| Author |
Topic: Tone Block 202 |
Gary Hamblin
From:
Callao, VA
|
Posted 10 Jul 2024 4:47 pm |
|
Can 2 cabinets be with the Tone Block 202?
_________________
JCH/SD10 ,ZUM,D10 ,Rosewood Emmons Push Pull,T8 Fender Stringmaster.Nashville and Session 400,Walker Stereo Steel,Boss Katana 100 and John Hughey's Vegas 400.Hilton Pro Delay,Telonics Volume Pedal, Steelers Choice Seat,Live Steel Strings. |
|
|
 |
Chris Robbins
From:
Biggsville Illinois
|
Posted 10 Jul 2024 5:05 pm quilter 202
|
|
| Gary I run two 15 inch cabs with no problem |
|
|
|
Dale Rottacker
From:
Walla Walla Washington, USA
|
|
|
|
Danny Letz
From:
Old Glory,Texas, USA 79540
|
Posted 11 Jul 2024 7:31 am
|
|
| Dale, do you daisy chain them together or run one cable to the 4 ohm jack & one to the 8ohm jack? Are you using 4 or 8 ohm speakers? |
|
|
|
Mike Selecky
From:
BrookPark, Ohio
|
Posted 11 Jul 2024 8:03 am
|
|
From Quilter support:
https://support.quilterlabs.com/support/solutions/articles/60000943331-can-i-run-two-cabinets-with-my-head-
| Quote: |
Can I Run Two Cabinets With My Head?
Modified on: Wed, 15 May, 2024 at 10:56 AM
Absolutely! Our amps have two speaker outputs so you can build your own modular system.
Plug one into the "bottom" speaker jack and one into the top.
Note: On our amps, the "4 Ohm" jack has a special contact that increases the amplifier's output. This allows you to get additional headroom. It is advised to only plug in a single 4 ohm cabinet/speaker in this jack. Plugging a single 8 ohm cabinet/speaker into the 4 ohm jack will cause the output power to double and put strain on the amp. An 8 ohm cabinet/speaker should only be plugged into the 4 ohm jack if there is an additional 8 ohm cabinet/speaker in the 8 ohm jack. |
|
|
|
|
Danny Letz
From:
Old Glory,Texas, USA 79540
|
Posted 12 Jul 2024 6:35 am
|
|
| SO, if you were going to run two 4 ohm speakers, you’d plug one in the 4 ohm jack & the other in the 8 ohm jack? Is that correct? |
|
|
|
Ken Morgan
From:
Midland, Texas, USA
|
Posted 12 Jul 2024 6:59 am
|
|
I believe that would present a 2 ohm load to the amp. The manual specifies 4, 8, or 16 ohms, no mention of 2 ohms (that I saw) therefore it might not be wise. At low output might be OK but at even medium volumes the amp *might* overheat and shut off.
_________________
67 Shobud Blue Darling III, scads of pedals and such, more 6 strings than I got room for
Ken Morgan
Midland, TX |
|
|
|
Dave Meis
From:
Olympic Peninsula, Washington, USA
|
Posted 12 Jul 2024 9:39 am
|
|
I wrote Quilter about this a while ago, and here's their response:
"Hi Dave,
Running two 4 ohm cabinets into your Tone Block 202 would result in a 2 ohm load. The amp should be able to handle a 2 ohm load. But do note that in this case, if running the Master and Gain a bit high, the amp may begin clipping, which would sound like traditional solid state overdrive/distortion."
Best Regards,
Sam W, Sales/Customer Care Rep
Quilter Labs
Hope this helps. |
|
|
|
