| Author |
Topic: sitar bar question |
Tommy Auldridge
From:
Maryland, USA
|
Posted 13 Aug 2021 8:52 am |
|
| On a sitar bar, how wide is the flat part usually? Just wondering. Thanks, Tommy..... |
|
|
 |
Jerry Overstreet
From:
Louisville Ky
|
Posted 13 Aug 2021 9:08 am
|
|
I have a Loni Specter 3/4 in. sitar bar that has 1/4 in. flat.
I really don't know how that compares with others. |
|
|
|
Greg Cutshaw
From:
Corry, PA, USA
|
Posted 13 Aug 2021 9:13 am
|
|
Here's 3 pics of my Dunlop sitar bar. Any bar with a flat edge machined into it should work fine. Diameter is 1.0" and length is 3.75". It's pretty heavy so maybe that helps keep it flat against the strings. Flat spot is 0.375".
 |
|
|
|
Kenny Davis
From:
Great State of Oklahoma
|
Posted 17 Aug 2021 7:43 pm
|
|
Here's an original "Hughey" Sitar Bar. It's 3 1/2" long, diameter is 15/16", the flat spot is 5/16" and the groove is 1/8" Shown next to a Sho~Bud bar.
_________________
Best lyric in a country song: "...One more, Moon..." |
|
|
|
Darrell Criswell
From:
Maryland, USA
|
Posted 24 Aug 2021 7:10 am
|
|
| What is it used for? |
|
|
|
Tommy Auldridge
From:
Maryland, USA
|
Posted 24 Aug 2021 7:41 am sitar bar question
|
|
| With the flat side down(on the strings)it makes the steel sound like a sitar. |
|
|
|
Greg Cutshaw
From:
Corry, PA, USA
|
|
|
|
Larry Dering
From:
Missouri, USA
|
Posted 25 Aug 2021 7:51 am
|
|
| Greg, cool sounding bar if not over used. I recognize that song "if" by Bread. Do you have a chart for it? |
|
|
|
Greg Cutshaw
From:
Corry, PA, USA
|
Posted 25 Aug 2021 12:05 pm
|
|
| Larry, no charts. I have more sound samples somewhere here. |
|
|
|
Larry Dering
From:
Missouri, USA
|
Posted 25 Aug 2021 1:25 pm
|
|
| Thanks Greg. I have just started working on that song. I may throw a few lines in with my sitar bar to see how it goes. Definitely catches the ear with it's tone. |
|
|
|
Gene Tani
From:
Pac NW
|
Posted 30 Aug 2021 3:17 pm
|
|
You can order 1 from Michael Hillman, or ask him about the flat (but I always order by emailing him, NOT thru this website
https://tonebars.com/product-category/sitar-bars/
_________________
- keyless Sonny Jenkins laps stay in tune forever!; Carter PSG
- The secret sauce: polyester sweatpants to buff your picks, cheapo Presonus channel strip for preamp/EQ/compress/limiter, Diet Mountain Dew |
|
|
|
Ron Hogan
From:
Nashville, TN, usa
|
|
|
|
Mark Greenway
From:
Lake Kiowa, Texas
|
Posted 1 Sep 2021 7:11 pm Paul Franklin's Sitar Bar
|
|
From the Paul Franklin Method. Paul Franklin writes: Get as short a piece of 1/8" thick channel aluminum. Have that machinist make a 4" bar and ever so slightly round off all of the sharp edges with a belt sander...Take some 600 sand paper and smooth all of the rough parts and you will have the best and easiest to use sitar bar..It's psychological, put a round bar in the hand and we subliminally use vibrato which is why more downward pressure is applied and that downward pressure causes intonation changes........
Sho-Bud, back in the late 60's made a flat sitar bar that was overkill because it was 1/2 inch thick and very hard to get in tune...It took up too much landscape. I believe some other company started the round bar thing and the concept of using a sitar bar went away because the sound is best when a light touch is used...
I asked my father to make me one as described....Now most of the other session players own one of the type I describe. For a couple of years I started using it and once I played the sitar parts on the Country/Pop hit, "I Hope You Dance"...I started getting calls where they said bring that sitar bar....I believe everyone should own one just in case you get the call.
"I Hope You Dance" Lee Ann Womack https://www.youtube.com/watch?v=DmBSGlXqC4Q
Last edited by Mark Greenway on 1 Sep 2021 7:59 pm; edited 6 times in total |
|
|
|
Mark Greenway
From:
Lake Kiowa, Texas
|
Posted 1 Sep 2021 7:38 pm Sitar bar
|
|
| That Sitar bar lesson is just one of many lessons from the Paul Franklin Method. That course is great for players at any level. It is truly a remarkable wealth of knowledge. |
|
|
|
Ron Pruter
From:
Arizona, USA
|
Posted 16 Oct 2021 6:52 pm
|
|
Mark, Franklin doesn't do a good job describing and the picture gets blurry. Can you better describe what he's talking about. RP
_________________
Emmons SKH Le Grande, '73 Fender P/J bass, Tick tack bass, Regal high strung, USA Nashville 112. |
|
|
|
Mike Bacciarini
From:
Arizona
|
Posted 17 Oct 2021 5:49 am
|
|
Sound Sample..... Norwegian Wood
https://m.youtube.com/watch?v=DJTPtaYtc6s
_________________
MCI Arlington S-10 3+5, George L E-66, BJS & Emmons bars, Fender Stage Lead II 100W 1x12, Fender Satellite SFX, custom FX rack, 1983 Dobro 60D, SX-8 lap steel, Martin D16GT, Ibanez AS73, 1978 Rickenbacker 4000 custom. |
|
|
|
Mark Greenway
From:
Lake Kiowa, Texas
|
Posted 17 Oct 2021 6:04 am
|
|
Take a piece of aluminum like this. It is 1/8 in. thick and 1in. wide. Cut a piece that is 4in. long. Slightly round the edges with a fine grit sand paper.
That is my interpretation of his message.
Last edited by Mark Greenway on 3 Jul 2022 4:17 pm; edited 1 time in total |
|
|
|
Michael Hillman
From:
Boise, Idaho, USA
|
Posted 2 Jul 2022 2:38 pm Very interesting discussion-
|
|
I appreciate the commentary on this thread. Forum member Kenny Siegal brought this discussion to my attention- I’m pursuing making an aluminum sitar bar just as Paul Franklin describes - in numbers. After the prototype is tested, I will post details in the new products section -assuming it works as well as we believe it will.
_________________
Two Spector 5 string basses, Martin D-18, Taylor 812CE, 1996’Epiphone Sheraton, 1944 Epiphone Zenith, a killer Luttrell 6 string resophonic, 1932 Model 56 Dobro, Beard Model E, Martin Soprano Uke, 10 string 1953 Alkire Eharp, Peavey Nashville 112, Fender Bassman, Fender 75 watt Rumble, and a Fender 100 watt Rumble. |
|
|
|
