Reno 400 - shuts off

Foster Haney · From: Ojai, CA

Hello all, I recently got a Reno 400 with blown speakers (it was a bass guitar) for a good price. I put my Eminence ESG in to test it and it was performing and sounding great (you knew that already tho). but now that I got new horns in, the amp shut off after about a minute of playing. my 15" is 4 ohms, and with the horns in I am still at 4 ohms. I don't think the horn is whats triggering the problem. maybe I should bypass it and do more testing. Has anyone had this problem before, or can lend some helpful words?

Also, are all the 400 series amps the same circuit? just different EQs and speakers?

Thank you, forum members.
_________________
1975 MSA Classic, AA1164 Princeton clone, Quilter Tone Block 202, Custom Warmoth Jazzmaster, two Kazou Yairi Alvarez Acoustics from the 80's, Acme Low B2 bass cab.

Dave Simonis · From: Stevens Point, WI USA

Foster, there is a Triac in the primary of the main power transformer that is used to control the AC to the transformer/amp. If your amp is shutting off, not blowing any fuses or tripping a breaker...I'd suspect something in this circuit and most likely the Triac or a capacitor leaking causing the Triac to shut down. If this is the issue, not an expensive fix. Find a local amp repair guy (or someone who works on amps) and he could replace easily.That would be my step one as that controls power to the amp. Next I would look at the filter caps in the 52V line, maybe leaking a bit and putting a load on the transformer...from there one thing at a time. Also, make sure speaker is 4 ohms - amp was designed for a 4 ohm only.
_________________
Dave Simonis

Fiddle: Zeta, Arthur Conner, many others.../Steel: GFI SD-10 Ultra.../Mandolin: Breedlove.../Guitar: Gibson, Fender, Taylor.../Amps: Peavey NV112, Evans FET 500.../Others: Hilton, Goodrich, Stereo Steel, Pendulum Pre-amp...

Foster Haney · From: Ojai, CA

Thank you Dave, I will start there.
_________________
1975 MSA Classic, AA1164 Princeton clone, Quilter Tone Block 202, Custom Warmoth Jazzmaster, two Kazou Yairi Alvarez Acoustics from the 80's, Acme Low B2 bass cab.

Ken Fox · From: Nashville GA USA

Note that the T.B. is normally closed and mounted to the top of an output transistor. You may have an output transistor overheating

As mentioned above power for the amp does not run thru the power switch, it runs through the Triac and fuse F3. The on/off switch handles a low current signal to operate the Triac

You could disconnect the horn to check that. Note sure if the original was 4 ohms, but it would have had a crossover, otherwise the amp would see a 2 ohm load if it was just in parallel with the speaker. That would overheat the transistors for sure

Foster Haney · From: Ojai, CA

Ken you hit the nail on the head, I hooked it back up and let it shut off again, that transistor is getting hot. Where can I get one? I am also having a hard time finding your website. Could you remind me of it?

I work on espresso machines for a living, and when I have free time I attempt to transfer those skills to amplifiers.
Thanks a ton.
_________________
1975 MSA Classic, AA1164 Princeton clone, Quilter Tone Block 202, Custom Warmoth Jazzmaster, two Kazou Yairi Alvarez Acoustics from the 80's, Acme Low B2 bass cab.

Ken Fox · From: Nashville GA USA

I would not recommend repairing it unless you are extremely familiar with power amp repair. Likely more wrong than just the outputs. I would send it to Peavey

John Fields · From: Collinsville, Mississippi; USA

It would be a good idea to shotgun all of the TO-3 power transistors and replace the insulators with real mica and plenty of thermal grease. Many Renos used the plastic film insulators with no grease and will often fail.
_________________
Thanks,
John C. Fields

Peavey's MI Engineering Manager (1997-current) Hessiemae Electronic Services (repairs/mods/parts)
hessiemae@hotmail.com
601-934-2163

Forum Index > Electronics		Next oldest topic :: Next newest topic

All times are GMT - 8 Hours	Jump to: