| Author |
Topic: steel guitar cases |
Roy Thomas
From:
Louisiana, USA
|
Posted 24 Nov 2019 6:08 am |
|
| i have many steel guitar cases if some one needs one. there are different sizes and coverings. would need the exact measurements of the guitar so i can measure the case and let you know what i have. |
|
|
 |
DALE WHITENER
From:
TRINITY,NC USA
|
Posted 24 Nov 2019 3:50 pm
|
|
Any split cases?
Thanks
Dale |
|
|
|
Roy Thomas
From:
Louisiana, USA
|
Posted 25 Nov 2019 6:18 am split case
|
|
define split case
terminology is different in different areas. |
|
|
|
Garry Vanderlinde
From:
CA
|
Posted 25 Nov 2019 4:24 pm
|
|
Are there any with a tweed covering?
 |
|
|
|
DALE WHITENER
From:
TRINITY,NC USA
|
Posted 25 Nov 2019 5:26 pm
|
|
| I define split cases as a separate case for the legs and pedal bar and a case for the body |
|
|
|
Abe Levy
From:
California, USA
|
Posted 25 Nov 2019 5:35 pm
|
|
I’m looking for a tweed case for my fender dual pro...pm me if you’ve got one. Thanks!
_________________
Mostly Pre-1970 guitars. |
|
|
|
Bob Hoffnar
From:
Austin, Tx
|
Posted 26 Nov 2019 6:20 am
|
|
Roy, I need a case for an Emmons Legrande III D10. Check your private messages.
_________________
Bob |
|
|
|
Roy Thomas
From:
Louisiana, USA
|
Posted 26 Nov 2019 2:16 pm out of pocket
|
|
will be out of pocket for a week but i will look to see what i have and respond to all.
yes, there are some tweed in the mix.
i will try to post a picture with measurements to each one.
no, we never made a split arrangement, cases have compartments. |
|
|
|
Charley Bond
From:
Inola, OK, USA
|
Posted 29 Nov 2019 11:17 am Pedal Steel Case
|
|
Do you have one for a Sierra S-10
Hi Roy, hope you are doing well...
_________________
Steel Guitar players are members of a Special Family |
|
|
|
Charley Bond
From:
Inola, OK, USA
|
Posted 29 Nov 2019 11:24 am Split Cases
|
|
Split Cases used to mean the trucker had dropped it off the truck & it had split wide open Then it was wrapped with duct tape & wire...
Like Roy said, Split means different things to different folks...
_________________
Steel Guitar players are members of a Special Family |
|
|
|
John Groover McDuffie
From:
LA California, USA
|
Posted 29 Nov 2019 4:15 pm
|
|
  |
|
|
|
Jack Stoner
From:
Kansas City, MO
|
Posted 30 Nov 2019 3:07 am
|
|
I too have always considered "split cases" as a two piece set, one for the guitar and the other for the legs, pedal bar and pedal rods.
First "split case" set I had was a Fender 2000. It came with factory two piece case set. |
|
|
|
Roy Thomas
From:
Louisiana, USA
|
Posted 5 Dec 2019 11:07 am tweed case
|
|
been slow going but finally got to take pictures on one case.
the measurements are exact so you would have to allow 1/4" each side to make sure your guitar will fit. the stops can be moved around and you can change to your needed dimensions.
inside length: 34"
inside width: 11 1/2"
leg/pedal board length: 34"
leg/pedal board width: 3 1/4"
right stop: 2" from bottom
left stop: 2" from bottom
depth of bottom: 3 3/4"
depth of top: 2 1/2"
lid stops: 1 3/4"
this would accommodated a 5 1/2" cabinet
Last edited by Roy Thomas on 5 Dec 2019 11:20 am; edited 1 time in total |
|
|
|
Roy Thomas
From:
Louisiana, USA
|
Posted 5 Dec 2019 11:19 am measurements
|
|
the cases he has are made by other parties for his guitar size.
i do not have measurements of any guitars, i just was a machinist for him in my spare time.
if you send exact measurements, i can see what he has that can accommodate. the stops can be moved around.
i will post other cases when time permits. sorry for the delay, tooooo many irons in the fire. |
|
|
|
Roy Thomas
From:
Louisiana, USA
|
Posted 16 Mar 2021 1:17 pm cases
|
|
you may close this thread, appears that not many share near dimensions to fit these pedalmaster cases
thanks.
i will just make guitars for them |
|
|
|
Pat Moore
From:
Virginia USA
|
Posted 18 Mar 2021 6:00 pm tweed
|
|
Hi Roy,
That tweed case looks like it will fit my Emmons push pull. What would you take for it?
Thx, Pat |
|
|
|
