| Visit Our Catalog at SteelGuitarShopper.com |

Post new topic Amp losing power ..
Reply to topic
Author Topic:  Amp losing power ..
Steve Richter

 

From:
Neenah, WI USA
Post  Posted 16 Jan 2000 11:20 pm    
Reply with quote

I have a fender "The Twin" amp .. it seems to be losing power as the night wears on .. any of you tube amp guru's have any suggestions?

thanks

Steve
View user's profile Send private message Send e-mail
Jack Stoner


From:
Kansas City, MO
Post  Posted 17 Jan 2000 3:19 am    
Reply with quote

Are you sure it's the amp?? If you have any effects between the guitar and the amp, one of them may be causing it. If you do have effects, try to isolate what is causing the power loss - the effects or the amp.

If it's the amp, there are several general things to look at. Tubes are the main cause, whether it's the 6L6 output tubes or one of the 12AX7 preamps or the driver (either a 12AT7 or 12AU7 - I don't remember). If you have one with a rectifier tube (5U4) it could be the culprit too.

One other thing to consider is the AC line voltage. Many clubs really overload the AC line and a voltage drop could cause some power loss too.

There's really too many possibilites to do a "remote" troubleshoot.
View user's profile Send private message Send e-mail
Bobby Lee


From:
Cloverdale, California, USA
Post  Posted 17 Jan 2000 10:39 am    
Reply with quote

Turn it off between sets.
View user's profile Send private message Visit poster's website
Steve Richter

 

From:
Neenah, WI USA
Post  Posted 17 Jan 2000 11:01 am    
Reply with quote

LOL .. I thought about that this morning. But it's definitely the amp and nothing in the chain. My other amp maitains it's volume.
View user's profile Send private message Send e-mail
Donny Hinson

 

From:
Glen Burnie, Md. U.S.A.
Post  Posted 17 Jan 2000 5:07 pm    
Reply with quote

Take it to a technician, and tell him to check the coupling, or bypass capacitors, and also check the plate resistors. Either of these will cause that type of problem if they overheat.
View user's profile Send private message Send e-mail
Bobby Lee


From:
Cloverdale, California, USA
Post  Posted 17 Jan 2000 6:35 pm    
Reply with quote

I'm serious, Steve. The way I've found to get consistant performance from a tube amp is to turn it off between sets. Not just "Standby" - all the way off. Let it cool down.

------------------
Bobby Lee www.b0b.com/products
Sierra Session S-12 E9th, Speedy West D-10, Sierra S-8 Lap
View user's profile Send private message Visit poster's website
Mike Fried

 

From:
Nashville, TN, USA
Post  Posted 17 Jan 2000 10:00 pm    
Reply with quote

While b0b's advice may temporarily fix the power loss symptom, there is a problem there that should be addressed. Donny's recommendation is right on the money.
View user's profile Send private message Send e-mail Visit poster's website
Jerry Hedge

 

From:
Norwood Ohio U.S.A.
Post  Posted 17 Jan 2000 10:46 pm    
Reply with quote

Steve, it sounds to me like it could be new output tube (6L6) time. How old are they? If you change them be SURE you change the 12AT7 tube next to them. that's the phase inverter tube, and the only tube in the amp that works as hard as the 6L6s. Also have a tech set the bias if you change output tubes.

[This message was edited by Jerry Hedge on 17 January 2000 at 10:49 PM.]

View user's profile Send private message
David Mullis

 

From:
Rock Hill, SC
Post  Posted 18 Jan 2000 8:42 am    
Reply with quote

I thought the Fender "The Twin" was solid state? I know the Twin Reverb is Tube of course but a buddy of mine has one called "The Twin". It looks like a modern day Twin Reverb and his is solid state. Am I wrong?
View user's profile Send private message Send e-mail
Jay Ganz


From:
Out Behind The Barn
Post  Posted 18 Jan 2000 8:50 am    
Reply with quote

Best thing to do is, after the amp is good &
warm (with the loss of volume) have your tech
spray around with an aerosol "coolant" one
section at a time. That will quickly "chill
out" the culprit causing the power loss &
help to identify it quicker if it's a resistor or capacitor. The volume should jump back to normal when he hits it. But obviously this is only if tube substitutions don't do the trick right off the bat.
View user's profile Send private message Send e-mail Visit poster's website
Steve Richter

 

From:
Neenah, WI USA
Post  Posted 18 Jan 2000 1:36 pm    
Reply with quote

Bob .. I know you were serious, not sure where I saw the humor. I think taking it in for a checkup is the thing to do and investing in a tube job.

thanks for the tips!!

