Changing Strings

Larry Ball · From: Airdrie, Alberta, Canada

Well I think I joined that “Club” of @#&$$@$ new words when changing strings with pins on the changer. I have read all the archives for string changes and found one technique that worked great. That one was the eraser holding the ball on the pin of the changer. However newer changers may be different as mine is so I had to trim down the eraser so that it fit to hold the ball while attaching the string to the key head. This was my first attempt at changing strings with this type of pin on the finger. However with some lighting adjustments to help me see the pin clearly things started to move quickly. I know how to attach the string to the key and with a drill doing the winding .. Shazam…

My other Steels have groves on the finger for the ball to slid into.

I guess this is just something else that keeps things interesting with this amazing instrument.
_________________
Mullen SD10, Sho~Bud SD10 LDG, Show-Pro SD10 LDG, Peavey Nashville 112, Boss Katana 100 MK11, Telonic's F100 Multi-Taper Super Pro V/P,

Tucker Jackson · From: Portland, Oregon, USA

Yeah, those pins are hard to deal with. Glad you got it handled, Larry.

I take the paper envelope from the string, fold it up into a little square and cram that in the slot at the back of the changer. Works surprisingly well.

Roger Crawford · From: Griffin, GA USA

One leg of a wooden clothespin always worked for me.

Jerry Overstreet · From: Louisville Ky

Lots of guys recommend a piano tuning mute. Appear to be about the right taper. You get a few of these for about $10 or less at amazon, ebay etc. I'll probably pick up one one of these days. Might work better than the pencil eraser I use. I play so little I hardly ever break or change strings anymore.

Bobby D. Jones · From: West Virginia, USA

With so many different designs of changer housings, Pins and Slots for strings. Seems you have to chose a way with each guitar to hold the string ball in or on its anchor point.

I played a guitar for several years I built, It had pins in the fingers. I was in the kitchen and saw a rubber spatula with a broken handle. White rubber from about 1/16" to 3/8" taper. Cut about a 1/2' strip out of the middle of it, Worked great for a long time.

I went to MSA's with slots in the fingers. With Key Heads I had no problem, Hook ball in slot measure and cut. If it slid out of the slot just hook it back in the slot, Hold it snug, Insert string in hole on key, Place power screwdriver on key wind the string.

Went to GFI S12, With slots and keys no problem.
Then I went to a GFI S12 Keyless. With a screw holding the end of the string in the tuning lever. Stretching and wrapping the string around the screw was touchy. Here is what I use with the GFI Keyless

The little brass cylinder with guitar string wrap and hooked to parachute cord, Bar case works great. The brass cylinder follows the string ball in the slot and weight of bar and case, Holds the string solid in the slot while tightening the string and locking the screw.

Eric Philippsen · From: Central Florida USA

A little rectangular pencil eraser works for me on Emmons.

Somewhat off subject, after 50 years of changing sttings I just learned a new-to-me string changing tip. That is, put the ball end’s burr facing out from the finger. Don’t have it laying directly against the finger. Have it facing out before you tighten the string to pitch.

Jack Stoner · From: Kansas City, MO

I had 2 with pins, an Emmons and a Franklin. I now have a GFI with slot in fingers. Even with Bobby's ball holding gadget its still. for me. easier and quicker with the pin type.

Mike Polansky · From: Austin, TX

I just lightly jab the pointy end of a Bic mechanical pencil in there. Works fine. I don't know why you'd need anything else.

chuck lemasters · From: Jacksonburg, WV

I use a small piece of soft rubber hose, shoved in horizontally.

Forum Index > Pedal Steel		Next oldest topic :: Next newest topic

All times are GMT - 8 Hours	Jump to: