| Visit Our Catalog at SteelGuitarShopper.com |

Post new topic A solution to legs slipping
Goto page 1, 2  Next
Reply to topic
Author Topic:  A solution to legs slipping
Mike Perlowin


From:
Los Angeles CA
Post  Posted 23 Feb 2019 1:47 pm    
Reply with quote

The solution is to insert 5/8 inch O rings between the clutch and the rubber foot. After these pictures were taken I covered the rings with black duct tape. (Black duct tape sounds better.Laughing)




_________________
Please visit my web site and Soundcloud page and listen to the music posted there.
http://www.mikeperlowin.com http://soundcloud.com/mike-perlowin
View user's profile Send private message Send e-mail Visit poster's website
Donny Hinson

 

From:
Glen Burnie, Md. U.S.A.
Post  Posted 23 Feb 2019 5:05 pm    
Reply with quote

That might be okay as an ersatz fix. But if it were mine, I'd repair the clutches so they'd work like they're supposed to. That way, you retain the adjustability feature. Cool
View user's profile Send private message Send e-mail
Doug Earnest


From:
Branson, MO USA
Post  Posted 23 Feb 2019 5:25 pm    
Reply with quote

Donny Hinson, how would you go about the repair?
View user's profile Send private message Send e-mail
Bob Carlucci

 

From:
Candor, New York, USA
Post  Posted 23 Feb 2019 5:25 pm    
Reply with quote

on my road guitars it was duct tape.. when that stopped working, new duct tape over the old smeared duct tape... Then more duct tape......

If it slipped during a set, i would run out to a table, grab an ash tray, put a rag in it, or a few folded up napkins and stick it under the leg... good as new!
_________________
I'm over the hill and hittin'rocks on the way down!

no gear list for me.. you don't have the time......
View user's profile Send private message
Mike Perlowin


From:
Los Angeles CA
Post  Posted 23 Feb 2019 8:40 pm    
Reply with quote

Donny Hinson wrote:
..if it were mine, I'd repair the clutches so they'd work like they're supposed to.


Hi Donnie. We (Jim Palenscar) tried that and it worked for a while, but eventually the clutch started slipping again.
_________________
Please visit my web site and Soundcloud page and listen to the music posted there.
http://www.mikeperlowin.com http://soundcloud.com/mike-perlowin
View user's profile Send private message Send e-mail Visit poster's website
Jerry Jones


From:
Franklin, Tenn.
Post  Posted 24 Feb 2019 7:23 am    
Reply with quote

I've seen it suggested that you can insert a short wooden dowel inside the large tube to keep the smaller tube set at one length. Haven't tried it but I'm sure it would work.
_________________
Jerry Jones
View user's profile Send private message Send e-mail
Jack Hanson


From:
San Luis Valley, USA
Post  Posted 24 Feb 2019 8:27 am    
Reply with quote

Some years back I purchased a Studio Deluxe (basically a Champ with legs) that had been stripped of all its electronics but was otherwise intact. None if its three legs held; they all slipped. I took the legs apart and cleaned all the interior parts with a mild solvent (probably either naptha or denatured alcohol -- don't recall exactly) and all three have worked flawlessly ever since. It's worth a try.
View user's profile Send private message Send e-mail
Jack Stoner


From:
Kansas City, MO
Post  Posted 24 Feb 2019 9:40 am    
Reply with quote

The back legs on my Franklin were slipping. They were the original legs from late 81. I took them apart and cleaned the insert, even reversed the insert. That helped for a short while and then they started slipping again. I finally bought two repair kits and inserted the new parts but used the old "nuts" as the new ones are bigger and chrome plated. That didn't work but using the new kit parts with the new chrome plated nut did. That was almost a year ago and no more legs slipping.
View user's profile Send private message Send e-mail
Fred Treece


From:
California, USA
Post  Posted 24 Feb 2019 10:01 am    
Reply with quote

Jerry Jones wrote:
I've seen it suggested that you can insert a short wooden dowel inside the large tube to keep the smaller tube set at one length. Haven't tried it but I'm sure it would work.

This is more or less how Doug E. set up the front leg extensions on my Stage One. Works perfectly.
View user's profile Send private message Send e-mail
Butch Mullen

 

From:
North Carolina, USA 28681
Post  Posted 24 Feb 2019 1:05 pm    
Reply with quote

I use a small hose clamp around the small part of the leg under the clutch. Works good and still adjustable.
View user's profile Send private message Send e-mail
Bob Carlucci

 

From:
Candor, New York, USA
Post  Posted 24 Feb 2019 1:11 pm    
Reply with quote

Butch Mullen wrote:
I use a small hose clamp around the small part of the leg under the clutch. Works good and still adjustable.

