| Author |
Topic: Stripped screw hole holding endplate to body repair question |
Brian Spratt
From:
Oklahoma, USA
|
Posted 3 Oct 2022 6:35 am |
|
I have a couple of these screws (circled below) that are stripped on my guitar. Can this be fixed with wood glue and toothpicks directly into the hole without disassembling the guitar? Or would it be advisable to take the endplates off and drill the hole out and glue a dowel in and re-drill the hole. Or something else entirely?
 |
|
|
 |
Jerry Overstreet
From:
Louisville Ky
|
Posted 3 Oct 2022 9:44 am
|
|
I defer to the Emmons experts among us, but I believe I'd try the toothpick/glue method first. That looks like a left endplate which has nothing attached, so pulling it off wouldn't require any disassembly....but, those end plates fit really snug requiring use of a dead blow hammer in most cases to remove/install.
I guess there is the issue of the stripped screw allowing it to drift out of alignment, but I believe that they fit so tight, a stripped screw won't matter much long as it's in place. But I would go ahead with the toothpick/glue repair if it's me.
I'm quite sure the experts in the field will correct and reprimand me in the event this is unadvisable. |
|
|
|
Willie Sims
From:
PADUCAH, KY, USA
|
Posted 3 Oct 2022 11:35 am
|
|
| you might try glue and wood filler mixed ,then fill the hole and then,put the screws in before the filler dry's.it might work. |
|
|
|
Bob Cox
From:
Buckeye State
|
Posted 3 Oct 2022 12:31 pm fill
|
|
| JB weld will work |
|
|
|
Henry Matthews
From:
Texarkana, Ark USA
|
Posted 3 Oct 2022 12:51 pm
|
|
Tooth picks and wood glue is easiest and best fix. Dip a few tooth picks in Elmers, cut to proper length to depth of screw hole, insert and let glue dry. It’ll hold.
_________________
Henry Matthews
D-10 Magnum, 8 &5, dark rose color
D-10 1974 Emmons cut tail, fat back,rosewood, 8&5
Nashville 112 amp, Fishman Loudbox Performer amp, Hilton pedal, Goodrich pedal,BJS bar, Kyser picks, Live steel Strings. No effects, doodads or stomp boxes. |
|
|
|
Bob Carlucci
From:
Candor, New York, USA
|
Posted 4 Oct 2022 1:18 am
|
|
| Henry Matthews wrote: |
| Tooth picks and wood glue is easiest and best fix. Dip a few tooth picks in Elmers, cut to proper length to depth of screw hole, insert and let glue dry. It’ll hold. |
Agreed.. Once the glue dries, the new material[glue and toothpicks] is harder than the original wood.. Plain old Elmers is fine, but Titebond or Elmers Wood Glue is actually stronger....
_________________
I'm over the hill and hittin'rocks on the way down!
no gear list for me.. you don't have the time...... |
|
|
|
Darvin Willhoite
From:
Roxton, Tx. USA
|
Posted 4 Oct 2022 7:34 pm
|
|
I use JB quick weld with no plug on smaller holes, on larger holes I use a piece of hardwood dowel. A pilot hole can be drilled easily after the JB sets up.
_________________
Darvin Willhoite
MSA Millennium, Legend, and Studio Pro, Reese's restored Universal Direction guitar, a restored MSA Classic SS, several amps, new and old, and a Kemper Powerhead that I am really liking. Also a Zum D10, a Mullen RP, and a restored Rose S10, named the "Blue Bird". Also, I have acquired and restored the plexiglass D10 MSA Classic that was built as a demo in the early '70s. I also have a '74 lacquer P/P, with wood necks, and a showroom condition Sho-Bud Super Pro. |
|
|
|
Brian Spratt
From:
Oklahoma, USA
|
Posted 6 Oct 2022 10:15 am
|
|
| The toothpick and glue method seems to have worked out pretty well. Thanks for the responses. |
|
|
|
