes check with that Johnie King dude; cause he buys and takes apart the back neck of D-10's and makes a SD-10 out of so many; including Sho-Bud; so he has a ton of parts he try's to sell; that nobody can really buy unless all the mechanics of their Double-10 just falls off for no reason...so he has got to have a ton of these pullers w/brass rollers.
Ricky
_________________
Ricky Davis
Email Ricky: sshawaiian2362@gmail.com |
|
|
|
John Davis
From:
Cambridge, U.K.
|
Posted 30 Nov 2024 10:05 pm
|
|
Thanks for the input you guys are the best and yes, Ricky is correct i also need 4 of the brass fine tuners that work with this design, thanks again for trying to help.
I sent mail to Johnnie King but it bounced back via admin don't know if he rec. It. |
|
|
|
Ricky Davis
From:
Bertram, Texas USA
|
Posted 1 Dec 2024 6:05 am
|
|
| Quote: |
| i also need 4 of the brass fine tuners that work with this design |
Yes John; here's what's called "Barrel Tuners" you are asking for 4 of them also.
You're mighty welcome and good luck.
Ricky
_________________
Ricky Davis
Email Ricky: sshawaiian2362@gmail.com |
|
|
|
John Davis
From:
Cambridge, U.K.
|
Posted 1 Dec 2024 7:52 am
|
|
Have found barrel tuners just need cranks now....
Would swap some emmons cranks for them. |
|
|
|
Ricky Davis
From:
Bertram, Texas USA
|
Posted 1 Dec 2024 8:09 am
|
|
| Quote: |
| Would swap some emmons cranks for them. |
Yes actually; you only need the Barrel Tuners on the fingers that raise the note TWICE;...like C pedal E to F# and lever that raises that E to F; one rod/two barrel tuners. Same with C pedal and A pedal raising the B to C# twice...all the other rods that have just a single raise or single lower; can be really any puller that fits on crossbar you use a rod with nylon tuner at endplate and can hook on used puller...yeeehaaaa..
Ricky
_________________
Ricky Davis
Email Ricky: sshawaiian2362@gmail.com |
|
|
|
John Davis
From:
Cambridge, U.K.
|
Posted 1 Dec 2024 12:29 pm
|
|
Well thats something I never thought of and the guitar will probably work better for it, easier than drilling
Out set screws to make those weird end bits
The only reservation it would have to be a tiny bit of nylon hex that would be sticking out of the end of the guitar |
|
|
|
Ricky Davis
From:
Bertram, Texas USA
|
Posted 1 Dec 2024 4:41 pm
|
|
| Quote: |
| Well that's something I never thought of and the guitar will probably work better for it |
Well that is exactly what Paul Franklin Sr. did to Lloyd Green's first LDG; as he got rid of all barrel tuners; but in order to keep the best sounding 6061 aluminum finger tops on the single/single Steel; he welded an extra raise hole on fingers 4 and 5 and all rods were then fixed to pullers with rollers with set screw and put 1/2" nylon hex tuners on his pulls...yeeehaaa.(you can put 3/16" hex nylon tuners and not have anything stick out; but the 1/2", you can see much better in sitting position to see which nylon you want to put tuner on...ha...
Ricky
_________________
Ricky Davis
Email Ricky: sshawaiian2362@gmail.com |
|
|
|
