Sho-Bud Voulume Pedal String

Tony Oresteen · From: Georgia, USA

I bought a used Sho-Bud volume pedal with a known bad pot and ordered a Dunlop pot for it from Tom Bradshaw. Started work on it today and the string is a bit frayed so I want to replace it as well.

I can't find a source for the original string. Some posts say use fly fishing leader line, one said use a waxed shoelace for dress shoes. Google doesn't come up with anything.

Any one know what type string Sho-Bud used and where to get it?

Would an Ernie Ball String & Spring kit work with the Sho-Bud pedal?

Thanks!
_________________
Tony
Newnan, GA

Too many guitars, not enough time to play
'72 Sho-Bud 6139, '71 Marlen 210
'78 Fender Stringmaster Quad black
PedalMaster D8

Robert Parent · From: Gillette, WY

Another vote for fly fishing line.... It worked the best of anything I used over the years, easy to find, and cheap to purchase.

Most any heavy string will work, most just will not last very long. There really is no magic other than getting it routed in the pedal.

Robert

Edward Rhea · From: Medford Oklahoma, USA

Here you go Tony, just in case you need it!?
http://bb.steelguitarforum.com/viewtopic.php?p=1775771&highlight=#1775771
_________________
â€œTONESNOBâ€

Dennis Detweiler · From: Solon, Iowa, US

I replaced mine many years ago with heavy nylon cord, the kind you use for bank fishing poles or throw lines. I think it's about 100lb test? Anyway, it's still on the pedal and looking good after all these years.
I modified the center post and cut it shorter and added a pulley wheel on it. Then ran the cord over the pulley wheel and added a tension spring to the end and anchored it to the center of the pedal frame with a screw. That way, as the string stretches it will still stay tight and you get a smoother rotation of the pot.
_________________
1976 Birdseye U-12 MSA with Telonics 427 pickup, 1975 Birdseye U-12 MSA with Telonics X-12 pickup, Revelation preamp, Carbon Copy Delay and Hall Of Fame Reverb, Crown XLS 1002, 2- 15" Eminence Wheelhouse speakers, ShoBud Pedal, Effects Pedals. 1949 Epiphone D-8.

Lane Gray · From: Topeka, KS

I'd always thought it looked like chalk line string. And I was once told to use that.
_________________
2 pedal steels, a lapStrat, and an 8-string Dobro (and 3 ukes)
More amps than guitars, and not many effects

robert kramer · From: Nashville TN

http://www.goodrichsoundcompany.com/Accessories_c_18.html

Tony Oresteen · From: Georgia, USA

Thanks all! I removed the old string and measured it. It's about 12" long and about 0.048" thick. Since it old and worn I assume it's stretched out a bit.

This afternoon I realized that I have a spool of surplus nylon sash cord that we use in HAM radio for antenna guy lines that is very strong, doesn't stretch, and is very cheap (yes, I'm a HAM - W1AJO). I measured it and it's 0.050" thick. Perfect!

I cut 13" off and laid it out next to the old string.

Next up is to restring the pedal using my sash cord.
_________________
Tony
Newnan, GA

Too many guitars, not enough time to play
'72 Sho-Bud 6139, '71 Marlen 210
'78 Fender Stringmaster Quad black
PedalMaster D8

robert kramer · From: Nashville TN

Sometimes it's good to put violin rosin or a little rubber cement where the string runs across the pulley. Also - chewing gum works, too.

Tony Oresteen · From: Georgia, USA

robert kramer · From: Nashville TN

I know - I know - and I bought a couple of them. At least they look good - if only the audience could see them.

"It's only money... it'll go away."

Mark Draycott R.I.P. · From: Portland, OR

I used the cord from an old set of blinds. You could buy a new cheap set of blinds for a few bucks, if needed
_________________
1976 Sho-Bud Pro II, 1976 Sho-Bud LDG, BF Fender Deluxe, Evans FET 500 LV, BF Princeton Reverb, '68 Vibrolux Reverb

Jim Palenscar · From: Oceanside, Calif, USA

You can use almost anything if you trust it~or you could drive to the hardware store and get mason's twine and do the next 1,000 pedals that you need to restring and while you're there you can get the right screw and rubber based washer~~ or you can spend $12 and stay home and practice. Smile

Tony Oresteen · From: Georgia, USA

All is fixed! The pictures on this site were very helpful. It took me a while to figure out how the danged string goes.

Tom Bradshaw's 470K pot works like a charm.

The 0.050" sash cord I used is surplus from the North Carolina mills that make blinds and privacy curtains. I have a big spool of it so if someone needs a piece to fix a Sho-Bud pedal I'll give you a piece if you provide a SASE.

Question: why don't PSG volume pedals use gear drives like my Dunlop Wha Wha & Vox volume pedals do?
_________________
Tony
Newnan, GA

Too many guitars, not enough time to play
'72 Sho-Bud 6139, '71 Marlen 210
'78 Fender Stringmaster Quad black
PedalMaster D8

Jim Palenscar · From: Oceanside, Calif, USA

Both methods work well to rotate the shaft of a pot. It has been my experience that gear drives have a higher rate of failure than a string and are harder to find as one needs the mate to what you had depending on if it's the track or gear that has failed.

Steve Smith · From: Bramalea, Ontario, Canada

fly line is the ticket it is plastic coated
nylon won't slip and won't break I've been using
it for 40yrs never ever broke one about 15dollars for 100yds

Carl Mesrobian · From: Salem, Massachusetts, USA

Seriously , does it matter whether it's salt water or fresh water? I just looked online and there are too many choices Smile

http://www.orvis.com/fly-lines

EDIT - I just saw Jim's post about mason's twine - that what I use now - no need to go fishing.

John LeMaster · From: North Florida

I had read that a waxed shoe lace would suffice as volume pedal string. Stopped at the local Dollar Tree hoping to find waxed shoe laces. They didn't have the waxed variety, but on the same aisle, they had drawstring tote bags. I didn't need a tote bag, but these bags come with nice nylon string. About 10 feet of it! It works very well (only $1 for 10 feet of string, and you get a tote bag)

_________________
Magnum D10, Emmons D10 push-pull

Forum Index > Electronics		Next oldest topic :: Next newest topic