| Author |
Topic: Where do you place your effects pedals, if you use them? |
Chris Tweed
From:
Cardiff, Wales, UK
|
Posted 14 Aug 2017 10:45 am |
|
This is probably a stupid question because it hasn't come up in my search of the forum. Where do you put effects pedals in relation to your steel?
I haven't had to think about getting easy access to effects pedals before, mainly because I don't use many and those I do have are usually engaged between songs rather than during them. However, I am starting to use PSG in different types of music and would like to be able to change effects mid-song.
At the moment I have a small pedalboard (three effects and an A/B switch). It sits on the floor to my right, but I can't reach it easily whilst playing. Do most people lift the pedals off the floor and activate them by hand? |
|
|
 |
David Gertschen
From:
Phoenix, Arizona
|
Posted 14 Aug 2017 11:30 am
|
|
Hi Chris, I use a pedaltrain jr. board for my pedals. I too find it uncomfortable reaching down to the floor to make changes. Currently, I just have it propped up on an old milk crate so it is level with my seat.
I have seen some of the steel seat makers that offer side-car like attachments for holding pedals right on the seat. That might be a better/easier way to do it. Perhaps someone will chime in with pics of their setups... |
|
|
|
Lane Gray
From:
Topeka, KS
|
Posted 14 Aug 2017 1:04 pm
|
|
I put those that don't attach to the guitar on the open lid of the sidekick of my seat. And I prefer to keep them out of the chain when not in use.
Each box gets its own input cable, and when we're getting ready to do a song that uses that box (there are often three right there), I'll pull the cable from guitar to volume pedal, plug it into the output of the box, and plug the input cable into the guitar.
_________________
2 pedal steels, a lapStrat, and an 8-string Dobro (and 3 ukes)
More amps than guitars, and not many effects |
|
|
|
Darvin Willhoite
From:
Roxton, Tx. USA
|
Posted 14 Aug 2017 5:51 pm
|
|
On the floor, next to my volume pedal.
_________________
Darvin Willhoite
MSA Millennium, Legend, and Studio Pro, Reese's restored Universal Direction guitar, a restored MSA Classic SS, several amps, new and old, and a Kemper Powerhead that I am really liking. Also a Zum D10, a Mullen RP, and a restored Rose S10, named the "Blue Bird". Also, I have acquired and restored the plexiglass D10 MSA Classic that was built as a demo in the early '70s. I also have a '74 lacquer P/P, with wood necks, and a showroom condition Sho-Bud Super Pro. |
|
|
|
Greg Lambert
From:
Illinois, USA
|
Posted 14 Aug 2017 6:19 pm
|
|
| I use the pre-eq patch for my delay and the post eq patch for my digital reverb. Superb sound. NV112 |
|
|
|
Allan Haley
From:
British Columbia, Canada
|
Posted 14 Aug 2017 8:19 pm
|
|
A little removable shelf I built from extruded aluminum. Lots of room for pedals and strong velcro to keep them in place.
 |
|
|
|
Gordon Hartin
From:
Durham, NC
|
Posted 16 Aug 2017 6:36 am
|
|
I just place my steel case on the right hand side, and put my pedal board on top of the case. I have a Pedal Train JR board.
I also have my steel hit a couple pedal before the volume pedal.
 |
|
|
|
Darvin Willhoite
From:
Roxton, Tx. USA
|
Posted 16 Aug 2017 7:04 am
|
|
Here's my latest setup, I use a Zoom G3 and love it. It is a lot cleaner than all of those old individual pedals, and a lot less potential for cable failures. It's easy to take my foot off the volume pedal and switch the effects without having to take my hands off the strings.
