| Author |
Topic: Nashville 112 Settings |
Charley Adair
From:
Maxwell, Texas, USA
|
Posted 23 Feb 2007 9:28 am |
|
Just got a new NV112. Any suggestions on settings for pedal steel straight to the amp?
Thanks
Charley |
|
|
 |
James Marlowe
From:
Florida, USA
|
Posted 23 Feb 2007 10:22 am N112 settings
|
|
Hey Charley! Greetings from sunny Florida.
I"ve found these settings to work best for me:
Pregain 3
Low- +6
Mid- -15
Shift- 'bout 750
High- -3
Pr- -15
Main- 3+
My steel tends to be a little bright, thus the minus in the highs and presence.
I'm sure your "taste" will vary, but this works for me.
BTW, I didn't much like the N112 at first, but the longer you use it the better the sound gets. "They" say the speaker needs to be broken in.
Good luck finding the right tone.
Blessings to you,
jas. |
|
|
|
Morton Kellas
From:
Chazy, NY, USA 1
|
Posted 23 Feb 2007 11:15 am
|
|
| Charley, perform a search in the "old" forum under electronics and you will get several settings from good players. I use Randy Beavers settings and tweak from there. It depends on your equipment. Good luck. |
|
|
|
Charley Adair
From:
Maxwell, Texas, USA
|
Posted 23 Feb 2007 11:53 am
|
|
Thanks, James. I've written yours down and will try them.
Thanks, Morton. I did the search and found a lot of info. I had searched, but didn't realize I could search the old forum.
I got my amp yesterday and only got to play about 10 minutes thru it last night when I got back from San Diego. I have a wedding recept. to play tomorrow and won't get another chance to try it til then.
Charley |
|
|
|
Jack Stoner
From:
Kansas City, MO
|
Posted 23 Feb 2007 12:26 pm
|
|
Some of the settings will vary widely. But, it also depends on whether you have the amp sitting on the floor or if it's raised up on a stand or chair.
I sit mine on a stand and my "normal" or starting point settings are:
Low +9
Mid -3 and 800 Hz
High +1
Presence +1
This is on a Franklin D-10 with Lawrence 710 pickups and a Hilton Volume Pedal. |
|
|
|
Morton Kellas
From:
Chazy, NY, USA 1
|
Posted 23 Feb 2007 12:41 pm
|
|
Jack, that is the exact setting I am using at this time.
Zum Hybrid, Hilton and TC electronics M300 |
|
|
|
Bo Borland
From:
South Jersey -
|
Posted 24 Feb 2007 2:46 am
|
|
Charley, here are the NV112 settings I use on my Derby.. E9neck. I change a little low and mid for the C neck.
Pre gain 7
lows 12-15
Mid 3
Shift - about 750 -775
Highs -9
Pres 12
Rev 1-2 ( I use a delay so I don't use much reverb)
Master 3 -4
It sounds like a good place to start .
_________________
Bo Borland
Rittenberry SD10 , Derby D-10, Quilter TT12, Peavey Session 400 w/ JBL, NV112, Fender Blues Jr. , 1974 Dobro 60N squareneck, Rickenbacher NS lapsteel, 1973 Telecaster Thinline, 1979 blonde/black Frankenstrat
Currently picking with
Mason Dixon Band masondixonband.net |
|
|
|
