| Author |
Topic: 3rd Party Racks for Sho-Bud Rack & Barrel |
Tony Oresteen
From:
Georgia, USA
|
Posted 4 Jun 2017 12:00 pm |
|
I've located a couple of pedals for my 1972 6139 Sho-Bud and have a WTB ad for the rack parts.
Does anyone know of a 3rd party that makes (or made) replacement racks for the Sho-Bud Rack & Barrel system?
Thanks!
_________________
Tony
Newnan, GA
Too many guitars, not enough time to play
'72 Sho-Bud 6139, '71 Marlen 210
'78 Fender Stringmaster Quad black
PedalMaster D8 |
|
|
 |
Rick Abbott
From:
Indiana, USA
|
Posted 4 Jun 2017 12:07 pm
|
|
http://www.psgparts.com/
_________________
RICK ABBOTT
Sho~Bud D-10 Professional #7962
Remington T-8, Sehy #112
1975 Peavey Pacer 1963 Gibson Falcon |
|
|
|
Tony Oresteen
From:
Georgia, USA
|
Posted 4 Jun 2017 10:51 pm
|
|
| Rick Abbott wrote: |
| http://www.psgparts.com/ |
Thanks Rick. I looked at PSG. They have the rods and barrels that I will need but I did not see the bell cranks or the dual guides that the rod & barrel system needs.
http://www.psgparts.com/ShoBud_c2.htm
I spoke to Michael a couple of weeks ago about adding knee levers to my rack & barrel Sho-Bud. He's working on a knee lever kit for the rack & barrel Sho-Bud but it will not be available for some months, if ever. Some of the pedal parts are the same as the knee lever parts so I think that they are in the same boat.
I've sent Michael an email and hopefully he has them or can make them - at some time.
In the mean time, I am looking at all possible sources for these parts.
_________________
Tony
Newnan, GA
Too many guitars, not enough time to play
'72 Sho-Bud 6139, '71 Marlen 210
'78 Fender Stringmaster Quad black
PedalMaster D8 |
|
|
|
Lane Gray
From:
Topeka, KS
|
Posted 5 Jun 2017 3:35 am
|
|
I'm under the impression that two-hole pullers and cross-shafts, from the next generation of Buds, are compatible with racks, and will also be noticeably lighter.
_________________
2 pedal steels, a lapStrat, and an 8-string Dobro (and 3 ukes)
More amps than guitars, and not many effects |
|
|
|
Justin Griffith
From:
Taylor, Texas, USA
|
Posted 6 Jun 2017 6:48 pm
|
|
Correct Lane. I have a couple boxes of rack&barrel stuff. I may have what you need.
_________________
Emmons/Sho~Bud/Blanton, Fender/Peavey.
Telonics pedal |
|
|
|
Liam Millett
From:
Austin, Texas
|
Posted 22 Aug 2022 9:32 am
|
|
Hey all, I wanted to bring this post back to the surface because I am looking for rack parts for my Fender S10 3x1 student model, which currently has no pedals, pull rods or a rack. I can probably find good pedals, and Michael from psgparts.com said he could provide rods and quick connects. I'm also being told that ShoBud parts might work for this model, as Fender seemed to partner with ShoBud on this.
So, Justin, I know it's been a few years, but do you still have those boxes of rack and barrel stuff? |
|
|
|
Richard Sinkler
From:
aka: Rusty Strings -- Missoula, Montana
|
Posted 22 Aug 2022 10:17 am
|
|
I don't think the Maverick or the Fender/Sho~Bud ever used the rack & barrel system.
Maverick undercarriage:
_________________
Carter D10 8p/8k, Dekley S10 3p/4k C6 setup,Regal RD40 Dobro, Recording King Professional Dobro, NV400, NV112,Ibanez Gio guitar, Epiphone SG Special (open D slide guitar) . Playing for 55 years and still counting. |
|
|
|
Jerry Overstreet
From:
Louisville Ky
|
Posted 22 Aug 2022 10:32 am
|
|
Liam, I think you are looking for a pedal bar[rack] and floor pedals.
This topic is about the rack and barrel string pulling system mechanics for the underside of the guitar. The rack being the stationary stop part that the pull rod/barrel contacts when pedal or knee is actuated. That is what is being discussed here.
 |
|
|
|
