How much do power amps affect tone?

George Kimery · From: Limestone, TN, USA

I've had different power amps over the years and never really thought much about how they affect tone.I always thought that the tone was all in the pre-amp section. I have my Evans stereo pre-amp run through the RCA tape inputs on my Stereo Steel power amp section. Sounds good to me. If I had a separate, dedicated power amp would there be a noticeable difference in tone?.

Larry Dering · From: Missouri, USA

George, just from my own experience, it does matter. I tried a Peavey DPC 750 using the Profex II and a Peavey tube preamp and it sounded sterile. I subbed in a couple other stereo power amps and the same results. However the Stewart world power amp sounds good to my ears. Not very scientific but using what I had and same speaker cabinets, both 115E Peavey.

Earnest Bovine · From: Los Angeles CA USA

For my steel, the Mosvalve power amps sound better than the others I've tried.

Donny Hinson · From: Glen Burnie, Md. U.S.A.

Most power amps are designed to have a relatively flat response curve. They do have tonal differences, naturally, due to design quality and the components used. But those differences are likely far less than the differences made by preamps (and their settings), speakers, and the speaker enclosures themselves.

It's also good to keep in mind that musical instrument amplifiers are pretty far from being "high-fidelity devices", due to their design and market constraints.

Jerry Overstreet · From: Louisville Ky

Steve Lipsey · From: Portland, Oregon, USA

Uh....tubes!
Preamp tube response warms things up (like a Sarno Black Box) but final amp tube response is a treat...I learned that from standing in front of a Marshall stack - once the master volume got past 8 or so it had a magical effect on tone.

And I loved my Milkman Pedal Steel Mini (40 watts) even more than my full-size Pedal Steel amp (85 watts)..with fairly frequent chances to play it dimed it really sang...not the totally clean tone some seek, but a rich, warm sustain...

That's why folks are using smaller tube amps for so many things now...finally learned to make them sing at reasonable volume...

I'm not sure that is what you are asking about, but that's where I'm at. Now using a Milkman "The Amp" and sort of missing the "goes to 11" tone, but fitting it on my pedal board has gotten more important as the years progress..
_________________
https://www.lostsailorspdx.com
Williams S10s, Milkman Pedal Steel Mini & "The Amp"
Ben Bonham Resos, 1954 Oahu Diana, 1936 Oahu Parlor

Brett Lanier · From: Hermitage, TN

I used to have a McIntosh mc50 that sounded great. It's the smallest mono version of McIntosh's early transistor amps, but still very loud. I did some comparing with other amps and it was always the winner for steel... I was able to compare it to the power amp in my twin by taking a line out, into the McIntosh, then back into the 15" speaker in the combo. Even at 50 watts it was louder and more robust sounding than the power section of the twin. At home I would often play straight into the McIntosh power amp with no preamp. It wasn't very loud but it was a completely quite signal with a very well balanced eq.

Jack Stoner · From: Kansas City, MO

Back when I was into "Stereo" for steel I tried several power amps including Peavey DPC 750 and 1000 and several other "PA" type amps and they all seemed "sterile". Very flat and "Hi Fi". I got a MosValve 500 power amp and there was the tone.

Gabriel Edell · From: Hamilton, Ontario

David Spires · From: Millersport, OH

Everything affects everything...

But, I've heard Paul Franklin though Nashville 400s, a Walker Stereo Steel, Little Walter, and (although noticably not HIS sound) a Line 6 POD 2.0, and...

Paul always sounded like Paul.

The ideas, musicality, and execution win every time.

(as I try different gear today, looking for the elusive magic, not listening to my own advice...)

Sincerely,

David Spires
_________________
2021 MSA Legend XL 10&7; Asher Electro-Hawaiian Junior Lap Steel; '79 OMI Dobro 66 w/ Scheerhorn cone and setup; '64 Hand-wired Re-issue Fender Princeton Reverb

Steve Hinson · From: Hendersonville Tn USA

+1 for the Mosvalve!

I use the Mosvalve with either the Mesa Boogie Studio Preamp or the Evans single space preamp bout every day...
closest thing I've found to a Twin...with extra headroom...

SH

Sandy Inglis · From: Christchurch New Zealand

Hi George, Be aware that some RCA Tape inputs can be tone compensated to roll of the pre-emphasis of the old tape players. I'm not sure that that will be the case now but it's something to think about. You are better going into a line input if you can.
( I used to work in Radio & TV a long time ago).
Sandy
_________________
01'Zumsteel D10 9+9; Sho Bud D10 SuperPro; 6 String Lap Steel (Homemade); Peavey Nashville 1000; Fender Deluxe 85;
1968 Gibson SG; Taylor 710 CE; Encore Tele Copy; Peterson Tuner; HIWATT T40 C 40W/20W Combo

Godfrey Arthur · From: 3rd Rock

Even if you used the exact same model of power amp for your extension, there would be a tonal difference just because that's the nature of things. Not unless you went through 2 dozen of the same model to match the tone of the 1st amp would you get something "ballpark."

But as others chimed, using McIntosh amps, the power amp depending on build will all sound different.

Not only does the amp make a difference, the transformers in them make a difference in tone which is why you have companies like Mercury Magnetics making alternatives.

