| Visit Our Catalog at SteelGuitarShopper.com |

Post new topic Oahu Acoustic Square Neck Tuning and String Tension
Reply to topic
Author Topic:  Oahu Acoustic Square Neck Tuning and String Tension
Mike Gobbi

 

From:
Acworth, Georgia, USA
Post  Posted 23 May 2023 8:50 am    
Reply with quote

Recently obtained a Vintage Oahu Acoustic square neck with an overall scale length of 24 inches and would like to tune it to open D. Have been perusing some posts that say that that the Oahu should be able to handle 160 lbs. of string tension. Before installing strings just want some opinions about the independent research done so far.

Using the String joy string tension calculator for acoustic 80/20 bronze strings relative to a standard acoustic guitar come up with the following results below, a total of 135.7 lbs. string tension using a standard acoustic guitar string gauges.

Have the following questions:

Would the relative tuning D4 A3 F#3 D3 A2 D2 work.

Would you recommend 80/20 Bronze or Phosphor Bronze Strings?

What do you think of the string gauges?

Please advise.






Last edited by Mike Gobbi on 14 Jun 2023 4:11 pm; edited 1 time in total
View user's profile Send private message
D Schubert

 

From:
Columbia, MO, USA
Post  Posted 23 May 2023 12:27 pm    
Reply with quote

I have an old Oahu student model square neck, the one with the . It works well with light gage acoustic strings tuned to D or lo-bass G. Medium gage strings and/or hi-bass tuning have caused the top to belly up and create a hairline crack in the top. Not very loud but sounds great with a Fishman soundhole pickup.
_________________
GFI Expo S-10PE, Sho-Bud 6139, Fender 2x8 Stringmaster, Supro consoles, Dobro. And more.
View user's profile Send private message Send e-mail
Mark Eaton


From:
Sonoma County in The Great State Of Northern California
Post  Posted 23 May 2023 12:37 pm    
Reply with quote

Phosphor bronze vs. 80/20 comes down to personal preference, how it sounds to your ear. I generally go with phosphor bronze on any lap style acoustic though I'm mainly referring to dobro.

I think your string gauges are too light for Open D. Especially the .012 first string. I believe you would be dissapointed with that one in particular - too wimpy.

Check out the 15-60 set from John Pearse in the link below. This is intended for a Weissenborn style guitar, a considerably more delicate instrument than the typical Oahu. I didn't find an overall string tension on the site, but I didn't look very hard either. There are even heavier gauge sets for Weissenborn from Pearse that are suitable for Open D.

I started out on steel taking lessons as a 10 year old in 1964, and before I went electric, for the first several monts at the music studio we played loaner flattop squareneck guitars guitars like Oahu, Kay, etc. They were the guitar equivalent of a Sherman tank. They had to be since they needed to be able withstand a lot of abuse dished out by young students.

https://www.juststrings.com/jps-3160l.html
_________________
Mark
View user's profile Send private message Send e-mail
Mark Eaton


From:
Sonoma County in The Great State Of Northern California
Post  Posted 23 May 2023 12:44 pm    
Reply with quote

D Schubert wrote:
I have an old Oahu student model square neck, the one with the . It works well with light gage acoustic strings tuned to D or lo-bass G. Medium gage strings and/or hi-bass tuning have caused the top to belly up and create a hairline crack in the top. Not very loud but sounds great with a Fishman soundhole pickup.


Interesting that the top bellied up and there was a hairline crack. But then it was likely a very old instrument and quality control wasn't exactly top notch to begin with in those days.
_________________
Mark
View user's profile Send private message Send e-mail
D Schubert

 

From:
Columbia, MO, USA
Post  Posted 23 May 2023 3:17 pm    
Reply with quote

I use much heavier strings on my Dobro. But if it’s the same student model Oahu that I’m familiar with, it’s very lightly constructed and won’t tolerate heavier strings. Not built as sturdy as a Dobro or even a higher-end Oahu.

Mark, I agree with your "wimpy-sounding" assessment of those string gages but my own experiments with heavier strings were almost a structural disaster.
_________________
GFI Expo S-10PE, Sho-Bud 6139, Fender 2x8 Stringmaster, Supro consoles, Dobro. And more.
View user's profile Send private message Send e-mail
Glenn Wilde

 

From:
California, USA
Post  Posted 24 May 2023 7:53 pm    
Reply with quote

It would help to know what model Oahu you have. I think the birch student models, basically Stella square necks are more robust than, say, a 66k. I run acoustic mediums down around C# on the 66k. I put a bridge Doctor in the 65k and it worked wonders with it's bellying, that one can take a bit more tension. I've had a few of the student ones and never had one come apart on me.
View user's profile Send private message Send e-mail
D Schubert

 

From:
Columbia, MO, USA
Post  Posted 25 May 2023 9:07 am    
Reply with quote

There is an Oahu squareneck for sale on the forum, like the one I've been describing.

https://bb.steelguitarforum.com/viewtopic.php?t=387551&highlight=
_________________
GFI Expo S-10PE, Sho-Bud 6139, Fender 2x8 Stringmaster, Supro consoles, Dobro. And more.
View user's profile Send private message Send e-mail
Michael Butler


From:
California, USA
Post  Posted 25 May 2023 7:13 pm    
Reply with quote

i have what seems to be pretty much the same oahu. i use open D and i'm using 12/54 strings but i don't remember the brand i used. no problem with the tension and playability.

play music!
[/img]
_________________
please see my Snakeskin's Virtual Music Museum below.

http://muscmp.wordpress.com/
View user's profile Send private message Send e-mail Visit poster's website
Brian Cheetham

 

From:
Maryland, USA
Post  Posted 26 May 2023 1:22 pm     Asher acoustic
Reply with quote

I put Asher Acoustic Hawaiian lap steel strings on mine .014-.058
View user's profile Send private message Send e-mail

All times are GMT - 8 Hours
Jump to:  
Please review our Forum Rules and Policies
Our Online Catalog
Strings, CDs, instruction, and steel guitar accessories
www.SteelGuitarShopper.com

The Steel Guitar Forum
148 S. Cloverdale Blvd.
Cloverdale, CA 95425 USA

Click Here to Send a Donation

Email SteelGuitarForum@gmail.com for technical support.


BIAB Styles
Ray Price Shuffles for Band-in-a-Box
by Jim Baron