_________________
Darvin Willhoite
MSA Millennium, Legend, and Studio Pro, Reese's restored Universal Direction guitar, a restored MSA Classic SS, several amps, new and old, and a Kemper Powerhead that I am really liking. Also a Zum D10, a Mullen RP, and a restored Rose S10, named the "Blue Bird". Also, I have acquired and restored the plexiglass D10 MSA Classic that was built as a demo in the early '70s. I also have a '74 lacquer P/P, with wood necks, and a showroom condition Sho-Bud Super Pro. |
|
|
|
Stu Schulman
From:
Ulster Park New Yawk (deceased)
|
Posted 16 Aug 2017 7:17 am
|
|
Chris,Good question I set my steel guitar case to my right and I have my tuner distortion and what ever else I am using at the time on the case I also turn the effects on and off with my hands,I've never been comfortable have my effects pedals on the floor?
_________________
Steeltronics Z-pickup,Desert Rose S-10 4+5,Desert Rose Keyless S-10 3+5... Mullen G2 S-10 3+5,Telonics 206 pickups,Telonics volume pedal.,Blanton SD -10,Emmons GS_10...Zirctone bar,Bill Groner Bar...any amp that isn't broken.Steel Seat.Com seats...Licking paint chips off of Chinese Toys since 1952. |
|
|
|
b0b
From:
Cloverdale, CA, USA
|
Posted 16 Aug 2017 10:02 am SKB pedal board
|
|
I just bought the SKB 9v powered pedal board. $100 from Sweetwater. I'm using an old speaker stand to raise it. A plastic milk crate would work, too.
Three of my devices don't use 9v, so I have 4 separate power supplies. I'm thinking that with a milk crate, I could have a power strip in the crate with everything plugged in, and get rid of all that mess.
_________________
-𝕓𝕆𝕓- (admin) - Robert P. Lee - Recordings - Breathe - D6th - Video |
|
|
|
Kevin Mincke
From:
Farmington, MN (Twin Cities-South Metro) USA
|
Posted 16 Aug 2017 6:21 pm
|
|
I've always had my pedalboard set up on my right on a folding type "camp" seat or set them on my SKB case for my electronics/mics etc. it's just the right height. Most my pedals were bought in the late 70's/80's and I have also used my right hand, so the pedals aren't all beat up & kicked around. Here's a photo from a few years ago...my board has changed some however.
 |
|
|
|
Jack Stanton
From:
Somewhere in the swamps of Jersey
|
|
|
|
Karen Sarkisian
From:
Boston, MA, USA
|
Posted 17 Aug 2017 12:34 pm
|
|
| Gordon Hartin wrote: |
I just place my steel case on the right hand side, and put my pedal board on top of the case. I have a Pedal Train JR board.
I also have my steel hit a couple pedal before the volume pedal.
|
whats the red pedal (bottom left) ? klone ??
_________________
Emmons, Franklin, Mullen |
|
|
|
Ron Hogan
From:
Nashville, TN, usa
|
Posted 21 Aug 2017 7:32 pm
|
|
When I'm not using my rack effects unit and just want to travel light with one reverb/delay/chorus unit, I made a little platform from a mic clip.
I had found when the stompbox was on the floor, I couldn't see it well enough to adjust it. Now it is close to me.
 |
|
|
|
David Gertschen
From:
Phoenix, Arizona
|
Posted 22 Aug 2017 11:23 am
|
|
| Pretty nifty, Ron. I like it! |
|
|
|
Bobby Nelson
From:
North Carolina, USA
|
Posted 22 Aug 2017 3:26 pm
|
|
| wow bOb, I used to have a Tube Rotoshere. I loved it. A great way to avoid hauling around a Leslie 122. |
|
|
|
b0b
From:
Cloverdale, CA, USA
|
Posted 22 Aug 2017 8:47 pm
|
|
| Bobby Nelson wrote: |
| wow bOb, I used to have a Tube Rotosphere. I loved it. A great way to avoid hauling around a Leslie 122. |
It emulates the cabinet and tube overdrive as well as the two rotating elements. Plus it sounds good in mono. I like it a lot!
