| Visit Our Catalog at SteelGuitarShopper.com |

Post new topic Nashville 400 hum
Reply to topic
Author Topic:  Nashville 400 hum
Don Burrows

 

From:
Ashtabula, Oh. USA
Post  Posted 7 Jan 2001 8:55 am    
Reply with quote

I have a Nashville 400 that hums when the reverb is turned up. If you turn the reverb off it quits. Also if you plug a jack into the pre-amp in the back, with or without anything else being plugged in the humming quits.
What could it be?
Thanks, Don
View user's profile Send private message Send e-mail
Jack Stoner


From:
Kansas City, MO
Post  Posted 7 Jan 2001 9:50 am    
Reply with quote

Check the reverb I/O molex connector on the underside of the chassis. That's usually the source of hum/noise in the reverb. Usually just removing the connector and spraying contact cleaner on both the female and male pins and then plugging the connector back in will take care of it.
View user's profile Send private message Send e-mail
Don Burrows

 

From:
Ashtabula, Oh. USA
Post  Posted 7 Jan 2001 10:39 am    
Reply with quote

The molex connector has been hard wired by somebody in the past, and all the wires seem to be tight where they sodered it.
Don
View user's profile Send private message Send e-mail
Bill Crook

 

From:
Goodlettsville, TN , Spending my kid's inheritance
Post  Posted 7 Jan 2001 11:07 am    
Reply with quote

Disconnect the leads from the reverb pan..... and see if the hum goes away.

It may be that the leads to the spring unit is reversed. A good indication of this is that the reverb sound will be somewhat weak but still work. it's common problem found after "fixes" on the reverb molex plugs are made.
View user's profile Send private message Send e-mail Visit poster's website
Don Burrows

 

From:
Ashtabula, Oh. USA
Post  Posted 7 Jan 2001 11:33 am    
Reply with quote

Bill, I tried reversing the leads and didn't make any difference.
Could it be in the pre-amp jack, being that when you plug a jack into it , it quits?
Anybody got any other suggestions?

Thanks Bill

Don
View user's profile Send private message Send e-mail
Bill Crook

 

From:
Goodlettsville, TN , Spending my kid's inheritance
Post  Posted 8 Jan 2001 12:59 am    
Reply with quote

Quote:
Could it be in the pre-amp jack, being that when you plug a jack into it , it quits?



I don't think so.....
Hum in the reverb tank circuit generally isn't caused by pre-amp amolities.

Keep searching in the reverb circuit.....

View user's profile Send private message Send e-mail Visit poster's website
C Dixon

 

From:
Duluth, GA USA
Post  Posted 8 Jan 2001 1:07 pm    
Reply with quote

When you say the molex connectors have been soldered, I am curious as to just how they did this.

Jack Stoner is correct, 99% of the hum when the reverb control is turned up, IS in fact due to a dirty contact in one or more pins on the molex connector. This is common on the Peavey Nashville 400.

Check to make sure that the molex connector is in fact not been soldered, but just appears tight. They are very tight by design but still are prone to dirty connections between mating pins.

Try this experiment. Turn up the reverb to where the hum is loudest. Reach under the chassis and wiggle the molex connector. If there is a change in the hum and/or elimination of the hum, I can almost guarantee you there is a pin or more that is not making good contact.

If this is the case, remove it. It may be very very tight. Then as Jack suggest, spray it with contact cleaner available from most any electronic supply house. Then reinsert it. Not a bad idea to disconnect and reinsert it several times to make sure you did get all the pins real clean. So they are ideed making good contact.

Good luck and God bless you with whatever you find to be the cause,

carl
View user's profile Send private message Send e-mail Visit poster's website
Mike Brown

 

From:
Meridian, Mississippi USA
Post  Posted 8 Jan 2001 1:37 pm    
Reply with quote

If any of the above suggestions fail to repair the 'hum' problem, please let me know and I will be glad to assist further.

