| Visit Our Catalog at SteelGuitarShopper.com |

Post new topic Pedal Rod labels
Goto page 1, 2  Next
Reply to topic
Author Topic:  Pedal Rod labels
Ollin Landers


From:
Willow Springs, NC
Post  Posted 1 Apr 2016 12:50 pm    
Reply with quote

OK. This is about the silliest question I can think of. I'm sure there is a better way to do this.

Every guitar I've owned I've had trouble with keeping any kind of label on the pedal rods. My Zum has the clip type and my Carter had the stick on labels.

I lost all the stick ons on the Carter and replaced them with clips. But they keep falling off or getting lost. Same with the Zum.

I know some guys in the old days used electrical tape at different places on the rods to denote what position to put them in. If it didn't look so bad I'd probably do it.

Has anyone come up with a better method other than the ID Clips?
Is there any way to get those clips to stay on?
_________________
Zum SD-12 Black, Zum SD-12 Burly Elm Several B-Bender Tele's and a lot of other gear I can't play.

I spent half my money on gambling, alcohol and wild women. The other half I wasted. W.C. Fields
View user's profile Send private message Send e-mail
Dave Diehl

 

From:
Mechanicsville, MD, USA
Post  Posted 1 Apr 2016 12:59 pm    
Reply with quote

Ollin, I had the same problems. I finally got some clip on numbers from Lynn Flanagan landflag@gmail.com and they stayed on. I have them on all my guitars now and never had a problem with any of them falling off.
View user's profile Send private message Send e-mail
John Swain


From:
Winchester, Va
Post  Posted 1 Apr 2016 1:04 pm    
Reply with quote

After the stickers fell off my Carter I wrote numbers on the bottom with a Sharpie. Still there eight years later.
View user's profile Send private message Send e-mail
Erv Niehaus


From:
Litchfield, MN, USA
Post  Posted 1 Apr 2016 1:24 pm    
Reply with quote

Bill Rudolph with Williams Guitars has those clip on numbers for sale. I have had no trouble keeping them on.
View user's profile Send private message Send e-mail
Wesley Medlen

 

From:
LaCygne,Ks
Post  Posted 1 Apr 2016 1:50 pm    
Reply with quote

My BMI's have them stenciled on the coupling
_________________
Justice S10 Jr, Gibson Electra 6string, Boss Katana 100, Steelers Choice ,Gretsch 6 string lap, Hilton VP
View user's profile Send private message Send e-mail
Jerry Overstreet


From:
Louisville Ky
Post  Posted 1 Apr 2016 2:02 pm    
Reply with quote

You can buy a number stamp set from www.harborfreight.com for $11 or $15. Stamp the # on the bottom of the pedal connector like Mullen does. You can put a little fluorescent paint or a color you can see well in dim light, in the recess.
View user's profile Send private message
Greg Cutshaw


From:
Corry, PA, USA
Post  Posted 1 Apr 2016 3:07 pm    
Reply with quote

My MSA legend had all the pedal rods the same exact length with the variable height adjustment affixed to the guitar body. Thus no need to number the pedal rods as they are interchangeable.


View user's profile Send private message Send e-mail Visit poster's website Yahoo Messenger
Ron Funk

 

From:
Ballwin, Missouri
Post  Posted 1 Apr 2016 3:21 pm    
Reply with quote

Ollin -

I've done what I was told some 30 years ago.

For each of my Emmons PP's, I've gone to a craft store (Hobby Lobby, Michael's, etc) and bought a sheet of those small self adhesive numbers, and applied proper number to each corresponding pedal rod connector.

You can then apply small dab of clear fingernail polish over each number as kind of a sealer.
View user's profile Send private message Send e-mail
Lane Gray


From:
Topeka, KS
Post  Posted 1 Apr 2016 4:00 pm    
Reply with quote

A bit of sticky on the inside of the clips helps.
I do like the struck numbers on my Sho-Bud,but they're not easy
_________________
2 pedal steels, a lapStrat, and an 8-string Dobro (and 3 ukes)
More amps than guitars, and not many effects
View user's profile Send private message Send e-mail Yahoo Messenger
Brint Hannay

 

From:
Maryland, USA
Post  Posted 1 Apr 2016 10:19 pm    
Reply with quote

John Swain wrote:
After the stickers fell off my Carter I wrote numbers on the bottom with a Sharpie. Still there eight years later.

Sharpie works for me, too (Sho-Bud Super Pro, in my case). Easy, cheap. When the numbers get faded, I go over them with fresh Sharpie.
View user's profile Send private message Send e-mail
Mike Perlowin


From:
Los Angeles CA
Post  Posted 2 Apr 2016 12:42 am    
Reply with quote

Greg Cutshaw wrote:
My MSA legend had all the pedal rods the same exact length with the variable height adjustment affixed to the guitar body. Thus no need to number the pedal rods as they are interchangeable.



Same with my Millies. All the new MSAs are like this.