_________________
-𝕓𝕆𝕓- (admin) - Robert P. Lee - Recordings - Breathe - D6th - Video |
|
|
|
Julian Goldwhite
From:
Alhambra, CA, USA
|
Posted 23 Aug 2017 7:12 am
|
|
I built this switcher box to address the effects issue as a pedal steel playing utility musician. The Hammond enclosure's top 3 switches toggle between different instruments (psg, guitar/lap steel and dobro/banjo depending on gig, etc. The bottom 3 switches are 3 true bypass loops; I find one delay, one distortion and one modulation (plus ebow and some extended musical techniques) give me enough textural variety to make for good tonal building blocks in my live music production. The box clips to my right rear leg with two heavy duty broom clips.
Best,
Julian
_________________
http://www.bellgardensmusic.com/
http://www.facebook.com/BellGardens |
|
|
|
Glenn Demichele
From:
(20mi N of) Chicago Illinois, USA
|
Posted 24 Sep 2017 6:10 pm I made a little effects table today
|
|
I use a Boss GT-001, and because of its weird size, I've had trouble finding a convenient place to put it. I made this nice little table that slides in at the top of the legs, then grabs as it drops down.
_________________
Franklin D10 8&5, Excel D10 8&5. Both amazing guitars! Homemade buffer/overdrive with adjustable 700Hz "Fender" scoop., Moyo pedal, GT-001 effects, 2x TDA7294 80W class AB amps, or 2x BAM200 for stereo. TT12 and BW1501 each in its own closed back wedge. Also NV400 etc. etc... |
|
|
|
b0b
From:
Cloverdale, CA, USA
|
Posted 24 Sep 2017 8:28 pm
|
|
I just replaced my Rotosphere with a Strymon Lex. Wow - what a great sound! I'm in heaven. Here's what my pedalboard looks like now:
_________________
-𝕓𝕆𝕓- (admin) - Robert P. Lee - Recordings - Breathe - D6th - Video |
|
|
|
Bill Terry
From:
Bastrop, TX
|
Posted 25 Sep 2017 10:29 am
|
|
I've regressed considerably over the last year... this is it, one DD-3 on the amp, and the Quilter has a DC jack on the back, so not even a wall wart.
 |
|
|
|
Drew Pierce
From:
Arkansas, USA
|
Posted 25 Sep 2017 2:07 pm
|
|
| Bill Terry wrote: |
I've regressed considerably over the last year... this is it, one DD-3 on the amp, and the Quilter has a DC jack on the back, so not even a wall wart.
|
Bill, I like your thinking. All I use in the way of effects other than the amp's onboard reverb is a bit of delay on some songs. And like yours, mine sits on the amp where I can easily punch it in and out or tweak it as needed.
_________________
Drew Pierce
Emmons D10 Fatback, S10 bolt-on, Zum D10, Evans RE500, Hilton volume and delay pedals. |
|
|
|
Bill Terry
From:
Bastrop, TX
|
Posted 27 Sep 2017 8:24 am
|
|
| Quote: |
| All I use in the way of effects other than the amp's onboard reverb is a bit of delay on some songs. |
Same here, and I'm really fond of the Quilter verb. The 3 control setup with Dwell and Tone added make it really flexible.
After a lot of effects processing experiments, I've decided that I'd be better off to spend the time and money on lessons..  |
|
|
|
Cody Russell
From:
Arkansas, now in Denver
|
Posted 11 Oct 2017 2:42 pm
|
|
_________________
carter pro, 66 twin revrerb, steel king, tut taylor dobro, gibson rb 250 |
|
|
|
Tim Harr
From:
Dunlap, Illinois
|
Posted 13 Oct 2017 1:43 pm
|
|
I use a small pedaltrain board. I just put the board on top of the case and my tuner on the steel leg.
_________________
Tim Harr
Mullen G2 D-10, Fender Telecaster B Bender, Martin HD-28, Sire H7
Retired, US Army Band (Steel/Dobro/Guitar)
Kemper Profiler / LW 89 |
|
|
|
