| Visit Our Catalog at SteelGuitarShopper.com |

Post new topic looking for emmons wide floor pedals and crossrods?
Reply to topic
Author Topic:  looking for emmons wide floor pedals and crossrods?
Jack Goodson

 

From:
new brockton,alabama (deceased)
Post  Posted 17 Oct 2020 7:34 am    
Reply with quote

i am looking for 3 crossrods and the wide floor pedals for an emmons pp 1973 year model. let me know what you have?....thanks jack....also if anyone has an original pedal board with pedals would also consider that....thanks jack
View user's profile Send private message
Jack Goodson

 

From:
new brockton,alabama (deceased)
Post  Posted 17 Oct 2020 2:18 pm     ttt
Reply with quote

i appreciate any help on this, i really need this to get the ball rolling....thanks jack
View user's profile Send private message
Lynn Stafford


From:
Ridgefield, WA USA
Post  Posted 21 Oct 2020 1:59 pm     Pedals and Pedal Cross Bars
Reply with quote

Jack,

I can probably provide you with these items. Do the pedals on your guitar have the narrow 2 3/8" spacing? What position, or length do you need? You'll need to provide the length of your existing pedal cross bars. Please measure from the crank plate face to the end of the shaft to be sure you'll have adequate engagement into the support blocks on the rear apron. Hopefully, I'll have ones that are long enough, as they did vary a little through the years.
_________________
Best regards,
Lynn Stafford

STEEL GUITAR WEST
http://www.steelguitarwest.com
Steel Guitar Technician (Restoration, Set-up, Service and Repair work)

Previous Emmons Authorized Dealer & Service Technician (original factory is now closed)

ZumSteel Authorized Service Technician
----------------------------------
View user's profile Send private message Send e-mail Visit poster's website
Jack Goodson

 

From:
new brockton,alabama (deceased)
Post  Posted 21 Oct 2020 2:24 pm     Cross rods and pedals
Reply with quote

Here are some photos and measurements.... thanks Jack



View user's profile Send private message
Lynn Stafford


From:
Ridgefield, WA USA
Post  Posted 21 Oct 2020 4:03 pm     Pedals and Pedal Cross Bars
Reply with quote

Jack,

The pedal spacing appears to be the narrow 2-3/8".

I need the length of the round part of the three pedals you need (where the axel goes through). This length varies according to the pedal positions. I'm just trying to see if I have three pedals that will accommodate your needs.

It looks like the length of the pedal cross bars are about 8-15/16" from the end of the shaft to the face of the crank plate, correct?
_________________
Best regards,
Lynn Stafford

STEEL GUITAR WEST
http://www.steelguitarwest.com
Steel Guitar Technician (Restoration, Set-up, Service and Repair work)

Previous Emmons Authorized Dealer & Service Technician (original factory is now closed)

ZumSteel Authorized Service Technician
----------------------------------


Last edited by Lynn Stafford on 21 Oct 2020 5:01 pm; edited 1 time in total
View user's profile Send private message Send e-mail Visit poster's website
Jack Goodson

 

From:
new brockton,alabama (deceased)
Post  Posted 21 Oct 2020 4:21 pm     Rod is 9 7/16th the pedal is 2 3/8
Reply with quote

Photo is deceiving. I believe that the pedals are the same width except for the a pedal ....thanks jack
View user's profile Send private message
Jack Goodson

 

From:
new brockton,alabama (deceased)
Post  Posted 22 Oct 2020 12:10 pm     Parts?
Reply with quote

Lynn did you find any pedals or crossroads? Thanks jack
View user's profile Send private message
Jack Goodson

 

From:
new brockton,alabama (deceased)
Post  Posted 22 Oct 2020 2:17 pm     Parts?
Reply with quote

Lynn did you find any pedals or crossroads? Thanks jack
View user's profile Send private message
Lynn Stafford


From:
Ridgefield, WA USA
Post  Posted 22 Oct 2020 4:27 pm     Re: Parts?
Reply with quote

Jack Goodson wrote:
Lynn did you find any pedals or crossroads? Thanks jack


Jack,

The cross bars I have are about 1/8" too short (9-5/16") and I don't have any wide pedals for 2-3/8" spacing. The ones I have are for the wide, 2-3/4" spacing, so they would need to be machined shorter.
_________________
Best regards,
Lynn Stafford

STEEL GUITAR WEST
http://www.steelguitarwest.com
Steel Guitar Technician (Restoration, Set-up, Service and Repair work)

Previous Emmons Authorized Dealer & Service Technician (original factory is now closed)

ZumSteel Authorized Service Technician
----------------------------------
View user's profile Send private message Send e-mail Visit poster's website
Jack Goodson

 

From:
new brockton,alabama (deceased)
Post  Posted 23 Oct 2020 11:52 am     pedals and cross rods?
Reply with quote

lynn, would 1/8th shorter be a problem, could i put a stronger spring on the rear apron? also could u send a photo of the pedals u have. the pedal i sent a photo of is the A pedal....thanks jack
View user's profile Send private message

All times are GMT - 8 Hours
Jump to:  
Please review our Forum Rules and Policies
Our Online Catalog
Strings, CDs, instruction, and steel guitar accessories
www.SteelGuitarShopper.com

The Steel Guitar Forum
148 S. Cloverdale Blvd.
Cloverdale, CA 95425 USA

Click Here to Send a Donation

Email SteelGuitarForum@gmail.com for technical support.


BIAB Styles
Ray Price Shuffles for Band-in-a-Box
by Jim Baron