| Author |
Topic: How do I xfer settings to Profex from cache card |
Wiz Feinberg
From:
Mid-Michigan, USA
|
Posted 11 Jun 2004 10:28 am |
|
I just bought a Profex II which has both banks filled with lead guitar settings, but no steel settings. I am borrowing a Peavey RAM/Cache card with the Newman settings on it, and have it write protected. How do I delete the existing user settings, which occupy both A and B banks, and install the settings that are on the RAM card? Into which bank do I load the Newman settings on the RAM card?
I know how to create or edit my own presets, but have never had to clear out an entire unit and reprogram it from a card.
I read here that I should hold down the Play and Global buttons when powering on, to reset to factory defaults. I have done that twice, and all banks are still filled with the customized lead guitar settings that were on it when it arrived.
------------------
Bob "Wiz" Feinberg
AIM Screenname: Wizcrafts
1983 Rosewood Emmons D10 Push-Pull, with 8 pedals and 9 knee levers, George L's E66 pickups and aluminum necks. Nashville 400 amp with Peavey Mod. Emmons pedalbar mounted and Goodrich LDR volume pedals.
I use and endorse Jagwire Strings and accessories.
Keep Steelin' but don't get caught!
|
|
|
 |
Ken Fox
From:
Nashville GA USA
|
Posted 11 Jun 2004 12:01 pm
|
|
| I will email you instructions for uploading and downloading. |
|
|
|
Wiz Feinberg
From:
Mid-Michigan, USA
|
Posted 11 Jun 2004 12:14 pm
|
|
Ken;
Hold off on that, because my email server is down today.
I will mail you with an alternate address.
Wiz |
|
|
|
Jerry Horner
From:
Tahlequah, OK, USA
|
Posted 11 Jun 2004 12:48 pm
|
|
Ken, if you would, send that to me too.
Thanks
Jerry |
|
|
|
Mike Brown
From:
Meridian, Mississippi USA
|
Posted 11 Jun 2004 12:51 pm
|
|
| I invite you to contact here at Peavey toll free for a step by step guided tour. A paper tutorial is also available. |
|
|
|
Wiz Feinberg
From:
Mid-Michigan, USA
|
Posted 11 Jun 2004 2:23 pm
|
|
Mike;
You didn't leave a phone number, or webpage to go to.
Wiz[This message was edited by Wiz Feinberg on 11 June 2004 at 03:24 PM.] |
|
|
|
David Higginbotham
From:
Lake Charles, Louisiana, USA
|
Posted 11 Jun 2004 4:47 pm
|
|
Guys, to load the presets into the unit, insert the card, use the global button until you get to the "cart" menu, tab over to "load", press the execute button. The settings on the card will transfer to bank A. The settings in bank B are factory and unable to be deleted. By re-initializing the unit when holding the play and global buttons, you transferred bank B settings to bank A. They are duplicate settings. These will be over ridden once you install the card. Be sure to not re-initialize the unit after the card is loaded into the unit because you will lose the steel guitar settings.
Dave |
|
|
|
Wiz Feinberg
From:
Mid-Michigan, USA
|
Posted 11 Jun 2004 5:00 pm
|
|
Thanx David, that helps a lot! It also will save me a lot of borrowing the card over and over to reinstall the Bank A presets.
Does anybody have a blank spare card for sale?
Wiz[This message was edited by Wiz Feinberg on 11 June 2004 at 06:01 PM.] |
|
|
|
Jim Florence
From:
wilburton, Ok. US * R.I.P.
|
Posted 11 Jun 2004 5:39 pm
|
|
Ken's instructions are the easiest to follow, not to sell Peavey short, they build great stuff, but their tech writing is sometimes a little too technical for the layman.
Jim |
|
|
|
David Higginbotham
From:
Lake Charles, Louisiana, USA
|
Posted 11 Jun 2004 5:49 pm
|
|
your welcome Wiz! as for a card, you can use a roland 128, 256, or 512 "Ram" card. all you have to do is intialize the card to be read on the unit, then you can save the settings to the card. these cards are available on ebay usually for $50 or so. samedaymusic.com has the 512 new for $75 including shipping. you can also use a voice crystal ram card with at least 32k. however, I have never used a voice crystal card. hope this helps.
Dave
------------------
'74 MSA D-10 8&4 W/705's, Rocktron Short Timer, Profex II, Boss GX-700, Nashville 400
|
|
|
|
Wiz Feinberg
From:
Mid-Michigan, USA
|
Posted 11 Jun 2004 7:14 pm
|
|
Do these Roland cards have the same single metallic contact strip as the Peavey cards, or do they have individual contact fingers, like a pc card? Are they truly compatible? I am looking at a M-256E 32kb card.
Wiz |
|
|
|
David Higginbotham
From:
Lake Charles, Louisiana, USA
|
Posted 11 Jun 2004 7:51 pm
|
|
The Roland cards have the contacts not the single strip like the Peavey cards. Yes they are compatable with the Peavey-fex units. I have used these cards on profex and tubefex units and they work fine.
Dave |
|
|
|
