| Visit Our Catalog at SteelGuitarShopper.com |

Post new topic 1940 Ricki 8 string needing neck repair
Reply to topic
Author Topic:  1940 Ricki 8 string needing neck repair
Paul Atkinson

 

From:
Ontario, Canada
Post  Posted 15 May 2019 2:20 pm    
Reply with quote

Long story short, I finally found and bought my holy grail, a 1940 Rickebacher 8 string bakelite in near mint condition. And you guessed it. It showed up with a broken neck. (I think I’m still in shock.).

I have two questions.

Can anyone recommend someone who has experience repairing bakelite Ricki necks and does meticulous work?

I’ve read some old forum postings and several years ago members were recommending Acraglas to repair bakelite necks. Is there anything better at this point and time?

I’d appreciate any suggestions you might have. I want to make sure this rare piece of Ricki history lasts another 80 years.


View user's profile Send private message Send e-mail
Paul Atkinson

 

From:
Ontario, Canada
Post  Posted 15 May 2019 2:31 pm     Here's the before picture
Reply with quote

That is before the shipping company used it as a football.


View user's profile Send private message Send e-mail
Michael Deering

 

From:
Arizona, USA
Post  Posted 15 May 2019 2:44 pm     RICKENBACHER RESTORATION pain
Reply with quote

Sorry to see your Rickenbacher neck tragedy. I own 2 rics and this is my one yikes moment.
Bet you get some help here on the forum soon.
View user's profile Send private message Send e-mail
David Matzenik


From:
Cairns, on the Coral Sea
Post  Posted 15 May 2019 3:04 pm    
Reply with quote

For bakelite Rickenbacher repairs, I used West System epoxy dyed with black epoxy dye from West Marine. For chip fill, I made the epoxy into a thick paste with Cabosil filler, a powdered silica. If anything, it was little too shiny at first, but as the years have passed, its hard to see the repairs.

All that being said, when it comes to a broken neck, I would say it will require an unobtrusive tenon to support any glue joint. Perhaps stainless steel.
_________________
Don't go in the water after lunch. You'll get a cramp and drown. - Mother.
View user's profile Send private message Send e-mail
Michael Brebes

 

From:
Northridge CA
Post  Posted 16 May 2019 7:02 am    
Reply with quote

First, it looks like removing the screw in the back of the body will release the remaining part of the neck attached to the body. As someone else mentioned, I would not count on the bakelite repair to hold the neck break intact. I would drill out a hole between the two pieces and install some kind of a steel rod, glued into both pieces, including the bakelite repair compound as the two are being mated together. Then clamp the two lengthwise until the whole assembly dries. Probably to insure proper drilling of the hole, I would clamp the two pieces together, then drill from the end of the neck (where it enters the body) all the way past the break. You might need to use a special long bit for this, but it would be the most accurate.
_________________
Michael Brebes
Instrument/amp/ pickup repair
MSA D10 Classic/Rickenbacher B6/
Dickerson MOTS/Dobro D32 Hawaiian/
Goldtone Paul Beard Reso

Mesa Boogie Studio Pre/Hafler 3000
RP1/MPX100
View user's profile Send private message Send e-mail
Michael Brebes

 

From:
Northridge CA
Post  Posted 16 May 2019 7:17 am    
Reply with quote

Reexamining the pictures, because of the screw attaching the neck, you might not be able to drill a hole from the end of the neck. You might have to go with at least an oversized hole in one piece with a tighter hole on the other. That way you could glue the rod in place in the tight hole then extra glue in the sloppy hole as you mate the two pieces together.
_________________
Michael Brebes
Instrument/amp/ pickup repair
MSA D10 Classic/Rickenbacher B6/
Dickerson MOTS/Dobro D32 Hawaiian/
Goldtone Paul Beard Reso

Mesa Boogie Studio Pre/Hafler 3000
RP1/MPX100


Last edited by Michael Brebes on 18 May 2019 6:06 am; edited 1 time in total
View user's profile Send private message Send e-mail
Scott Duckworth


From:
Etowah, TN Western Foothills of the Smokies
Post  Posted 16 May 2019 7:20 am    
Reply with quote

Might be possible to use a piece of flat stock steel and drill a hole that screw would go through. Would take someone who could mill the slot for the flat stock correctly so it fits tight.

Good luck, sorry for your misfortune.
_________________
Amateur Radio Operator NA4IT (Extra)
http://www.qsl.net/na4it

I may, in fact, be nuts. However, I am screwed onto the right bolt... Jesus!
View user's profile Send private message Send e-mail Visit poster's website
Eric Einarsson

 

From:
Los Gatos, California, USA
Post  Posted 16 May 2019 7:28 am    
Reply with quote

Or, massaging Micheal Brebes hole and peg repair, drill two smaller holes, one on each side of the screw.

Absolutely clamp the break together before drilling to ensure the alignment.

Good luck with your repair.

