| Visit Our Catalog at SteelGuitarShopper.com |

Post new topic Fender 1000 setup help
Reply to topic
Author Topic:  Fender 1000 setup help
Kevin Ruddell

 

From:
Toledo Ohio USA
Post  Posted 27 Dec 2004 5:34 pm    
Reply with quote


I'm stringing and setting up a Fender 1000 D8 Pedal, and printed out the manual for the earlier model of the 1000 that a forum member kindly posted . Unfortunately some of the words are not very legible , esp. the tunings and adjustments in the manual. They do look pretty comprehensive for the A6 and E7 tunings Fender sent the guitars out with.
I understand the end adj. screws for raising and lowering string adjustments but am not sure if the pedal travel is to be set in any particular way other than just above the floor ? Any tips would certainly be appreciated.
I also wasn't sure if the pull rod hook end goes in the bell crank closest to the body edge so the hook faces in towards the player or the other way around ?
If I set up the inside neck with the 5,6,7,8 pedals and the eight strings lo to hi FACEGACE ; will the C6 instructional material that is available be something that will work ? Since I don't have any knee levers or ten strings that is . There are some screw holes in the bottom of the metal body and wood bottom where it appears a previous owner maybe mounted a lever and then removed it.
View user's profile Send private message Send e-mail
basilh


From:
United Kingdom
Post  Posted 27 Dec 2004 5:59 pm    
Reply with quote

With regard to pull rod hook end,
You can see it quite well here

(Courtesy of Darvin Willhoite)although this model is an early 1000 , the later ones had two holes for the pedal rods to allow more or less travel and leverage, as here... http://groups.msn.com/TheBritishSteeliesSociety/basilhenriques.msnw?action=Sho wPhoto&PhotoID=135

You can hear a Fender 1000 here.. http://www.waikiki-islanders.com/html/live_1.html
click on any of the tracks..

Basil


------------------
Quote:
Steel players do it without fretting





http://www.waikiki-islanders.com

[This message was edited by basilh on 27 December 2004 at 06:00 PM.]

View user's profile Send private message Send e-mail Visit poster's website
David Coplin


From:
Eugene, Oregon, USA
Post  Posted 27 Dec 2004 9:22 pm    
Reply with quote

Kevin,
Basilh beat me with the answer to part of your question. For the pedal rods: Hook the rods with the hooks pointing towards the player. It makes it easier to hook them up and remove them with the pedal board installed on the legs.Adjust each pedal to whatever feels comfortable to you but keep them high enough for full travel when pressed.
Remove any slack in the pull cables by turning the turnbuckles. Setting up the pedals and the pull cables to the proper pull-fingers is very easy on the 1000.You have two end adjust screws for each string.
The front screw raises and the rear screw lowers ( its the one with the spring )
You can use the Emmons set-up which you can find on a earlier forum post. Your
tuning FACEGACE (bottom to top) will work
but you wont have the knee levers, You will still be able to get a lot of great C6th
chords. E-mail me if I can help you with any more questions. I have a 1000 with a e9th & C6th setup with tone to the bone.
Dave
View user's profile Send private message Send e-mail
Kevin Ruddell

 

From:
Toledo Ohio USA
Post  Posted 28 Dec 2004 2:58 am    
Reply with quote

Thanks Basil and Dave for your help and the pictures.
View user's profile Send private message Send e-mail
Donny Hinson

 

From:
Glen Burnie, Md. U.S.A.
Post  Posted 28 Dec 2004 9:26 am    
Reply with quote

The silver screws in the endplate are for the raises, and the black screws control the lowers. There are no "pedal stop" screws. This was the primary cause of the loops breaking (when too much pedal pressure was applied). The height of the pedals could be adjusted on older models by turning the thumbscrew on the top of the pedal. The Fender-suggested tunings and setups were pretty dismal, and better tuning/pedal setups have been discussed here occasionally. Do a search using the words "Fender" and "1000" to find applicable threads.
View user's profile Send private message Send e-mail
Jody Carver


From:
KNIGHT OF FENDER TWEED
Post  Posted 2 Jan 2005 1:50 pm    
Reply with quote

I'm trying hard to limit my time to a few minutes a day on the computer. But I want to compliment Basil for a fine display of steel playing. Very good Basil. Enjoyed your playing very much.

Best to you.
View user's profile Send private message Visit poster's website
basilh


From:
United Kingdom
Post  Posted 2 Jan 2005 7:38 pm    
Reply with quote

Thanks Jody.....could you possibly e-mail me..
Thanks
Basil
click here :-
basil@waikiki-islanders.com
View user's profile Send private message Send e-mail Visit poster's website

All times are GMT - 8 Hours
Jump to:  
Please review our Forum Rules and Policies
Our Online Catalog
Strings, CDs, instruction, and steel guitar accessories
www.SteelGuitarShopper.com

The Steel Guitar Forum
148 S. Cloverdale Blvd.
Cloverdale, CA 95425 USA

Click Here to Send a Donation

Email SteelGuitarForum@gmail.com for technical support.


BIAB Styles
Ray Price Shuffles for Band-in-a-Box
by Jim Baron