GFI Ball end holder

Jack Stoner · From: Kansas City, MO

Anyone come up with something to temporarily hold the ball end in the changer when changing strings?

Last time my wife was the "holder". I curse every time I have to change strings on a GFI. I like GFI's but its taking me longer to change strings on my SD-10 than it did to change strings on both necks on the Franklin I had (has pins for ball end).

The strings I have on the guitar now are 8 months old and dead. Just playing at home but dead strings tone sucks.

Jerry Overstreet · From: Louisville Ky

Jack, I use a stick on pencil eraser like this:

I see some others here suggest a rubber piano tuner mute. I think these are about 3/16 of an inch wide. Your GFI doesn't appear like there's a lot of room between the roller finger and the housing though.

Also consider a plastic mini paint brush handle of the correct size, plastic chop stick etc.

Patrick Edwards · From: Port Orchard, Washington, USA

I use a plastic straw . The one I have now is a little large so I put a crease in it .
I used to just tear a string envelope in half , roll it up and use it like a straw.[img][/img]

Jack Stoner · From: Kansas City, MO

Jerry, wrong changer type. That is a pin type, like my Franklin.

Patrick, thanks, I had considered something like what you show.

Jerry Overstreet · From: Louisville Ky

Yes it is, but I use that for both designs. It depends on the gap you have between the housing and the finger. YMMV.

Charlie Hansen · From: Halifax, NS Canada and Various Southern Towns.

I just use a little wedge of wood.
_________________
I don't know much but what I know I know very well.
Carter S-10 3X5, Peavey Nashville 112, plus Regal dobro and too many other instruments to mention.
Bluegrass Island CFCY FM 95.1 Charlottetown, PE, Canada, on the web at cfcy.fm.
A Touch Of Texas CIOE FM 97.5 Sackville, NS, Canada,
on the web at cioe975.ca.

Bill Moore · From: Manchester, Michigan

I don't think anyone actually enjoys changing a full set of strings, it always takes a little time. The way I do it doesn't require any tool to hold the ball ends in place.

After the old strings are gone, I just grab a string, lay it on the guitar, estimate how much extra I need for winding on the key. Make a 90 degree bend at the correct location, then cut off the extra, leaving about 3/8” to go thru the key. Put it thru the key hole, then wind abut one turn on the key. Keep tension on the string with my left hand, while attaching the ball end with the right hand. Slide the right hand up the string so that I have tension on both ends of the string. Reach over with the left hand and wind the key as needed. On the heavier strings, I usually put a slight bend near the ball end to help keep it in place. The plain strings get a little extra length so they can have more windings on the key.

Jack Stoner · From: Kansas City, MO

The eraser and even cut down piano mute don’t work

Jon Light · From: Saugerties, NY

I was in love with the Williams hole-through-the-finger method. An excellent solution.

I've never had a keyless guitar or even studied on one until Stu Schulman had his keyless Desert Rose (I think one of only two in existence?....not sure about that) here for setup work and new strings.
In one motion you hook the string on the changer (I don't recall if it was a fork or a pin), run it through a hole, in the keyless piece, pull out the slack and wrap & tighten/lock. With that hole, it is easy to maintain hand tension. I changed out a set in about one third the time of my Williams.
I was sold! I'm not sure who designed this ....Stu was a bit confused but said he thought maybe Lamar? I was disappointed to learn that not all keyless rigs are the same.

Bill Duncan · From: Lenoir, North Carolina, USA

D Schubert · From: Columbia, MO, USA

Up to now I thought it was just me. Misery loves company. Will try the straw, eraser, and wedge tricks next time! 🤣

Jack Stoner · From: Kansas City, MO

GFI in an effort to make things simple has complicated the ham sandwich
A straw will be my next attempt

Jack Stoner · From: Kansas City, MO

After 2 hours my GFI has new strings. I used a round plastic piece I had similar to the straw.

There were a "few" ##$$%# words. I hope the Lord and Mother's forgive me.

FWIW I'm using SIT Sho-Bud gauges nickel. I like the nickel better than the SIT (Buddy Emmons) stainless strings that GFI uses.

Along with the string project, I had Spectrum here for several hours. Had lightning hit last evening and it took out the Internet modem and router, DVR, a splitter in the attic and one cable in the wall. Nothing else, just the cable equipment.

Patrick Edwards · From: Port Orchard, Washington, USA

I am curious Jack , did you find changing strings easier on the keyless GFI ?
Patrick

Tony Prior · From: Charlotte NC

A small wood wedge

_________________
Emmons L-II , Fender Telecasters, B-Benders , Eastman Mandolin ,
Pro Tools 12 on WIN 7 !
jobless- but not homeless- now retired 9 years

CURRENT MUSIC TRACKS AT > https://tprior2241.wixsite.com/website

Jack Stoner · From: Kansas City, MO

Jack Stoner · From: Kansas City, MO

Bruce Bjork · From: Southern Coast of Maine

Fred Martin · From: Phoenix, Az

I always had some foam ear plugs around. Squeeze em but in the slot and they expand. Ane colorful, I tell ya !

Richard Alderson · From: Illinois, USA

In my experience the GFI slots were always easier to negotiate than the pins, but I do keep a foam paint brushing tool in the strings box. The painting tool cost $1.25 and works the same as the pencil eraser and forms a wedge, its a thick stick handle with an inch and a half long tapered foam block at the end, bigger and twice as wide as the eraser tip, but does the same job. Most larger gauge strings I can do with 2 hands. Its those .10 and .11 and .12 that need help sometimes. But for me the GFI slots have mainly been a two handed operation while the pins were impossible without that third hand. What really sounds painful however is 8 months with the same strings ! What would Paul Franklin say ?
_________________
Derby SD-10 5x6; GFI S-10 5x5; GFI S-10 5x5; Zum D-10 8x7; Zum D-10 9x9; Fender 400; Fender Rumble 200; Nashville 400; Telonics TCA-500.

Bruce Derr · From: Lee, New Hampshire, USA

I have never found changing strings on my GFI Ultra keyless particularly difficult but I think I'll try the foam paint brush idea next time. Thanks for the tip.

I have keyed and keyless steels and I find changing strings on any of the keyless ones easier and faster than on any of the keyed ones.

Jack Stoner · From: Kansas City, MO

Just to clarify, I LIKE GFI's. If I didn't, I wouldn't have bought another. Just some issues I have, some also have them and from comments others do not.

Willie Sims · From: PADUCAH, KY, USA

i use half of a spring close pin,the wood end are shaped just right.

Larry Dering · From: Missouri, USA

From now on I'm having Jack Stoner change my strings. Haha. I'm looking at this for tips because I have several different brand steels and some are a challenge. I also manage to poke my finger with a string now and then.

Bill Duncan · From: Lenoir, North Carolina, USA

Forum Index > Pedal Steel	Goto page 1, 2 Next	Next oldest topic :: Next newest topic