Steve
View user's profile Send private message Send e-mail
Craig Allen

 

From:
BEREA, KENTUCKY, USA
Post  Posted 18 Jan 2000 2:14 pm    
Reply with quote

You may be experiencing "brown out."

It does happen more often than you might think.

This happens when the venue can't supply enough power/electricity to supply everything in the place.

By all means check your power tubes,(if you have any), but don't rule out brown out.
View user's profile Send private message Send e-mail
Rodney Shuffler

 

From:
Montgomery, Texas USA (Home of the Bears)
Post  Posted 18 Jan 2000 3:53 pm    
Reply with quote

"The Twin" is a newer tube amp; or the 80's "red knob version". Both are tube and both are 100 watters; most any amp over 45-50 watts isn't going to have a tube recto and that's likely not the problem.

I'd guess caps....tubes never hurt either way. Rod

------------------
Rod's Place www.geocities.com/vibrasonic9/index.html



View user's profile Send private message Send e-mail Visit poster's website
Tom Ward

 

From:
Port Charlotte, FL 33952
Post  Posted 19 Jan 2000 4:02 am    
Reply with quote

I'd look for a voltage-dropping resistor in the output tube section that slowly changes value after it heats up (sometimes in the screen grid section). If that don't work trade it for a Nashville 400. Tom
View user's profile Send private message Send e-mail
Bill cole

 

From:
Cheektowaga, New York, USA
Post  Posted 19 Jan 2000 7:15 am    
Reply with quote

When you take it to get it checked make sure they change the fuel filter and chek the catalitic converter if either is pluged you will lose power
View user's profile Send private message Send e-mail
Steve Richter

 

From:
Neenah, WI USA
Post  Posted 19 Jan 2000 8:11 am    
Reply with quote

Are you sure?? I tried to get a pcv valve for it but they swore it didn't need a new one ... didn't even have one listed ..
View user's profile Send private message Send e-mail
David Mullis

 

From:
Rock Hill, SC
Post  Posted 19 Jan 2000 10:04 am    
Reply with quote

thanks for the correction, I could have sworn that my buddy that has one of those amps said it was solid state
View user's profile Send private message Send e-mail
Rodney Shuffler

 

From:
Montgomery, Texas USA (Home of the Bears)
Post  Posted 19 Jan 2000 10:25 am    
Reply with quote

Lemme see if I can do this:


The rest of the info is here: http://www.ampwares.com/ffg/index.html


------------------
Rod's Place www.geocities.com/vibrasonic9/index.html

[This message was edited by Rodney Shuffler on 19 January 2000 at 10:32 AM.]

View user's profile Send private message Send e-mail Visit poster's website
Bill cole

 

From:
Cheektowaga, New York, USA
Post  Posted 19 Jan 2000 10:25 am    
Reply with quote

nope don't remember that year havin no Pcv but it could be the Alternator aint alternatinor the carborator aint carbernatinor may the hootinany slip the whatchacallitand check the roght back wheel and make sure it aint turnin frontward or as my wife alway says. It sound like popcorn poppin
View user's profile Send private message Send e-mail
Bill cole

 

From:
Cheektowaga, New York, USA
Post  Posted 19 Jan 2000 10:28 am    
Reply with quote

Yep by golly that looks lika amplifier or else it's a heater for my music room and I could sure use one o dem bout now. Hey are we havin fun yet
View user's profile Send private message Send e-mail
Bill cole

 

From:
Cheektowaga, New York, USA
Post  Posted 19 Jan 2000 10:30 am    
Reply with quote

Hey I think I see the problem you see on the left corner it say fender now don't they belong on cars and trucks
View user's profile Send private message Send e-mail
Bobby Lee


From:
Cloverdale, California, USA
Post  Posted 19 Jan 2000 6:07 pm    
Reply with quote

Awww shucks!



(drawing by Bob Kosak)

View user's profile Send private message Visit poster's website
Bill cole

 

From:
Cheektowaga, New York, USA
Post  Posted 19 Jan 2000 6:49 pm    
Reply with quote

Darn that not sounds fermillar but it looks that way tooo
View user's profile Send private message Send e-mail

All times are GMT - 8 Hours
Jump to:  
Please review our Forum Rules and Policies
Our Online Catalog
Strings, CDs, instruction, and steel guitar accessories
www.SteelGuitarShopper.com

The Steel Guitar Forum
148 S. Cloverdale Blvd.
Cloverdale, CA 95425 USA

Click Here to Send a Donation

Email SteelGuitarForum@gmail.com for technical support.


BIAB Styles
Ray Price Shuffles for Band-in-a-Box
by Jim Baron