Eric Einarsson
View user's profile Send private message Send e-mail
Steve Wilson


From:
Morgan Hill, California, USA
Post  Posted 16 May 2019 10:45 am     My Two Cents
Reply with quote

I repaired a prewar B6 for a customer with a break just like yours. I used only Acraglas(Red Box)with the supplied black dye. I did not use any other reinforcement. The trick I was told was to get a jig set up ahead of time to bring the two pieces into proper alignment and able to force it tightly together. You have to work quickly because the Acraglas sets up very quickly, and gets very hot. I did not touch it for three days to allow it to cure properly. The break on mine was so clean it did not require any drop fills, I just repainted the white fret marker and called it a day.That was 10 years ago and I am told the break is still solid.I took some pics, but I cannot find them now. YMMV
[/url]


Last edited by Steve Wilson on 16 May 2019 11:07 am; edited 1 time in total
View user's profile Send private message Send e-mail
Steve Wilson


From:
Morgan Hill, California, USA
Post  Posted 16 May 2019 11:05 am    
Reply with quote

Here is a picture of the jig I used. It took about an hour to get it set up perfectly. Once I was happy with it I had to work quickly,
View user's profile Send private message Send e-mail
Jack Hanson


From:
San Luis Valley, USA
Post  Posted 16 May 2019 1:25 pm    
Reply with quote

Before going off topic here, my condolences to Paul for what must have been a truly heart-breaking experience. I can hardly imagine the shock upon opening the box and discovering the damage. A tragic loss of a rare and exceptional instrument. Hopefully it can be repaired to your satisfaction.

My sincere thanks to Steve for sharing the photos above. I need to make a jig to repair a neck from a Duolian with a severed headstock. I'd been contemplating how best to proceed, and your jig has started the cogs and gears and wheels turning between my ears. Looks like a similar approach would work for me.
View user's profile Send private message Send e-mail
Bill Groner


From:
QUAKERTOWN, PA
Post  Posted 16 May 2019 3:27 pm    
Reply with quote

YUP, that Steve is a right smart feller. He comes up with some pretty neat stuff.
_________________
Currently own, 6 Groner-tone lap steels, one 1953 Alamo Lap steel, Roland Cube, Fender Champion 40
View user's profile Send private message Send e-mail
Steve Wilson


From:
Morgan Hill, California, USA
Post  Posted 16 May 2019 10:54 pm    
Reply with quote

Thanks Bill and Jack!
When I looked at the date on the photos it was actually 18 years ago! How time flies.

As I recall I used blue tape on the fretboard side of the crack so I could hinge it open without moving the clamps to apply the Acraglass, and the tape also kept the Acraglass from running onto the jig and gluing it permanently there. I had seen a very fancy jig a forum member (maybe from Indiana) had made, I tried to contact him to see if I could borrow it but it didn't work out. Good luck!
View user's profile Send private message Send e-mail
Bill Groner


From:
QUAKERTOWN, PA
Post  Posted 17 May 2019 12:18 am    
Reply with quote

I think I see some wax paper under the neck as well. That stuff works great as a release agent.
_________________
Currently own, 6 Groner-tone lap steels, one 1953 Alamo Lap steel, Roland Cube, Fender Champion 40
View user's profile Send private message Send e-mail
Steve Wilson


From:
Morgan Hill, California, USA
Post  Posted 17 May 2019 1:06 am    
Reply with quote

Yes indeed.I forgot about the waxed paper...your eyes are better than my memory
View user's profile Send private message Send e-mail
Tom Snook

 

From:
Ft. Lauderdale, Florida, USA
Post  Posted 17 May 2019 1:56 am    
Reply with quote

Would love to see pics as the repair goes along,might could benefit some poor soul in the future.
ALOHA
_________________
I wanna go back to my little grass shack........
View user's profile Send private message Send e-mail
Michael Brebes

 

From:
Northridge CA
Post  Posted 18 May 2019 6:11 am    
Reply with quote

That's nice to know that the Acraglas will hold the break without any added support. That makes it a much easier repair.
_________________
Michael Brebes
Instrument/amp/ pickup repair
MSA D10 Classic/Rickenbacher B6/
Dickerson MOTS/Dobro D32 Hawaiian/
Goldtone Paul Beard Reso

Mesa Boogie Studio Pre/Hafler 3000
RP1/MPX100
View user's profile Send private message Send e-mail
David DeLoach


From:
Tennessee, USA
Post  Posted 18 May 2019 6:28 am    
Reply with quote

Last year I bought an early '40's Richenbacher that had a neck repair done on it at some point. I'm not sure exactly how it was done, but there are two screws showing on the underside, and you can see the lines between the 10th and 11th fret are bit brighter.

Regardless of the aesthetics, it plays and sounds awesome!








View user's profile Send private message Send e-mail Visit poster's website
Paul Atkinson

 

From:
Ontario, Canada
Post  Posted 21 May 2019 6:27 pm    
Reply with quote

Thanks for all the input guys. I'm not sure if I'm going to attempt it on my own or get someone who's already done a few to do it.
View user's profile Send private message Send e-mail
Bill Creller

 

From:
Saginaw, Michigan, USA (deceased)
Post  Posted 28 May 2019 3:52 pm    
Reply with quote

I recently did a neck/headstock repair on a 30s 7-string bakelite for Bobby Ingano. Luckily, it broke on a long flat angle, with lots of area for the epoxy to mend it. It broke just between the tuners and the nut. He told me yesterday that it sounds great as ever, so that's good news !! Very Happy
View user's profile Send private message Send e-mail

All times are GMT - 8 Hours
Jump to:  
Please review our Forum Rules and Policies
Our Online Catalog
Strings, CDs, instruction, and steel guitar accessories
www.SteelGuitarShopper.com

The Steel Guitar Forum
148 S. Cloverdale Blvd.
Cloverdale, CA 95425 USA

Click Here to Send a Donation

Email SteelGuitarForum@gmail.com for technical support.


BIAB Styles
Ray Price Shuffles for Band-in-a-Box
by Jim Baron