| Author |
Topic: Steel king power supply |
Eugenio Poppi
From:
Italy
|
Posted 13 Feb 2018 10:47 am |
|
Hi, I recently imported from USA an used steel king amp serial number M1436245. Does anybody knows if is possible to change connections inside the panel in order to switch to 220v or need to change the power unit inside? Thank you eugenio
_________________
MSA legend XL D10 / JCH D-10 / MSA millenium D10 / MSA Millenium SD-10 / Emmons D10 / NV112 / NV400 / lexicon MPX1 / telonics VP/ Beard Resonator 6stg with fishmann aura preamp |
|
|
 |
Lee Baucum
From:
McAllen, Texas (Extreme South) The Final Frontier
|
Posted 13 Feb 2018 11:00 am
|
|
Good question for Sam Marshall, who is or was an engineer with Fender and was instrumental in the development of the Steel King.
He is a member of this Forum.
_________________
Lee, from South Texas - Down On The Rio Grande
There are only two options as I see it.
Either I'm right, or there is a sinister conspiracy to conceal the fact that I'm right.
Williams Keyless S-10, BMI S-10, Evans FET-500LV, Fender Steel King, 2 Roland Cube 80XL's,
Sarno FreeLoader, Goodrich Passive Volume Pedals, Vintage ACE Pack-A-Seat |
|
|
|
Eugenio Poppi
From:
Italy
|
Posted 13 Feb 2018 11:17 am
|
|
Thank you Lee!! Try to find out his mail
_________________
MSA legend XL D10 / JCH D-10 / MSA millenium D10 / MSA Millenium SD-10 / Emmons D10 / NV112 / NV400 / lexicon MPX1 / telonics VP/ Beard Resonator 6stg with fishmann aura preamp |
|
|
|
Bill A. Moore
From:
Silver City, New Mexico, USA
|
|
|
|
Eugenio Poppi
From:
Italy
|
Posted 13 Feb 2018 12:58 pm
|
|
Great! Thank you bill!!
_________________
MSA legend XL D10 / JCH D-10 / MSA millenium D10 / MSA Millenium SD-10 / Emmons D10 / NV112 / NV400 / lexicon MPX1 / telonics VP/ Beard Resonator 6stg with fishmann aura preamp |
|
|
|
Mike Wheeler
From:
Delaware, Ohio, USA
|
Posted 14 Feb 2018 9:06 am
|
|
Bill, may I ask where you got those part numbers? The schematic shows different numbers for the Xformers.
_________________
Best regards,
Mike |
|
|
|
Bill A. Moore
From:
Silver City, New Mexico, USA
|
Posted 14 Feb 2018 9:30 am
|
|
Mike, they're under the transformer pin outs on the power supply page, (page 3).
(I fixed the 5 to 4 on the 120V number above.) |
|
|
|
Sam Marshall
From:
Chandler, AZ USA
|
Posted 14 Feb 2018 8:29 pm
|
|
A transformer change is necessary unless you can find a good 230V to 120V step down transformer. I recalled using such transformers when touring Europe in the USAF band with US wired equipment.
These should be commonly found around US military bases.
Sam in AZ |
|
|
|
Eugenio Poppi
From:
Italy
|
Posted 14 Feb 2018 11:23 pm
|
|
Thank you Very much Sam!
_________________
MSA legend XL D10 / JCH D-10 / MSA millenium D10 / MSA Millenium SD-10 / Emmons D10 / NV112 / NV400 / lexicon MPX1 / telonics VP/ Beard Resonator 6stg with fishmann aura preamp |
|
|
|
