| Author |
Topic: Mullen Adding Vertical Knee for B to Bb |
Thomas Green
From:
Michigan, USA
|
Posted 1 May 2022 10:09 am |
|
Hello All,
I just bought a nice PRP Mullen D-10 8+4. I would like to do a few things to it but I have never changed or added anything to steel. I am pretty mechanically inclined, but it would be amazing to see some videos of people making these modifications. I have three questions.
1. I would like to add a vertical knee lever. I reached out to Mullen and they said they do not have parts for PRP. Any advice on where to get these parts?
2. My current LKR lowers B to Bb. Ideally I would like that on the vertical knee lever. Any thoughts about where I could see some instructions for possibly doing this?
3. I do not have the "G" lever change, Raise 1 to G/G#, Raise 2 to E, and lower 6 to F#. Any thoughts about the feasibility of this and putting it on LKR?
Really appreciate the help in advance.
Last edited by Thomas Green on 17 Jul 2022 2:55 pm; edited 1 time in total |
|
|
 |
Mike Romero
From:
Bakersfield, CA
|
Posted 6 May 2022 9:55 am
|
|
| This would be great info for me too. Hoping someone chimes in! |
|
|
|
Thomas Green
From:
Michigan, USA
|
Posted 17 Jul 2022 2:54 pm
|
|
| So I got the parts for Mullen and well I guess I am stuck again. I wonder if I could even get a picture of what moving B to Bb to VKL would look like. If I had a picture of this puzzle. I could probably put it together. Anyone have a picture of the VKL lowering B to Bb? |
|
|
|
Paul Wade
From:
mundelein,ill
|
Posted 17 Jul 2022 3:11 pm Mullen guitar
|
|
Call mullen guitars they will walk you thru it
Paul |
|
|
|
Dave Meis
From:
Olympic Peninsula, Washington, USA
|
Posted 17 Jul 2022 6:32 pm
|
|
LKV on my PRP:
And here’s the lever lifted to show the stop. Nearest the rear apron.. no reverser needed..
Hope this helps.. |
|
|
|
Danny Letz
From:
Old Glory,Texas, USA 79540
|
Posted 18 Jul 2022 3:46 am
|
|
| Not to discourage you but I was told by some that in order to add across shaft to a PRP, you have to pretty much drop the whole undercarriage from the guitar. I hope this not true and some Mullen experts will set me straight. There may be work arounds. It looked to me like the center rib might be the problem???? |
|
|
|
Thomas Green
From:
Michigan, USA
|
Posted 18 Jul 2022 5:43 am
|
|
| Danny Letz wrote: |
| Not to discourage you but I was told by some that in order to add across shaft to a PRP, you have to pretty much drop the whole undercarriage from the guitar. I hope this not true and some Mullen experts will set me straight. There may be work arounds. It looked to me like the center rib might be the problem???? |
What I see is that the cross shaft in this kit has a screw which allows it to separate. I believe this will allow the installer to add the cross shaft without dropping the undercarriage. If the cross shaft were one piece, your statement would definitely be true. |
|
|
|
Mike Mantey
From:
Eastern Colorado, USA
|
Posted 18 Jul 2022 8:31 am
|
|
| It will install and look just like your RKL and LKL knee levers. You can just copy them. The location would be the hole after the 5th pedal. You can mount the lever where it fits and folds nicely. Usually in between the LKR and LKL lever typically right in the middle between the two should be clear. You can email or call with any questions. We really need to get some instructions and videos. It is on our list of stuff to do..... |
|
|
|
Danny Letz
From:
Old Glory,Texas, USA 79540
|
Posted 18 Jul 2022 9:39 am
|
|
Glad to hear that. I was hoping my misinformed reply would alert experts to straighten me out. And it got the man himself.  I have always gotten excellent customer service from Mullen. |
|
|
|
Mike Mantey
From:
Eastern Colorado, USA
|
Posted 18 Jul 2022 9:46 am
|
|
| Danny you are technically correct on that model, but we have devised a two part rod that bolts together to achieve this. otherwise you are correct. |
|
|
|
John McClung
From:
Olympia WA, USA
|
Posted 18 Jul 2022 11:03 am
|
|
I have a 2-segment crossrod on my PRP D12 9+10, I got it either from Mullen or might have had Jim Palenscar fabricate it, fuzzy on details decades later.
Tom Green, order from Mullen the short knuckle you attach to the crossrod bracket, the lever itself attaches to the other end of the knuckle. This yields a vertical lever that hangs lower and won't be at such an extreme angle when you make the final lever angle adjustment where the lever attaches to the knuckle. Very useful mod!
I like my vertical as close as possible to my left thigh.
I would like to see Mullen make that knuckle a little wider, the picture shows I can't get it any lower and have the angle set screw butting against metal of the lowering knuckle.
_________________
E9 INSTRUCTION
▪️ If you want to have an ongoing discussion, please email me, don't use the Forum messaging which I detest! steelguitarlessons@earthlink.net |
|
|
|
Mike Mantey
From:
Eastern Colorado, USA
|
Posted 18 Jul 2022 11:43 am
|
|
| We don't have a longer one John but you can add more than 1 |
|
|
|
Thomas Green
From:
Michigan, USA
|
Posted 18 Jul 2022 12:10 pm
|
|
| Mike Mantey wrote: |
| It will install and look just like your RKL and LKL knee levers. You can just copy them. The location would be the hole after the 5th pedal. You can mount the lever where it fits and folds nicely. Usually in between the LKR and LKL lever typically right in the middle between the two should be clear. You can email or call with any questions. We really need to get some instructions and videos. It is on our list of stuff to do..... |
I think that was the magic I needed. Once I lined up the parts on that hole, the picture made sense to me. |
|
|
|
John McClung
From:
Olympia WA, USA
|
Posted 18 Jul 2022 2:14 pm
|
|
Mike Mantey, I want to lower my vertical a little more, but if I lower it and back out the set screw on that knuckle, it no longer stops against metal. The knuckle needs to be wider on the left side. Make sense? Not the end of the world, the knuckle the way it is really helps make a PRP vertical far more ergonomic and comfortable. Genius little device.
_________________
E9 INSTRUCTION
▪️ If you want to have an ongoing discussion, please email me, don't use the Forum messaging which I detest! steelguitarlessons@earthlink.net |
|
|
|
Mike Mantey
From:
Eastern Colorado, USA
|
Posted 18 Jul 2022 2:28 pm
|
|
| John I see what you are saying. Adding another part would allow you to have the set screws in much farther and give you a whole 1" to mess with. A wider part would work but I don't like the set screw at that angle either. |
|
|
|
Thomas Green
From:
Michigan, USA
|
Posted 18 Jul 2022 7:27 pm
|
|
| Making progress with everyone's help. Now onto changing LKR to raise F#s to G#s and D# to E. |
|
|
|
Thomas Green
From:
Michigan, USA
|
Posted 19 Jul 2022 4:33 pm
|
|
| I made a video for this operation. Hopefully it helps those who need to do the same thing. https://youtu.be/LTY8HotxkWg |
|
|
|
Bobby D. Jones
From:
West Virginia, USA
|
Posted 19 Jul 2022 8:10 pm
|
|
| Mr. McClung Sent you a private message about your problem. |
|
|
|
Larry Dering
From:
Missouri, USA
|
Posted 20 Jul 2022 3:30 am
|
|
| Nice video with great details. Appreciate your time and effort to make this. Thanks. |
|
|
|
