| Author |
Topic: Peavey Studio Pro 50 |
Rick Abbott
From:
Indiana, USA
|
Posted 15 Jun 2017 6:38 pm |
|
I got one of these for Christmas 1986 or 7. I saw one on fleabay for $55 and bought it several years ago as a piece of nostalgia. It had a blown speaker and I had a period-correct Scorpion speaker, so I put it in...it would have been the "upgrade" speaker at the time.
What I've discovered is: It's a pretty good steel amp! I took it to practice last week with my Gibson Console Grande, and this week with my Sho~Bud Professional. The tone and power were just perfect. I was really shocked at how good it sounded with the pedal guitar.
What a sweet little amp!
What upgrades would make it even better for steel? I could see having a few of these around.
Does anyone else have good, or bad, experiences with the Studio Pro 50?
_________________
RICK ABBOTT
Sho~Bud D-10 Professional #7962
Remington T-8, Sehy #112
1975 Peavey Pacer |
|
|
 |
Mike Wheeler
From:
Delaware, Ohio, USA
|
Posted 15 Jun 2017 7:24 pm
|
|
If you haven't done so already, take it to a tech and have him do a thorough inspection. It likely needs new power supply caps, and maybe a few other things, due to it's age.
Better safe than sorry.
_________________
Best regards,
Mike |
|
|
|
Richard Sinkler
From:
aka: Rusty Strings -- Missoula, Montana
|
Posted 15 Jun 2017 8:24 pm
|
|
I used on as the second amp in a stereo steel/keyboard setup. It is really a good steel amp. I did have an M series JBL in mine. It was also good for small gigs/practice.
_________________
Carter D10 8p/8k, Dekley S10 3p/4k C6 setup,Regal RD40 Dobro, Recording King Professional Dobro, NV400, NV112,Ibanez Gio guitar, Epiphone SG Special (open D slide guitar) . Playing for 54 years and still counting. |
|
|
|
Mike Brown
From:
Meridian, Mississippi USA
|
Posted 16 Jun 2017 6:02 am Peavey Studio Pro
|
|
Just a reminder, that we have factory technicians on hand that can repair or restore your early Peavey ampliers to factory spec at reasonable pricing. Our factory address is;
Peavey Service Center
Attn; Repair Department
412 Hwy. 80 East
Meridian, MS 39301
Please include a note of symptoms and your daytime phone number. |
|
|
|
Rick Abbott
From:
Indiana, USA
|
Posted 16 Jun 2017 6:58 am
|
|
Actually, it's working very well.
My real question is: Is there a chip set that would make it "better?"
It's not for every situation, but in this case ( amplified stand-up bass, light drums, amplified acoustic guitar) it really did the job!
_________________
RICK ABBOTT
Sho~Bud D-10 Professional #7962
Remington T-8, Sehy #112
1975 Peavey Pacer |
|
|
|
Mike Brown
From:
Meridian, Mississippi USA
|
Posted 16 Jun 2017 1:16 pm Chip set
|
|
| Peavey has not offered such as it was not a steel guitar amp. But, I will offer this, I "tried out" several of our amplifiers and reported on my findings about ten years ago and I thought that the Envoy sounded the best to my ears, as far as guitar amplifiers go. |
|
|
|
Len Amaral
From:
Rehoboth,MA 02769
|
Posted 16 Jun 2017 2:18 pm
|
|
I picked up this Peavey Encore several years ago. What a beautiful amp at 65 watts with a pair of 6L6 power tubes and three 12ax7 preamp tubes. Nice clean sounds with the steel but whoever designed the lead channel at Peavey must be an AC/DC fan. What a grinding driving tone.
Also, the Peavey LA-400 is very nice for steel guitar especially for a U-12 or C6 |
|
|
|
Rick Abbott
From:
Indiana, USA
|
Posted 16 Jun 2017 4:18 pm
|
|
| Mike Wheeler wrote: |
If you haven't done so already, take it to a tech and have him do a thorough inspection. It likely needs new power supply caps, and maybe a few other things, due to it's age.
Better safe than sorry. |
I just met a really good techie; they are rare where I'm from. I just might have him do a cap-job on it. I can see using it a fair amount. It's not enough for most gigs, but two might be on small to medium size. 
_________________
RICK ABBOTT
Sho~Bud D-10 Professional #7962
Remington T-8, Sehy #112
1975 Peavey Pacer |
|
|
|
Steven Paris
From:
Los Angeles
|
Posted 16 Jun 2017 5:25 pm Re: Peavey Studio Pro
|
|
| Mike Brown wrote: |
| Just a reminder, that we have factory technicians on hand that can repair or restore your early Peavey amplifiers to factory spec at reasonable pricing. |
OUTSTANDING!! Peavey is the best!
_________________
Emmons & Peavey |
|
|
|
Steven Paris
From:
Los Angeles
|
Posted 17 Jun 2017 7:50 am
|
|
The schematic doesn't indicate what type of chips were used; but if U1 & U2 are socketed 4558s, putting in OPA2134s would be an easy improvement. Caveat: U2 does NOT have power supply bypass capacitors, so it would be advisable to put in a 0.1uF ceramic capacitor across IC pins 4 & 8 to keep the faster IC from oscillating. Capacitors C5-C11-C20-C22 are electrolytics; polypropylene replacements would be an improvement. In addition, power supply capacitors C48-C49 could be upgraded to larger values (4,700-6,800uF) for a stiffer low end.
But if it sounds good as is, DON'T FIX IT!!
_________________
Emmons & Peavey |
|
|
|
Tony Oresteen
From:
Georgia, USA
|
Posted 26 Jun 2017 3:20 pm Re: Peavey Studio Pro
|
|
| Mike Brown wrote: |
Just a reminder, that we have factory technicians on hand that can repair or restore your early Peavey ampliers to factory spec at reasonable pricing. Our factory address is;
Peavey Service Center
Attn; Repair Department
412 Hwy. 80 East
Meridian, MS 39301
Please include a note of symptoms and your daytime phone number. |
Over the years I have sent a number of Peavey amps back to Peavey for service - a 400 Series Bass amp, RockMaster rack pre-amp, Encore 110, Bandit 112 etc and their service has always been outstanding. They are my go-to service guys for Peavey stuff.
_________________
Tony
Newnan, GA
Too many guitars, not enough time to play
'72 Sho-Bud 6139, '71 Marlen 210
'78 Fender Stringmaster Quad black
PedalMaster D8 |
|
|
|
