| Author |
Topic: Where can I find a 10-32 national coarse thread die? |
David Neslony
From:
Arlington, TX USA
|
Posted 14 Jan 2023 11:38 am |
|
Where can I find a 10-32 national COARSE thread cutting die?
All I've been able to find are 10-32 FINE thread cutting dies. |
|
|
 |
Jerry Overstreet
From:
Louisville Ky
|
Posted 14 Jan 2023 11:44 am
|
|
10-24 is a UNC SAE coarse thread die. 10-32 is fine thread. 10-24 is a common coarse thread size and should not be hard to find.
Dimensions are screw size, #10 in this case and either 24 or 32 threads per in [TPI]. depending on pitch.
JIC you don't know, if you're cutting new threads on a blank, you will need an adjustable thread cutting die and not a thread chaser or re-threader. |
|
|
|
David Neslony
From:
Arlington, TX USA
|
Posted 14 Jan 2023 12:02 pm
|
|
Thanks, Jerry!
David Neslony |
|
|
|
Jerry Overstreet
From:
Louisville Ky
|
Posted 14 Jan 2023 12:50 pm
|
|
Of course. Don't know what you're working on, but several components on a pedal steel use 10-32 fine threads, such as most pedal rods, connectors etc.
Good luck with your project. JO. |
|
|
|
Bobby D. Jones
From:
West Virginia, USA
|
Posted 14 Jan 2023 3:28 pm
|
|
From your previous post on shortening your pedal rods. Take 1 of the pedal rods with you, So you can get a proper fitting die.
If you have an Ace Hardware in your town or a NAPA store they should have a 10-32 die. |
|
|
|
David Neslony
From:
Arlington, TX USA
|
Posted 14 Jan 2023 6:27 pm
|
|
I took a nut from the pedal rod to ACE hardware and they said it was 10-32 NF. But the depth of thread was too fine.
It is a pedal rod to an MSA "The Universal". |
|
|
|
Jimmie Hudson
From:
North Carolina, USA
|
Posted 14 Jan 2023 6:48 pm 10-32
|
|
| David Neslony wrote: |
I took a nut from the pedal rod to ACE hardware and they said it was 10-32 NF. But the depth of thread was too fine.
It is a pedal rod to an MSA "The Universal". |
The most of the pedal rods have rolled threads on the from MSA. The rods are smaller than a normal rod used to thread to 10/32 so the threads will be thin on the rod if you try to thread the factory rod. |
|
|
|
Ronald Sikes
From:
Corsicana, Tx
|
Posted 15 Jan 2023 5:52 am
|
|
I’ve rethreaded pedal rods using an adjustable 10-32 thread die. It seems like I had to go a bit deeper but I don’t remember exactly. Jimmies right , they are a rolled thread but this will work.
If you’re in Arlington, you might reach out to Kyle at MSA and I’m sure he could fix you up.
_________________
Show Pro #26 & #83,BJS bars,Stereo Steel,Tommy Huff cabs loaded with JBL D130's, Wampler pedals,NV112,NV400, Steelers Choice Seats |
|
|
|
David Neslony
From:
Arlington, TX USA
|
Posted 17 Jan 2023 7:19 pm I found the correct die
|
|
I found and purchased this. It was about $8.00 and works great! I bought it through Amazon. Delivered the next day.
Do a search for:
Drill America #10-32 1"OD High Speed Steel Round Adjustable Die, DWT Series
It was indeed NF.
Thanks everyone who helped me.
David Neslony
------------------------------
Here's a follow up to the above:
The pedal rod is 3/16" on this MSA "The Universal".
I was able to thread 7 pedal rods.
On the 8th rod that I attempted to thread,
the die would no longer cut.
So I had to order a new one.
If you're going to thread these rods that are stainless,
I would suggest buying 2 dies in this size.
It's still a bargain.
David Neslony |
|
|
|
David Neslony
From:
Arlington, TX USA
|
Posted 20 Jan 2023 11:25 am How to use an adjustable die?
|
|
What is the correct way to use an adjustable die?
David Neslony |
|
|
|
Paul Redmond
From:
Illinois, USA
|
Posted 20 Jan 2023 7:16 pm
|
|
McMaster-Carr ..... and you'll have it in two days.
PRR |
|
|
|
Dave Magram
From:
San Jose, California, USA
|
Posted 21 Jan 2023 7:20 am Re: How to use an adjustable die?
|
|
| David Neslony wrote: |
What is the correct way to use an adjustable die?
David Neslony |
Travers Tool - Adjustable Round Dies (How to use them)
https://www.youtube.com/watch?v=ewtt8N1hFJg&t=99s
- Dave |
|
|
|
