Author |
Topic: L710 split coil- cool enough to install it?? |
Dave Stroud
From: Texas
|
Posted 11 Aug 2018 3:01 pm
|
|
I'm putting a pair of L710s in my Franklin... I'm thinking about using the third lead on each to install split coil switches. Is it a cool enough sound to fuss with it? Looking for the opinions of those who have done this before. Thanks! |
|
|
|
James Collett
From: San Dimas, CA
|
Posted 14 Aug 2018 11:41 am
|
|
I find the sound kind of thin and trebly for regular playing, but it's nice when you're trying to pull off a 1950s-60s Mooney-esque tone. _________________ James Collett |
|
|
|
ajm
From: Los Angeles
|
Posted 15 Aug 2018 6:24 am
|
|
Disclaimer: I have not done it.
But a couple of things to consider.
You could install the pickups, and instead of hard wiring the leads, you could use wire nuts to make the connections. That way you could easily try out the different sounds for a while to see if it's worth it.
And, not trying to be the vintage police or anything, but if you drill holes and mount switches, you may impact any vintage value or collectability of the guitar. With most other guitars it's not really a huge issue, but a Franklin is not most other guitars.
However, if the guitar already has switches, then it's not an issue.
Does the guitar have any pots on it? If so, you could replace a standard pot with a push-pull or (my preference) a push-push and not need to do any drilling. |
|
|
|
Richard Sinkler
From: aka: Rusty Strings -- Missoula, Montana
|
Posted 15 Aug 2018 6:35 am
|
|
As far as mounting the switch, you can take a piece of aluminum angle, mount the switch to it, and secure the switch to the bottom of the guitar. I'm doing that with an XR-16 on my Mullen. _________________ Carter D10 8p/8k, Dekley S10 3p/4k C6 setup,Regal RD40 Dobro, Recording King Professional Dobro, NV400, NV112,Ibanez Gio guitar, Epiphone SG Special (open D slide guitar) . Playing for 54 years and still counting. |
|
|
|
Rich Peterson
From: Moorhead, MN
|
Posted 15 Aug 2018 3:12 pm
|
|
In addition to shorting out one coil by connecting the third wire to ground or hot, put a capacitor (0.02) in line to the other conductor. This will produce the clear harmonics of a single coil, but with the power and most of the humcancellation of the humbucker. A tip from Bill Lawrence.
Gibson recently offered this as "Frequency Compensated Coil Tap." |
|
|
|
Dave Stroud
From: Texas
|
Posted 15 Aug 2018 6:30 pm
|
|
Thanks for the responses. I have no intentions of drilling any holes.... if switches are added, it will be minimally intrusive. No screw holes on the underside either. I guess I'll wire it up and see how it goes! |
|
|
|
Ron Pruter
From: Arizona, USA
|
Posted 15 Aug 2018 7:25 pm
|
|
Dave, single coil sounds cool but,
1) you'll have hum.
2) you'll have less output. RP _________________ Emmons SKH Le Grande, '73 Fender P/J bass, Tick tack bass, Regal high strung, USA Nashville 112. |
|
|
|
Dave Stroud
From: Texas
|
Posted 15 Aug 2018 9:15 pm
|
|
I know a hum will be present, but not any more so than other single-coil pickups, right? Like a true tone? |
|
|
|
Richard Sinkler
From: aka: Rusty Strings -- Missoula, Montana
|
Posted 16 Aug 2018 7:48 am
|
|
Rich Peterson wrote: |
In addition to shorting out one coil by connecting the third wire to ground or hot, put a capacitor (0.02) in line to the other conductor. This will produce the clear harmonics of a single coil, but with the power and most of the humcancellation of the humbucker. A tip from Bill Lawrence.
Gibson recently offered this as "Frequency Compensated Coil Tap." |
Rich,
Can you give more details. I don't completely understand the line I bolded in your response. The only wiring diagram I could find had the red wire (and a green twisted together with the red that my pickup doesn't have) going to one side of the SPST switch, with the other lug on the switch wired to ground (to the ground lug on the jack?). _________________ Carter D10 8p/8k, Dekley S10 3p/4k C6 setup,Regal RD40 Dobro, Recording King Professional Dobro, NV400, NV112,Ibanez Gio guitar, Epiphone SG Special (open D slide guitar) . Playing for 54 years and still counting. |
|
|
|
Georg Sørtun
From: Mandal, Agder, Norway
|
Posted 16 Aug 2018 10:13 am
|
|
There are a few ways to turn a humbucker PU with tap into a single coil PU – or "something" that sounds like one. Not sure if I understood Rich's description correctly either, but here follows a way to include two different variants via one switch…
Using a SPCO (single-pole-center-open) switch, one gets…
- Single Coil by shorting one coil of a humbucker to GND.
- Regular Humbucker.
- Single Coil (sort of) by shorting only the higher frequency range of one coil to GND, via a capacitor. Still acts as a Humbucker in the lower frequency range. |
|
|
|