| Author |
Topic: New Software for transferring Vinyl to CD |
Jeff Strouse
From:
Jacksonville, Florida, USA
|
Posted 31 May 2002 1:58 pm |
|
I just found this:
http://www.sonystyle.com/electronics/prd.jsp?pid=12313
This topic comes up occasionally, so this software may be of help. It's called "Sony EZ Audio Transfer and Restoration Kit." It supposedly will work for cassette tapes, as well.
I haven't got it myself yet, but am seriously considering it. Does anyone know if it's avialable at a more discounted price?
Thanks! |
|
|
 |
Gary Pederson
From:
Van Nuys, Ca.
|
Posted 31 May 2002 5:47 pm
|
|
You might want to check out Rip Vinyl at www.wieser.clara.net/ripvinyl/orderinfo.htm
I've haven't used it yet & don't know how it compares with Sony other then price. Its only $7.00 to register. It was highly recommended on another forum.
Gary
|
|
|
|
Karlis Abolins
From:
(near) Seattle, WA, USA
|
Posted 31 May 2002 6:09 pm
|
|
I have been using Diamondcut 32 and a special phone preamp that plugs into my sound card to capture my old vinyl. It is an excellant program with lots of options for getting a clean sound with minimal pops and no rumble. I use Nero burning ROM to burn my processed recordings.
http://www.tracertek.com/diamond1.htm
Karlis Abolins |
|
|
|
Karlis Abolins
From:
(near) Seattle, WA, USA
|
Posted 1 Jun 2002 5:21 am
|
|
I meant phono preamp. It is a little unite that the turmtable plugs into and which then plugs into the line in jack on the computer sound card. It is an exceptional preamp which is rated as better than most of the phono preamps built into receivers. The results are well worth it.
Karlis Abolins |
|
|
|
Jim Smith
From:
Midlothian, TX, USA
|
Posted 1 Jun 2002 5:54 am
|
|
| I'm interested in the preamp, can you give details or a link to some info? |
|
|
|
Jeff Strouse
From:
Jacksonville, Florida, USA
|
|
|
|
Karlis Abolins
From:
(near) Seattle, WA, USA
|
Posted 4 Jun 2002 5:44 am
|
|
The preamp I bought from tracertek is not offered any more. It may still be available in Europe. Tracertek is now offering a Techlink preamp which should be equivalent.
http://www.tracertek.com/techlink.htm
Karlis Abolins |
|
|
|
Doyle Huff
From:
Broken Arrow, OK USA
|
Posted 13 Jun 2002 8:07 am
|
|
Jim Smith, if you know how to solder or know some one who can, there is a phono preamp kit. Go to www.plilmore.com/kits.htm.
I bought and assembled one yesterday and it seems to work well. I esimate the kit and the phono plugs etc. would probably run around $25.
Doyle |
|
|
|
Doyle Huff
From:
Broken Arrow, OK USA
|
Posted 13 Jun 2002 3:44 pm
|
|
Jim and Cairo. Sorry about being so dumn. Philmore was spelled wrong but the url would not work. Type in LKG Industries, there you will find Philmore. Philmore has been around for years. Again, sorry about that.
Doyle |
|
|
|
Scott Howard
From:
Georgetown, TN, USA
|
Posted 17 Jun 2002 6:01 pm
|
|
I ordered one and it works good for the recording and seperating but I am having problems getting it to burn a CD.
I used the burner program I already had and dragged the songs over and burned the new CD.
Keep in mind this is the first burner I have had so I am new to all this.I am also computer STUPID.But I have managed to transfer a tape to a CD.
I am sure it is something I am doing and I will figure it out when I have some time to work on it. |
|
|
|
, so I'm tyring to avoid the possible headaches of using 2-3 different software programs (and getting them to communicate with each other 
). If this one product will do it all, it might be worth it for the ease in accomplishing the task...