| Visit Our Catalog at SteelGuitarShopper.com |

Post new topic tone knob won't come off on my Excel
Reply to topic
Author Topic:  tone knob won't come off on my Excel
Oliver Samland


From:
Hamburg, Germany
Post  Posted 14 Mar 2019 8:10 am    
Reply with quote

The tone pot on my Excel came loose (when turning the knob, the pot turns also). I'll need to remove the knob. There is no little screw that holds the knob on the pot's shaft, so I guess it is just pressed on. I tried with quite some force to pull it off - with no sucess. Before I destroy it: am I missing something? Are there any other methods a knob can be fixed to a pot? (For instance, on the pot shaft is a tiny clip ring, I'm not sure if it might be accountable for holding the knob in place so I hestitate to remove it.)

Furthermore, this particular pot has an off switch/bypass switch when dialed back completely. I couldn't find a similar pot, where would I look for a replacement for such a pot?

Thanks in advance for any guidance!
Ollie


View user's profile Send private message Send e-mail
Michael Butler


From:
California, USA
Post  Posted 14 Mar 2019 8:36 am    
Reply with quote

i use two spoons underneath to lift up the knob.

play music!
_________________
please see my Snakeskin's Virtual Music Museum below.

http://muscmp.wordpress.com/
View user's profile Send private message Send e-mail Visit poster's website
Michael Maddex


From:
Northern New Mexico, USA
Post  Posted 14 Mar 2019 8:54 am    
Reply with quote

I don´t know what value pot you need, but AES has pots with switches:

https://www.tubesandmore.com/products/potentiometers_0?filters=Type/Size%3DSwitched

HTH. Good Luck with it! Cool
_________________
"For every expert, there is an equal and opposite expert." -- Arthur C. Clarke
View user's profile Send private message Send e-mail Visit poster's website
Bill A. Moore


From:
Silver City, New Mexico, USA
Post  Posted 14 Mar 2019 8:58 am    
Reply with quote

A couple of screw drivers usually work for me, but there is a "special" tool!
https://www.stewmac.com/Luthier_Tools/Tools_by_Job/Tools_for_Maintenance/Schatten_Knob_and_Bushing_Puller.html?utm_source=google&utm_medium=shopping&utm_campaign=2019-03-gp&gclid=CjwKCAjw96fkBRA2EiwAKZjFTatSRtYh48I5s0pfQmXLZfM0pMu4suOLkHstK_fXBbYTZMuysmijqxoC-BEQAvD_BwE
View user's profile Send private message Send e-mail
Chris Reesor

 

From:
British Columbia, Canada
Post  Posted 14 Mar 2019 9:18 am    
Reply with quote

Look again very closely with good light, Oliver. My Excel has an identical looking knob on the very small tone control pot, and it does have a set screw directly opposite the index line which takes a 1.5 mm hex key. If that is not the case here, then the knob probably has a spline to engage a splined pot shaft, and Mike's "two spoons" idea will probably get it off without damage.

The pot appears to already be well beyond salvation, and the knob is fairly easy to replace here in North America, so I'd just concentrate on not marring the endplate.

Antique Electronic Supply in the US has very similar knobs and appropriate pots available. (see the link in Michael Maddex's post above).

Have you contacted WBS steel guitars? Perhaps Wolfgang can help you closer to home.

Finally, could you post a picture or two of the whole guitar for us Excel fans?

Good luck with this.
_________________
Excel Superb U12, MIJ Squier tele, modified Deluxe Reverb RI, Cube 80XL, self built acoustics & mandolins
View user's profile Send private message Send e-mail
Mike Vallandigham

 

From:
Martinez, CA
Post  Posted 14 Mar 2019 2:34 pm    
Reply with quote

With the pressed on knobs on my Les Pauls, I take an old t-shirt, slide the edge under the knob skirt, and slide it so it goes all around the knob. This gives you a comfy handle to pull on, and won't damage the surface of the guitar.

Two spoons is a good idea too, just use protection!
View user's profile Send private message Send e-mail
Oliver Samland


From:
Hamburg, Germany
Post  Posted 14 Mar 2019 4:06 pm    
Reply with quote

Thank you guys for the helpful input!

2 little screwdrivers did the trick. Smile
As the knob is recessed into the backplate, spoons, cloth or that special knob removal tool (!) wouldn't fit in the tiny gap around the knob in this particular case. But these are all good ideas for more accessible knobs.
Luckily the pot still works just fine, I only need to solder the resistor back on (which came off because I ignored the problem for too long... Embarassed )

Chris, this Excel interstingly has serial number EX002 (or is it a label for the model?). Mitsuo said it is about 35 years old, like from the middle-eighties. Pretty amazing that he used basically the same parts back then already that he uses for recent Excel's. I ordered a vertical lever (the pics are from before I installed it), and it fits right in, easy installation, all the holes were pre-drilled.






View user's profile Send private message Send e-mail
b0b


From:
Cloverdale, CA, USA
Post  Posted 14 Mar 2019 4:13 pm    
Reply with quote

Excel has been making quality steels for a long time. Here's an ad from 40 years ago:

https://www.b0b.com/sgwest/pp7902p7.htm
_________________
-𝕓𝕆𝕓- (admin) - Robert P. Lee - Recordings - Breathe - D6th - Video
View user's profile Send private message Visit poster's website
Chris Reesor

 

From:
British Columbia, Canada
Post  Posted 14 Mar 2019 6:10 pm    
Reply with quote

Thanks for the pictures, Oliver. That looks like a sweet little guitar, and I'll bet it is pretty light too.

I'm glad you solved your problem.

I see split screws on the changer, I believe. Is that 5 raises and 3 lowers I see?

That is smart to maintain parts compatibility for such a long period. I guess you can do that when you get it right the first time. Meanwhile his changers and keyless models have evolved radically over that time frame.
_________________
Excel Superb U12, MIJ Squier tele, modified Deluxe Reverb RI, Cube 80XL, self built acoustics & mandolins
View user's profile Send private message Send e-mail
Mike Vallandigham

 

From:
Martinez, CA
Post  Posted 15 Mar 2019 1:17 pm    
Reply with quote

Even more interesting is the little black FUZZY sticker on the underside is the exact same sticker that just came on my 2018 S-12 Superb! With Mitsuo, I guess some things actually don't change.

I'm of the opinion that there are no two Excels that are exactly the same, even if you throw out color and number of pedals and knee. They all have a little tweak from the one that came before.

That's how Mitsuo rolls.
View user's profile Send private message Send e-mail

All times are GMT - 8 Hours
Jump to:  
Please review our Forum Rules and Policies
Our Online Catalog
Strings, CDs, instruction, and steel guitar accessories
www.SteelGuitarShopper.com

The Steel Guitar Forum
148 S. Cloverdale Blvd.
Cloverdale, CA 95425 USA

Click Here to Send a Donation

Email SteelGuitarForum@gmail.com for technical support.


BIAB Styles
Ray Price Shuffles for Band-in-a-Box
by Jim Baron