Mike Brown
Peavey Electronics Corporation
View user's profile Send private message
clive swindell

 

From:
Huddersfield, West Yorkshire, UK
Post  Posted 9 Jan 2001 1:07 am    
Reply with quote

I have had the same problem and my technical man says it is the power transformer which is too near the reverb tank and which is interfering with it. The answer is to fit a different transformer which he is on with.

You can ask him at keith.knutton@cwcom.net if you want the details.
View user's profile Send private message Send e-mail Visit poster's website
Jim Smith


From:
Midlothian, TX, USA
Post  Posted 9 Jan 2001 5:59 am    
Reply with quote

If that's the case, why not just move the reverb tank?
View user's profile Send private message Send e-mail
clive swindell

 

From:
Huddersfield, West Yorkshire, UK
Post  Posted 9 Jan 2001 6:43 am    
Reply with quote

Yes, but where do you move it to? It is sat in the bottom of the cabinet.
View user's profile Send private message Send e-mail Visit poster's website
Jim Smith


From:
Midlothian, TX, USA
Post  Posted 9 Jan 2001 8:59 am    
Reply with quote

Evans mounts some of theirs on the side.
View user's profile Send private message Send e-mail
Bill Myrick

 

From:
Pea Ridge, Ar. (deceased)
Post  Posted 9 Jan 2001 7:36 pm    
Reply with quote

I once bought a Peavey Musician III Power head in a pawn shop that acted that way and come to find out someone had put the reverb pac back in backwards which put it too near the transformer. Can it be turned around 180 degrees ?
View user's profile Send private message Visit poster's website
Jack Stoner


From:
Kansas City, MO
Post  Posted 10 Jan 2001 3:35 am    
Reply with quote

The physical location of the reverb in the Nashville 400 should not be a problem. There are many amps out there that don't have excessive hum problems. The export model with the different transformer/voltage is a separate problem.

Plugging into the PREAMP out should not do anything as this is a parallel output and the same signal that goes to the POWER AMP IN. However, if a plug was put into the POWER AMP IN then there will be a difference. Maybe you are plugging in to the POWER AMP IN instead of the preamp out.

If you are putting a plug in the power amp in then the problem still goes back to the reverb circuit and back to either the reverb I/O connections or a reverb cable. Since the cables are soldered instead of the molex connector, it is possible that there is a bad solder connection on the circuit board for the reverb I/O. Whoever soldered the wires on could have used too much heat and screwed up the solder connection to the circuit board. Where the male pins are soldered on to the circuit board is a good place to check.

I would suggest you either take it to an amp tech or send it to Peavey for repair.
View user's profile Send private message Send e-mail
Louie Hallford

 

From:
denison tx
Post  Posted 16 Jan 2001 7:37 pm    
Reply with quote

I have the same problem with hum at my apartment where I keep my music. When I play out however it quietens down making me think it is grounging problem in the wiring at my apartment.....I have no florescents which will also cause hum.

[This message was edited by louie hallford on 16 January 2001 at 07:38 PM.]

View user's profile Send private message
Mike Brown

 

From:
Meridian, Mississippi USA
Post  Posted 17 Jan 2001 6:43 am    
Reply with quote

We'll be glad to take a look at the amp if you will send it to;

Peavey Electronics Corporation
Hwy. 80 East
Meridian, MS 39301

However, first let's discuss what the possible problems might be by phone. I can be reached here at Peavey by phoning 1-877-732-8391 in the U.S..
View user's profile Send private message

All times are GMT - 8 Hours
Jump to:  
Please review our Forum Rules and Policies
Our Online Catalog
Strings, CDs, instruction, and steel guitar accessories
www.SteelGuitarShopper.com

The Steel Guitar Forum
148 S. Cloverdale Blvd.
Cloverdale, CA 95425 USA

Click Here to Send a Donation

Email SteelGuitarForum@gmail.com for technical support.


BIAB Styles
Ray Price Shuffles for Band-in-a-Box
by Jim Baron