| Author |
Topic: Oops |
Lane Gray
From:
Topeka, KS
|
Posted 16 Jun 2014 2:04 pm |
|
Perhaps one should pay attention to EVERYTHING one's doing?
_________________
2 pedal steels, a lapStrat, and an 8-string Dobro (and 3 ukes)
More amps than guitars, and not many effects |
|
|
 |
Scott Duckworth
From:
Etowah, TN Western Foothills of the Smokies
|
Posted 16 Jun 2014 3:15 pm
|
|
Well;, it's got clearance... 
_________________
Amateur Radio Operator NA4IT (Extra)
http://www.qsl.net/na4it
I may, in fact, be nuts. However, I am screwed onto the right bolt... Jesus! |
|
|
|
Martin Weenick
From:
Lecanto, FL, USA
|
Posted 16 Jun 2014 3:24 pm Oops
|
|
Don't worry Lane just cut the cable and super glue it back together.
_________________
Several custom steels. NV-112 Boss DD-7 |
|
|
|
Ken Pippus
From:
Langford, BC, Canada
|
Posted 16 Jun 2014 3:37 pm
|
|
| Allows it to expand and contract with temperature changes without binding. I think. |
|
|
|
Richard Sinkler
From:
aka: Rusty Strings -- Missoula, Montana
|
Posted 16 Jun 2014 3:49 pm
|
|
I don't see anything wrong. 
_________________
Carter D10 8p/8k, Dekley S10 3p/4k C6 setup,Regal RD40 Dobro, Recording King Professional Dobro, NV400, NV112,Ibanez Gio guitar, Epiphone SG Special (open D slide guitar) . Playing for 54 years and still counting. |
|
|
|
Storm Rosson
From:
Silver City, NM. USA
|
Posted 16 Jun 2014 3:55 pm
|
|
PERFECT!!!  |
|
|
|
Greg Johnson
From:
Greencastle, Pennsylvania, USA
|
Posted 16 Jun 2014 5:00 pm
|
|
keeps it from hanging below the frame... just saying
_________________
MSA CLassic SD-10
92 Emmons LII
79 Super Pro
Quilter TT
Evans FET 500
Fender Twin 65 RI
American Takimine |
|
|
|
Peter Freiberger
From:
California, USA
|
Posted 16 Jun 2014 5:27 pm
|
|
| That way it's handier for lifting the steel out of the case. |
|
|
|
Bent Romnes
From:
London,Ontario, Canada
|
|
|
|
b0b
From:
Cloverdale, CA, USA
|
|
|
|
John Billings
From:
Ohio, USA
|
Posted 17 Jun 2014 10:13 am
|
|
| Just use some duct tape! |
|
|
|
Lane Gray
From:
Topeka, KS
|
Posted 17 Jun 2014 10:20 am
|
|
I might. To hold the lead to the deck. But I expect I'll use the retainer at the top of the pic.
_________________
2 pedal steels, a lapStrat, and an 8-string Dobro (and 3 ukes)
More amps than guitars, and not many effects |
|
|
|
Carl Williams
From:
Oklahoma
|
Posted 17 Jun 2014 10:33 am
|
|
Lane, stop flaunting your Electrical Engineering knowledge!  Just "goes to show yee" that steel guitar players are human...Good luck with the fix...Carl |
|
|
|
Lane Gray
From:
Topeka, KS
|
Posted 17 Jun 2014 11:27 am
|
|
Carl, here's ANOTHER "Hey, dummy!" moment.
I've rodded up FOUR guitars from scratch (I think), each time I ran the rods through the fingers, and eyballed the bellcrank location.
ONLY SUNDAY did it occur to me to measure the distance from apron to finger for each string, then measure the apron-to-bellcrank distance on each cross-shaft. Probably shaved two or three hours of work.
When I shared my eureka moment with Denise, I got a "duh".
_________________
2 pedal steels, a lapStrat, and an 8-string Dobro (and 3 ukes)
More amps than guitars, and not many effects |
|
|
|
Carl Williams
From:
Oklahoma
|
Posted 17 Jun 2014 11:57 am
|
|
| Trust me Lane, those of us who have been around this contraption for a long while (like you of course) are going to have those infamous "Big Duh" moments:!: As you know, what counts is the "Ah Ha" moments that make you feel like you've whipped the problem and share your success with others. Carry on brother...Carl |
|
|
|
Mike Wheeler
From:
Delaware, Ohio, USA
|
Posted 17 Jun 2014 3:07 pm
|
|
Don't worry, Lane. With only 4 pulls in your guitar, it will be easy to fix. 
_________________
Best regards,
Mike |
|
|
|
I see that the price of loopers is coming down.