| Visit Our Catalog at SteelGuitarShopper.com |

Post new topic String not returning to tune
Reply to topic
Author Topic:  String not returning to tune
Ben Morine


From:
Queensland, Australia
Post  Posted 13 Nov 2017 1:12 pm    
Reply with quote

Hi guys,

Hope you are all well.

when I hit the b pedal on my Carter the 6th string is going out of tune.

Any ideas on what could be happening?

Any advice would be appreciated.

Thanks

Ben
View user's profile Send private message Send e-mail
Jason Lynch


From:
Essex, United Kingdom
Post  Posted 13 Nov 2017 1:22 pm    
Reply with quote

If it's not returning to pitch after being raised, it's generally one at two things. Either the return Spring need adjusting, or something is preventing the finger returning. Gunk, debris, something broken off. Try getting underneath and push the finger back on not place with a screwdriver. If it goes, it's probably the spring. Needs tightening. If not, it's something else.
View user's profile Send private message Send e-mail
Ken Pippus


From:
Langford, BC, Canada
Post  Posted 13 Nov 2017 2:42 pm    
Reply with quote

Overtuned until proven otherwise. Back off the raise tuners completely and start over.
View user's profile Send private message Send e-mail
Paul Sutherland

 

From:
Placerville, California
Post  Posted 13 Nov 2017 5:58 pm    
Reply with quote

I don't think you have adequately explained what's happening. The B pedal generally raises the sixth string a half tone. The return springs have nothing to do with a pedal or lever that only raises strings.

Did you mean to say that when you hit the A pedal the sixth string goes flat? If so, that would be cabinet drop you are observing on the sixth string.

Did you mean to say that when you hit the B pedal it doesn't raise to the proper pitch? That's a tuning, or overtuning issue. Or did you mean that when you release the B pedal it doesn't return to the proper pitch? That's often a sticky roller nut issue, or something else in the linkage that needs lubrication, or it's an overtuning problem.

I'm not trying to be difficult, but I think you need to clarify.
_________________
It don't mean a thing if it ain't got that swing.
View user's profile Send private message Send e-mail
Ron Pruter

 

From:
Arizona, USA
Post  Posted 13 Nov 2017 8:11 pm    
Reply with quote

I vote overtuned. Curious, did you change string gauge? RP
_________________
Emmons SKH Le Grande, '73 Fender P/J bass, Tick tack bass, Regal high strung, USA Nashville 112.
View user's profile Send private message Send e-mail
Bobby D. Jones

 

From:
West Virginia, USA
Post  Posted 13 Nov 2017 10:05 pm    
Reply with quote

Hi Ben. It could be one of several things. Since you did not give your guitar or set up.

It could be a return spring on the changer finger or pedal return spring,

Next check the nut roller if the guitar is so equipped. The 5th and 6th have a lot of string from the nut roller to the tuner. Loosen the string enough so you can clear the roller and check for free rolling of the 6th string roller. I had that problem with my GFI on some strings, I had to clean about 3 slots of powder coat run when it was baked. with a needle file.

Last Check to make you have a little free play in the nylon nut pull rod assembly. If no free play you may have to move the pull on the bell crank to give the rod a longer pull and a little free play when the raise is tuned and the pedal returns. This could be if you changed string diameter

Good Luck finding the problem, And Happy Steelin.
View user's profile Send private message Send e-mail

All times are GMT - 8 Hours
Jump to:  
Please review our Forum Rules and Policies
Our Online Catalog
Strings, CDs, instruction, and steel guitar accessories
www.SteelGuitarShopper.com

The Steel Guitar Forum
148 S. Cloverdale Blvd.
Cloverdale, CA 95425 USA

Click Here to Send a Donation

Email SteelGuitarForum@gmail.com for technical support.


BIAB Styles
Ray Price Shuffles for Band-in-a-Box
by Jim Baron