Author |
Topic: Peavey NV 400 mods |
Charles Bell
From: Earlysville, VA
|
Posted 22 Jul 2024 10:43 am
|
|
Any sources for parts/install on the necessary mods for a black corner pre-mod NV 400? |
|
|
![](templates/respond/images/spacer.gif) |
Richard Sinkler
From: aka: Rusty Strings -- Missoula, Montana
|
Posted 22 Jul 2024 11:20 am
|
|
Even though this post is for a Nashville 112, the chips needed are the same.
https://bb.steelguitarforum.com/viewtopic.php?t=401916 _________________ Carter D10 8p/8k, Dekley S10 3p/4k C6 setup,Regal RD40 Dobro, Recording King Professional Dobro, NV400, NV112,Ibanez Gio guitar, Epiphone SG Special (open D slide guitar) . Playing for 54 years and still counting. |
|
|
![](templates/respond/images/spacer.gif) |
Bill Ferguson
From: Milton, FL USA
|
Posted 22 Jul 2024 1:22 pm
|
|
I may be wrong, but I believe that when Peavey changed to the black corners on the NV400, that was when they started installing the factory mod.
Of course, I could be wrong. I've definitely been wrong before. hehe _________________ AUTHORIZED George L's, Goodrich, Telonics and Peavey Dealer: I have 2 steels and several amps. My current rig of choice is 1993 Emmons LeGrande w/ 108 pups (Jack Strayhorn built for me), Goodrich OMNI Volume Pedal, George L's cables, Goodrich Baby Bloomer and Peavey Nashville 112. Can't get much sweeter. |
|
|
![](templates/respond/images/spacer.gif) |
Pat Chong
From: New Mexico, USA
|
Posted 23 Jul 2024 1:18 pm
|
|
Hi Charles,
I also have the PV 400 with the black corners, it needed the mod, so black corners may or may not apply.
It has been mentioned that there are 3 versions of this amp. Versions 1 and 3 did not need a modification, it's only version 2 that did.
Version 1 had a 1502-4 black widow speaker.
Version 3 had the Peavey mod installed on and after serial number 08575482.
So if your speaker is 1501-4 and your serial number is under 08575482, then a mod may be needed.
The sources I have used is Mouser Electronics, they have the parts/chips needed to mod your 400. If you are going to do this yourself, you MUST get the parts layout from Peavey, as the parts are not labeled on the board (C1, R17, etc.) and the instructions on what parts to replace/get from Mouser.
There is also a reverb mod still available from Bob Metzger (you can contact him, he's a member). It too, is a good addition.
Pat. |
|
|
![](templates/respond/images/spacer.gif) |
Richard Sinkler
From: aka: Rusty Strings -- Missoula, Montana
|
Posted 23 Jul 2024 3:19 pm
|
|
The Peavey mods happened after a certain serial number. _________________ Carter D10 8p/8k, Dekley S10 3p/4k C6 setup,Regal RD40 Dobro, Recording King Professional Dobro, NV400, NV112,Ibanez Gio guitar, Epiphone SG Special (open D slide guitar) . Playing for 54 years and still counting. |
|
|
![](templates/respond/images/spacer.gif) |
Ken Fox
From: Nashville GA USA
|
|
|
![](templates/respond/images/spacer.gif) |