Good idea there...
_________________
I'm over the hill and hittin'rocks on the way down!

no gear list for me.. you don't have the time......
View user's profile Send private message
Drew Pierce

 

From:
Arkansas, USA
Post  Posted 24 Feb 2019 2:35 pm    
Reply with quote

I guess I'm lucky. I've been playing all kinds of guitars for close to forty years and never had that problem. If they slipped, it was usually because I didn't have them quite tight enough. Biggest problem is sometimes I over-tightened to where they were a bear to loosen for small adjustments for an uneven floor.
_________________
Drew Pierce
Emmons D10 Fatback, S10 bolt-on, Zum D10, Evans RE500, Hilton volume and delay pedals.
View user's profile Send private message Send e-mail
Ricky Davis


From:
Bertram, Texas USA
Post  Posted 24 Feb 2019 4:35 pm    
Reply with quote

Well I've been restoring pedal steels now for over 20 years and so that is at least 100 of them...and almost every one had a leg slipping and HERE IS WHY>
Over tightening.
Here's how I fixed hundreds of legs; yes EVERY SINGLE ONE OF THEM and now they don't slip after I fixed.
After OVER-tightening; there gets a build up of small metal shavings in the threads and that is what needs to be cleaned out. So take the tightener off...and with 3 and 1 oil or any very light oil..>gun oil; Sewing machine oil..etc...
Oil up a rag and clean all threads on inside of tightener and threads on the leg bar.
Put back together; make sure both fittings are on the small diameter bar, that you are actually tightening to not move; as metal fitting up against leg thread and plastic fitting against it...and put tightener back down...slowly screwing back to leg making sure it threads straight....and tighten slowly then loosen; then tighten; couple of times...then normal tighten and you're good to go.
Ricky
_________________
Ricky Davis
Email Ricky: sshawaiian2362@gmail.com
View user's profile Send private message Send e-mail Visit poster's website
Donny Hinson

 

From:
Glen Burnie, Md. U.S.A.
Post  Posted 25 Feb 2019 12:28 pm    
Reply with quote

Jack has the right idea. Clean the parts in acetone or alcohol, and then reassemble properly ! Most all the ones I've seen that won't work right have been assembled wrong. The cone-edge (beveled edge) of the jam washer must be against the split ring!

And if you don't know what you're doing, never oil them or take them apart. Truth is, most of them work as intended...until somebody tries to fix them or make the work better.
View user's profile Send private message Send e-mail
Al Evans


From:
Austin, Texas, USA
Post  Posted 18 Mar 2019 5:26 am    
Reply with quote

Ricky Davis wrote:
Well I've been restoring pedal steels now for over 20 years and so that is at least 100 of them...and almost every one had a leg slipping and HERE IS WHY>
Over tightening.
Here's how I fixed hundreds of legs; yes EVERY SINGLE ONE OF THEM and now they don't slip after I fixed.
After OVER-tightening; there gets a build up of small metal shavings in the threads and that is what needs to be cleaned out. So take the tightener off...and with 3 and 1 oil or any very light oil..>gun oil; Sewing machine oil..etc...
Oil up a rag and clean all threads on inside of tightener and threads on the leg bar.
Put back together; make sure both fittings are on the small diameter bar, that you are actually tightening to not move; as metal fitting up against leg thread and plastic fitting against it...and put tightener back down...slowly screwing back to leg making sure it threads straight....and tighten slowly then loosen; then tighten; couple of times...then normal tighten and you're good to go.
Ricky


Thank you for this tip! I have had a slipping leg on my old MSA ever since I got it, and this seems to have cured the problem.

--Al Evans
_________________
2018 MSA Legend, 2018 ZumSteel Encore, 2015 Mullen G2, G&L S-500, G&L ASAT, G&L LB-100, Godin A4 Fretless, Kinscherff High Noon
View user's profile Send private message
Bobby D. Jones

 

From:
West Virginia, USA
Post  Posted 18 Mar 2019 9:56 am     A solution for legs slipping
Reply with quote

I gigged a 1974 MSA S10 that had legs that would not hold secure. I cleaned and worked on all 4 clutches. They held better, But I could not trust them.

I took one of the legs to a hardware store and bought 4 dowel rod that fit snug in the small leg tube. Adjusted the legs level. Removed the rubber foot, Inserted a dowel rod in each leg till it contacted the thread insert that screws in the guitar body, At top of leg. Cut the dowel rod even with the leg inter sleeve. Reinstalled the rubber feet. On the 2 front legs I hot glued the dowel rods in the legs, So they could not move. Then drilled the holes for the cross bolts that attach the pedal bar. Nothing visible on outside of legs.
I can adjust either rear leg to fit an uneven floor and use the clutch to hold the leg. If is slips it just stops when it hits the dowel rod.