Bass players back in the 70's used to use a Phase Linear power amp because there was a circuit in one of those models that pulled the speaker back to "0" to get ready for the next note making for a tighter less muddy response because the speaker's cone was electronically pulled back rather than wait for it to spring back on its own... just to give an example of how design is varied. Imagine using such an amp for steel with the complexities of chord clusters and attack variations, if this type amp would work well for steel.

_________________
ShoBud The Pro 1
YES it's my REAL NAME!
Ezekiel 33:7

Ian Rae · From: Redditch, England

No amplifier is inherently flat - it has to be engineered that way. For hi-fi it's a no-brainer, but for musical instruments (including the voice) it makes sense to tailor the response to its end use.

Having said that, the Telonics power amp I use does claim a flat response from 20Hz to 20kHz just like a typical hi-fi.
_________________
Make sleeping dogs tell the truth!
Homebuilt keyless U12 7x5, Excel keyless U12 8x8, Williams keyless U12 7x8, Telonics rack and 15" cabs

Erv Niehaus · From: Litchfield, MN, USA

I have a MosValve amp in my rack. Along with a couple of other TubeWorks units: a 12 spring reverb and a Blue Tube preamp. Very Happy

Erv

Bob Hoffnar · From: Austin, Tx

When I was into separate power amps I found the difference to be significant. The VHT 2/50/2 was my favorite. Really amazing sounding. I just got tired of hauling around all that stuff and moved on to different amp set ups.

There seems to be a difference in the class D amps I hear in different powered speakers and amps too. Some sound pixelated or maybe like florescent lights compared to incandescent to me. Others sound even and smooth. Those differences are pretty subtle though.
_________________
Bob

George Kimery · From: Limestone, TN, USA

When I got the Evans pre-amp, I had to have a power amp. I bought a Stewart 2.0 from a local steel player that he wasn't using any more. It was very heavy and wouldn't fit into my rack case. I had my Stereo Steel system at the time and during an unrelated conversation with GD Walker, I mentioned the Stewart. He said I could use the RCA inputs on the Stereo Steel as my power amp. So I made up two short adapter cords with RCA plugs on one end and 1/4" mono plugs on the other ends. The Stereo Steel combo amp was never designed to be a power amp so there are no 1/4" direct in jacks, only the RCA jacks which are convience jacks for hooking up a tape player.
I sold the Stewart so I don't have it to compare to the Stereo Steel. I have never noticed any problem with the sound I'm getting with the Stereo Steel.

I'm mostly using my SE 200 combo amp on gigs now.
Should I decide to sell my Stereo Steel, then I would need a power amp. From the feedback, it looks like MosValve would be a good way to go.

As always, thanks to all of you that have responded. You have been very helpful.

Jerry Overstreet · From: Louisville Ky

I have stereo MosValves 962 and a 942. The biggest issue with TubeWorks/MosValve products is the control pots. They get noisy and sometimes cut out altogether. Just FYI.

Otherwise, they are heavy. The 500 watter weighs in at about 32#. The 2 sp. 160 watt a little bit less, but bulky. They also made one of these in a one sp. rack size.

They sold out to Genz-Benz and labeled them TubeWorks instead of MosValve. The 500 watt amp is a model 1500 in the GB line.

George Kimery · From: Limestone, TN, USA

Jerry, I had one of those heavy TubeWorks power amps. I thought from the name, I had a tube power amp but I remember being corrected on the forum. I had a pre-amp like Herby Wallace was using. I am think it was a MosValve, but I'm not sure, it was a long time ago. I had forgotten about the weight of that TubeWorks power amp. Thanks for reminding me. I will just keep what I have. The combination of the Evans and Stereo Steel is a sweet set-up and I can go from one to the other by just moving the guitar cord.

Larry Dering · From: Missouri, USA

Jerry is right on the pots. Plus they have extra long connection legs wich are uncommon and hard to source. I spoke to one of the Tube Works engineers who had the pots but they were pricy.

Erv Niehaus · From: Litchfield, MN, USA

If I remember, the TubeWorks pots were smaller than standard in size.
I haven't dealt with them of late but Genz Benz were good to get parts through for the TubeWorks stuff.
I bought my original TubWorks stuff through Emmons, they sold them.
The Blue Tube pre-amp is hard to beat. Very Happy

Erv

Jerry Overstreet · From: Louisville Ky

TubeWorks/Mosvalve pots are dime sized 16mm long leg vertical PC mount type. I did not go to GB because I wanted enough to do all of my units.
smallbear-electronics.mybigcommerce.com/ is where I got mine, but I had to cut down the legs on all of them to fit these amps and units.

I ordered about 30 of them from this co. They were just over a buck apiece and he has them in all both types.

I used a dremel to narrow the legs to go far enough down in the board.

Kenneth Kotsay · From: Davie/Ft Lauderdale, Florida

I have the Peavey DPC 1000 and a Mackie FR Series 1400i power amp, both satisfy my needs, I find no problems with both, tone sounds awesome.

George Redmon · From: Muskegon & Detroit Michigan.

Every single word that Steve Lipsey said!

There's something about sitting in front of a 68 Plexi, through a Marshall stack, with just the right amount of compression, and an old Goodrich pot pedal, and the steel of your choice, to make you feel all warm inside and giggly like a school girl.

Forum Index > Electronics		Next oldest topic :: Next newest topic