| Author |
Topic: Leg Tips std. 5/8 in. |
Jerry Overstreet
From:
Louisville Ky
|
Posted 5 Jun 2023 7:19 am |
|
5/8 in. i.d. fit most adjustable leg inserts. SS washer installed for corrosion resistance and punch out protection. These are the ones I use and like....much like the old Sho~Bud type. HD Rubber with nice thick pad, not plastic.
The cost has gone up but I'm sticking to my original offer of $4 ea. less than 4 or $15 set of 4 + postage.... as long as I can. First class mail has gone up too, but @ $5, postage is still OK for many conus regions. Remote locations, west coast might be a buck or 2 more. Please write for quote. International sales not desirable.
I don't paypal so I prefer money order, but check will work too.
Please contact my PM feature for more details.
Last edited by Jerry Overstreet on 5 Dec 2023 2:37 pm; edited 1 time in total |
|
|
 |
Jerry Overstreet
From:
Louisville Ky
|
Posted 1 Oct 2023 8:21 pm
|
|
| If your guitar has the common telescoping mic stand style legs with 5/8 in. inserts, these will fit your guitar. |
|
|
|
Jerry Overstreet
From:
Louisville Ky
|
Posted 27 Oct 2023 9:00 am
|
|
Tip when replacing your old leg tips with these. They are a little taller than the tapered style or your old ones of this type.
When installing these new ones on guitars that attach the pedal bar with sliding clamps, be sure the tips bottom out on the telescoping leg insert and don't deform against the pedal rack.
You will need to loosen up your pedal bar clamps, and extend the insert enough so there is adequate length for the leg tips to bottom out against the washers inside, then re-tighten the clamps. This may raise your guitar a skosh but should only be 1/8 in. or less.
The leg tips are not meant to support the pedal bar. That will squash the leg tips and reduce their useful life.
That's the job of the pedal bar clamps.
Be sure your pedal rack is up tight against the knurled adjusters and tighten the clamps down good.
Still have a few if interested. |
|
|
|
Jerry Overstreet
From:
Louisville Ky
|
Posted 6 Dec 2023 12:11 pm
|
|
| A few sets left. 🎅 |
|
|
|
Tony Edwards
From:
Six Mile, South Carolina
|
Posted 24 Jan 2024 8:43 am Leg Tips
|
|
Jerry,
I will take some if still available. Thanks.
Tony
_________________
ZumSteel SD10; CLR Custom SD10; Telonics 500-B w/ TT 15; Hilton Low Profile VP; Frenchy's Steel Mill Strings; George L's Cables; BJS Tone Bars; Hoffmeyer Picks. This combination produces a Heavenly tone! Psalm 33:2 "Praise the Lord with...an instrument of ten strings." |
|
|
|
Jerry Overstreet
From:
Louisville Ky
|
Posted 24 Jan 2024 9:16 am
|
|
| Yes sir. See your PMs. |
|
|
|
Tommy Wayne
From:
Nevada, USA
|
Posted 26 Jan 2024 7:33 am Hi
|
|
I'd like to get a set Jerry.
TW |
|
|
|
Jerry Overstreet
From:
Louisville Ky
|
Posted 26 Jan 2024 7:42 am
|
|
| Sent you a PM Tommy. |
|
|
|
Chris Brooks
From:
Providence, Rhode Island
|
Posted 26 Jan 2024 9:20 am
|
|
Me too, Jerry . . . .
Chris |
|
|
|
Jerry Overstreet
From:
Louisville Ky
|
Posted 27 Jan 2024 5:48 am
|
|
| Check PMs Chris. |
|
|
|
Jerry Overstreet
From:
Louisville Ky
|
Posted 10 Oct 2024 8:07 am
|
|
Please contact my PM service for inquiries, orders etc. Sales restricted to forum members only.
Have a few sets on hand. |
|
|
|
Matthew Lutton
From:
Indiana, USA
|
Posted 13 Oct 2024 1:56 pm Anyone know if these will fit a Fender Studio Console?
|
|
I was told the threads are 3/4”-10 whatever that means but I recently bought a Studio Console (the “champ on legs”) but didn’t realize it didn’t come with the legs, so I’m looking for some
Anyone know if these will fit this 50s model with 3 slanted legs or should I look elsewhere?
Thanks!🙏
_________________
Thanks!
Matt Lutton
Mrlutton@gmail.com
https://reverb.com/shop/matthews-boutique-2468 |
|
|
|
