| Visit Our Catalog at SteelGuitarShopper.com |

Post new topic Franklin Pull Rods
Reply to topic
Author Topic:  Franklin Pull Rods
Jeremy Moyers

 

From:
Lubbock, TX
Post  Posted 5 Apr 2024 11:25 am    
Reply with quote

Hello all,

I am needing to build a few new pull rods for my Franklin Guitar. I spoke with Paul Sr. several years ago about this and took detailed notes on what he said about the pull rods. He said that he used aircraft grade 1/8" aluminum rods. He made sure to say that he used full 1/8", 125/1000 aluminum rod and that it was aircraft grade, so I am assuming that these specs are important.

I have read on here that some people use 1/8" aluminum TIG welding rods as pull rods. I have used 4043 TIG welding rods in the past, but honestly they seem not to be nearly as rigid as the pull rods that came on the guitar from the factory. So, to my questions...

1). What is aircraft grade aluminum exactly? Is it 2024? 6061? As stated above, I have used 4043 welding rod in the past but have not been impressed by the durability of the product. From what I read 2024 is much more dense and stronger than other aluminums because it is also copper clad?

2) Do you know of a good source for 1/8" the aircraft grade aluminum rods?

I have the 1/16" roll pins that Paul Sr. used, and I have the #6-40 tap and die set, just trying to find the correct rods.

Thanks for the help!

Jeremy
View user's profile Send private message Send e-mail Visit poster's website
Johnie King


From:
Tennessee, USA
Post  Posted 6 Apr 2024 3:36 pm    
Reply with quote

The trick is drilling the small hole in the center of the 1/8 inch aluminum rod
For the 1//16 spring pin.
I’m sure Paul senior must have had a good jig for this .


View user's profile Send private message Send e-mail
Johnie King


From:
Tennessee, USA
Post  Posted 6 Apr 2024 3:48 pm    
Reply with quote

View user's profile Send private message Send e-mail
Bobby D. Jones

 

From:
West Virginia, USA
Post  Posted 6 Apr 2024 9:35 pm    
Reply with quote

Check length of rod when you order, Have it cut into 3 ft. lengths or less. Long objects have much higher shipping rate.

Make a jig out of a piece of heavy steel block. Drill 1/8" hole in 1 edge, Then drill 90 degree 1/16" hole perfect centered through 1/8" hole. Insert 1/8" rod in 1/8" and drill 1/16" hole through 1/16" jig hole. For perfect centered hole.
View user's profile Send private message Send e-mail
Tim Toberer


From:
Nebraska, USA
Post  Posted 7 Apr 2024 5:43 am    
Reply with quote

I read somewhere that you shouldn't use aluminum cause it expands and contracts. If Franklin uses them it must be fine. Maybe this alloy doesn't shrink as much? I have been using regular welding rod but would prefer aluminum cause it is lighter.
View user's profile Send private message Send e-mail
LaVern Skarzenski

 

From:
North East,Pennsylvania, USA
Post  Posted 7 Apr 2024 6:42 am     Source of 2024 Aluminum
Reply with quote

I believe Gene Fields too was concerned with expansion/contraction of aluminum, but If Paul Franklin says he used it, it obviously worked for him. Here is a source.

https://www.mcmaster.com/products/metals/aluminum~/tight-tolerance-high-strength-2024-aluminum-rods/

LaVern
_________________
GFI S10, BSG S10, Nashville 112, Digitech 155, DOD DFX9 Digital Delay, Goodrich L 120.
View user's profile Send private message Send e-mail
Patrick Timmins


From:
Seattle
Post  Posted 7 Apr 2024 1:28 pm    
Reply with quote

I make them pretty frequently in my shop. I also replace the aluminum with stainless steel so at least that one will not break in the future. You can also use a tighter nylon tuning nut on stainless rods than aluminum since the aluminum breaks so easy.
You can read this posting to see how I make them.
https://bb.steelguitarforum.com/viewtopic.php?t=388896&highlight=
_________________
Microphones, Recording, and lots of pedal steel guitars!
View user's profile Send private message Send e-mail Visit poster's website
Jerry Overstreet


From:
Louisville Ky
Post  Posted 7 Apr 2024 2:41 pm    
Reply with quote

I once owned an '81 Zum D10 that I believe had aluminum pull rods. Of course I defer to Bruce.

Definitely not ferrous metal, lighter than any type of steel.
The color had a dull finish...MOF, I still have one of them.

Never any problems with them.
View user's profile Send private message
Bobby D. Jones

 

From:
West Virginia, USA
Post  Posted 8 Apr 2024 7:11 pm    
Reply with quote

I have some 1/8" Aluminum pull rods, They are threaded 6-40 on 1 end, And have dings from where a setscrew had tightened into them. They was in a box of misc. parts that came from a guy that had the MSA Classic D10 that I bought.

I have changed out several copper coated rods out of steels, For Stainless Steel. They were mild steel welding rods with a copper coating, To keep them from rusting, Rusty welding rods don't make good welds.
View user's profile Send private message Send e-mail

All times are GMT - 8 Hours
Jump to:  
Please review our Forum Rules and Policies
Our Online Catalog
Strings, CDs, instruction, and steel guitar accessories
www.SteelGuitarShopper.com

The Steel Guitar Forum
148 S. Cloverdale Blvd.
Cloverdale, CA 95425 USA

Click Here to Send a Donation

Email SteelGuitarForum@gmail.com for technical support.


BIAB Styles
Ray Price Shuffles for Band-in-a-Box
by Jim Baron