| Author |
Topic: Unfreezing frozen steel leg clutches? |
T. C. Furlong
From:
Lake County, Illinois, USA
|
Posted 11 Feb 2006 11:52 am |
|
I just acquired an old Emmons P/P and three of the legs had their clutches frozen. I have a pipe vise built into my workmate and put the heavy wrench on the adjustment collar but these babies are totally locked up. I thought of penetrating oil but then I thought it might foul up the porous part inside the clutch. I can always buy new clutch parts but maybe here on the forum might have the wisdom. Thanks in advance.
TC |
|
|
 |
Jerry Roller
From:
Van Buren, Arkansas USA
|
Posted 11 Feb 2006 12:01 pm
|
|
TC, you won't hurt anything using WD40 or some other penetrating oil. Just put a good amount around the tightening collar and let it soak until you can break it loose. All there is in the clutch is The steel leg, aluminum or steel collar, a brass bevelled washer and a rubber compression washer. Let it soak good to avoid having to tighten a vise very tight, You should put the threaded lug in the vise and wrap some protection on it first. Don't put the hollow part of the leg in a vise. I'm sure you know all this already but a reminder can't hurt.
Jerry[This message was edited by Jerry Roller on 11 February 2006 at 12:03 PM.] |
|
|
|
R.C. Vick
From:
Moss Point, Ms., USA
|
Posted 11 Feb 2006 12:29 pm
|
|
| T.C. If the WD-40 isnt enough (and it wont be), dont give up yet. I researched several penetrating oils after Katrina to try to help co-workers who were saving belongings. I settled on Gibb's penetrating oil and I am now a firm believer. I ordered a few cases and they lasted a day for cost. I have now become a distributor (basically in name to have it on hand) If it can be freed up, it will do it! Check it out on a search engine, then email me if I can help. Thanks. |
|
|
|
T. C. Furlong
From:
Lake County, Illinois, USA
|
Posted 11 Feb 2006 12:34 pm
|
|
Hi Jerry, Thanks for the advise. I opened up the one good clutch and the compression ring looks to be phenolic. I think I remember that phenolic is porous. That's why I was being cautious. I was thinking that if the phenolic ring gets soaked with oil, it might not grab when compressed.
Newer clutches have a brass washer and a hard plastic compression ring that has a split in it. I guess it doesn't matter that much but I'd like to keep things original.
TC |
|
|
|
T. C. Furlong
From:
Lake County, Illinois, USA
|
Posted 11 Feb 2006 12:37 pm
|
|
R.C. Thanks very much. I will look for Gibbs. And good work helping out your neighbors!
T.C. |
|
|
|
Jim Bob Sedgwick
From:
Clinton, Missouri USA
|
Posted 11 Feb 2006 4:45 pm
|
|
Never Ever Force it. I just go get a BIGGER hammer.  |
|
|
|
Bill Hamner
From:
Hueytown,AL USA
|
Posted 12 Feb 2006 4:04 am
|
|
T.C.,
If these are OEM Emmons legs the Collars are aluminum. Just a small amount of heat will do wonders. The expansion rate difference between the steel legs and the aluminum collar is considerable and you might find that a heat gun very similar to a hair dryer will do the job with out damaging any of the parts. Just carefully heat the collar and you might find they become only finger tight.
Another option.... Preheat your oven to approximately 200 degress, remove the rubber tips on the bottom end of the legs and place the entire leg in the oven for a few minutes
(3 to 5 min. may be sufficient). With gloves on you may be able to turn the collars by hand if the threads are not galled. Another neat trick that may help...Have a candle nearby when you heat the collar and apply it to the joint while hot. This should allow some melted wax to seep into the affected area. This works well on seized pipe plugs also.
Bill[This message was edited by Bill Hamner on 12 February 2006 at 04:41 AM.] |
|
|
|
T. C. Furlong
From:
Lake County, Illinois, USA
|
Posted 12 Feb 2006 5:42 am
|
|
Bill - The legs are OEM Emmons but they are from a '66/'67 so they have the steel collars just like an Atlas mic stand. I have a paint stripping heat gun so I may try heating the collar anyway to see what happens. Thanks very much!
Jim Bob -  |
|
|
|
Rick Garrett
From:
Tyler, Texas
|
Posted 12 Feb 2006 6:28 am
|
|
Hey TC, I had the same problem on my dads Fender Stringmaster. It had been setting in a museum for years and there was no way to get the leg clutch's loose. I stood them up against the work bench (Upside down) and then soaked them good with WD40. next morning I had the loose enough to move just a little bit each way. I soaked them again and the next day they freed up. Hope this helps. Didn't hurt the clutch parts either.
Rick |
|
|
|
Stephen Gregory
|
Posted 13 Feb 2006 1:38 pm
|
|
| Unfreezing.... Is that anything like thawing? |
|
|
|
Mark Herrick
From:
Bakersfield, CA
|
Posted 14 Feb 2006 8:44 am
|
|
I'd try the penetrating oil overnight and then whack the sides of the collars a few times with a hammer, using a block of wood to prevent damage to the metal. The shock of the hammer blows should loosen the threads...
------------------
|
|
|
|