I now gig a GFI with solid aluminum legs, The back legs screw adjust. No leg worries now.
View user's profile Send private message Send e-mail
Jim Fogarty


From:
Phila, Pa, USA
Post  Posted 12 Mar 2021 5:19 pm    
Reply with quote

Ricky Davis wrote:
Well I've been restoring pedal steels now for over 20 years and so that is at least 100 of them...and almost every one had a leg slipping and HERE IS WHY>
Over tightening.
Here's how I fixed hundreds of legs; yes EVERY SINGLE ONE OF THEM and now they don't slip after I fixed.
After OVER-tightening; there gets a build up of small metal shavings in the threads and that is what needs to be cleaned out. So take the tightener off...and with 3 and 1 oil or any very light oil..>gun oil; Sewing machine oil..etc...
Oil up a rag and clean all threads on inside of tightener and threads on the leg bar.
Put back together; make sure both fittings are on the small diameter bar, that you are actually tightening to not move; as metal fitting up against leg thread and plastic fitting against it...and put tightener back down...slowly screwing back to leg making sure it threads straight....and tighten slowly then loosen; then tighten; couple of times...then normal tighten and you're good to go.
Ricky


Thanks for this. I have a '52 Fender Dual 8 steel where all three legs were slipping bad. This fixed 2 of them. Unfortunately the 3rd leg, which seems to be of a different make, is still slipping. Have you ever come across one where that method DIDN'T work, Ricky? If so.......just buy a new one??

Still.....at the evry least, you saved me @$80!
View user's profile Send private message Send e-mail Visit poster's website
Scott Denniston


From:
Hahns Peak, Colorado, USA
Post  Posted 12 Mar 2021 6:28 pm    
Reply with quote

I did the dowel trick on my Sho-Bud years ago. It works well enough I forgot it was in there until I read this thread.
View user's profile Send private message Send e-mail
Jim Fogarty


From:
Phila, Pa, USA
Post  Posted 12 Mar 2021 6:42 pm    
Reply with quote

Scott Denniston wrote:
I did the dowel trick on my Sho-Bud years ago. It works well enough I forgot it was in there until I read this thread.


I would absolutely do that with pedal steel, but with my console lap, I need to set it up differently, sitting or standing.
View user's profile Send private message Send e-mail Visit poster's website
Gene Tani


From:
Pac NW
Post  Posted 13 Mar 2021 4:20 am    
Reply with quote

Usually when a leg slips, I take the clutch apart andsee white grease all over everything.

When you clean the clutch including cleaning lower leg with rubbing alcohol or citrus cleaner (goo gone), the plastic and metal locking rings in the clutch have beveled faces that need to go together.

I've used the dowels, and 1/2" inner diameter PVC pipe from Home Depot

[forgot to mention] sometimes the gap in the reddish plastic lock ring is too narrow and needs to be widened a bit with sandpaper, and sometimes it helps to roughen the insiden of it with sandpaper.
_________________
- keyless Sonny Jenkins laps stay in tune forever!; Carter PSG
- The secret sauce: polyester sweatpants to buff your picks, cheapo Presonus channel strip for preamp/EQ/compress/limiter, Diet Mountain Dew
View user's profile Send private message Send e-mail
Randy Cook

 

From:
Mechanicsville, Virginia, USA
Post  Posted 16 Mar 2023 7:02 am     legs slipping
Reply with quote

Everyone is talking about clutch....what and where is a clutch.
View user's profile Send private message Send e-mail
Randy Cook

 

From:
Mechanicsville, Virginia, USA
Post  Posted 16 Mar 2023 7:13 am     Pedal board slipping
Reply with quote

I play a D-10 Mullen PRP...pretty old. When I engage a pedal, the pedal board starts slipping down the leg. This causes my tuning to go wonkie!

I thought I might try to decrease the distance between the top of the rubber foot and the botton of the tightening grip. In other words, push the inner leg further into the outer leg. The board would not be able move...the rubber foot would stop any slipping. Thoughts?
View user's profile Send private message Send e-mail
Willie Sims

 

From:
PADUCAH, KY, USA
Post  Posted 20 Mar 2023 11:35 am    
Reply with quote

I HAVE USED METAL COLLARS WITH LOCK SCREWS ON THE BACK LEGS.
View user's profile Send private message
Randy Cook

 

From:
Mechanicsville, Virginia, USA
Post  Posted 21 Mar 2023 10:04 am     Slipping pedal board
Reply with quote

I recently put a heat shrink sleeve on the inside leg, below the clutch....everything is working for now!
View user's profile Send private message Send e-mail
Eugene Cole


From:
near Washington Grove, MD, USA
Post  Posted 22 Mar 2023 2:50 pm     Re: legs slipping
Reply with quote

Randy Cook wrote:
Everyone is talking about clutch....what and where is a clutch.


Inside the compression collar which is threaded on to the leg is a compression clutch to hold the legs in place.


Perhaps some will post some photos to explain what we are discussing.
_________________
Regards
-- Eugene <sup>at</sup> FJ45.com

PixEnBar.com
Cole-Luthierie.com
FJ45.com

Sierra U14 8+5 my copedent, 1972 MSA D10 8+4, and nothing in the Bank. 8^)
View user's profile Send private message Send e-mail Visit poster's website

All times are GMT - 8 Hours
Jump to:  
Please review our Forum Rules and Policies
Our Online Catalog
Strings, CDs, instruction, and steel guitar accessories
www.SteelGuitarShopper.com

The Steel Guitar Forum
148 S. Cloverdale Blvd.
Cloverdale, CA 95425 USA

Click Here to Send a Donation

Email SteelGuitarForum@gmail.com for technical support.


BIAB Styles
Ray Price Shuffles for Band-in-a-Box
by Jim Baron