Reece once told me he liked to alter the pedal height to adjust to the floor when he played.
_________________
Please visit my web site and Soundcloud page and listen to the music posted there.
http://www.mikeperlowin.com http://soundcloud.com/mike-perlowin
View user's profile Send private message Send e-mail Visit poster's website
Donny Hinson

 

From:
Glen Burnie, Md. U.S.A.
Post  Posted 2 Apr 2016 2:33 am    
Reply with quote

The MSA design is novel, but I do wish they'd kept a hook on the top end. Fidgeting with the straight-line connectors just takes more time, and more than once (while not paying attention to the red mark) I've gotten the straights and right-angles mixed up. Oh Well

As far as rod labels go, just print them on paper with your computer, cut into strips and wrap the around the rods, covering them with Scotch tape. That way, you get to pick the font, font size, orientation and position. Very Happy
View user's profile Send private message Send e-mail
David Nugent

 

From:
Gum Spring, Va.
Post  Posted 2 Apr 2016 3:46 am    
Reply with quote

This method may apply more to single neck guitars. I painted the bottom of the rod clips on my Emmons red, white, and blue left to right, (if you happen to have the fourth Franklin pedal, simply leave it unpainted). Certainly beat attempting to read those stamped numbers in dim light.
View user's profile Send private message
Ollin Landers


From:
Willow Springs, NC
Post  Posted 2 Apr 2016 7:24 am    
Reply with quote

Thank you to everyone. You guys are great.

Not a bad suggestion in the whole thread. The top of my list is a new Millennium with interchangeable pedal rods. Sadly that's out of the question at this time.

I'm going to sift through the list and decide which one will work the best for me.
_________________
Zum SD-12 Black, Zum SD-12 Burly Elm Several B-Bender Tele's and a lot of other gear I can't play.

I spent half my money on gambling, alcohol and wild women. The other half I wasted. W.C. Fields
View user's profile Send private message Send e-mail
Stu Schulman


From:
Ulster Park New Yawk (deceased)
Post  Posted 2 Apr 2016 7:27 am    
Reply with quote

I'm so used to the electrical tape thing that I have adapted that using"Heat Shrink"I just can't see little taped on numbers without reading glasses,I will post some pictures tomorrow...ive always liked the MSA method. Winking
_________________
Steeltronics Z-pickup,Desert Rose S-10 4+5,Desert Rose Keyless S-10 3+5... Mullen G2 S-10 3+5,Telonics 206 pickups,Telonics volume pedal.,Blanton SD -10,Emmons GS_10...Zirctone bar,Bill Groner Bar...any amp that isn't broken.Steel Seat.Com seats...Licking paint chips off of Chinese Toys since 1952.
View user's profile Send private message Send e-mail
Mike Perlowin


From:
Los Angeles CA
Post  Posted 2 Apr 2016 8:36 am    
Reply with quote

Ollin Landers wrote:
The top of my list is a new Millennium ...


Sadly, the Millennium has been discontinued. MSA still makes wood guitars though.
_________________
Please visit my web site and Soundcloud page and listen to the music posted there.
http://www.mikeperlowin.com http://soundcloud.com/mike-perlowin
View user's profile Send private message Send e-mail Visit poster's website
Dave Magram

 

From:
San Jose, California, USA
Post  Posted 2 Apr 2016 9:47 am    
Reply with quote

Here’s a two-part solution that I came up with many years ago when I re-framed the problem as “What is the most efficient and convenient way to assemble my pedal steel, even on a poorly-lit stage or when I’m in a hurry (or both)?” Very Happy

1.Marking the pedal rods: The hex pedal rod-end connectors on my guitar are painted black--a felt-tipped pen wouldn’t work. So I used “White-Out” (which is really white paint) to paint the flat bottom of the connector.
Once the white paint dried, I wrote on it the number of the rod in black ink, and coated it with clear lacquer (or clear fingernail polish) to protect it. That was many years ago, and all of the numbers remain quite readable.

2.Storing the rods in order: Next my wonderful wife bought a 24” x 36” thin black towel and some sturdy cloth with an attractive design on it, and with her sewing machine (a thin towel is easier to sew in a sewing machine) sewed four wide pockets for the legs and ten narrow pockets for the pedal rods in this order: two leg pockets, ten pedal rod pockets, two leg pockets. (I only have eight pedal rods, but having ten pockets makes it easier to quickly store the pedal rods in sequence.)
By taking an extra few seconds when I pack up the guitar to put the pedal rods in the pockets in sequence, there is no fumbling around setting up at the next gig. (And if I ever want to double-check that I’ve attached the correct rod to each pedal, I just read the black-on-white numbers on the bottoms of the pedal rod connectors--easy to see when the steel is upside-down in the case.)
And once the pedal steel is assembled, the towel serves as a protective cover to keep the dust off.

-Dave
View user's profile Send private message Send e-mail
Mike Ester


From:
New Braunfels, Texas, USA
Post  Posted 2 Apr 2016 6:23 pm    
Reply with quote

I used a Dremel tool to grind the numbers on my rods. Still visible since 2005. Smile
_________________
U.S.A.F. 1978-1982
2005 Carter S12U 7x5
1978 Sho-Bud Pro II Custom 8x4

If you can't be a good example, be a horrible warning.
View user's profile Send private message Send e-mail Visit poster's website
memphislim


From:
Austin, Texas
Post  Posted 4 Apr 2016 12:14 pm    
Reply with quote

Mike Ester wrote:
I used a Dremel tool to grind the numbers on my rods. Still visible since 2005. Smile



http://www.amazon.com/Dremel-290-01-Stroke-Engraver-Template/dp/B0000302YN
View user's profile Send private message Send e-mail Visit poster's website
Bob Sykes


From:
North Carolina
Post  Posted 5 Apr 2016 2:05 pm     rod identification
Reply with quote

Like David, I used colors to match up the rods, Also colored the corresponding tuning nut ends to make life easier.

Being an old elec tech, I used the resistor color code.


Potential drawback is assembly under colored light can make red and brown look the same.
_________________
Carters Starter, D10 8+7, SD10, Chandler RH-2, Rogue RLS-1
ISO Sustainus Ad Infinitum
View user's profile Send private message Send e-mail
Mark Fasbender

 

Post  Posted 1 May 2016 11:51 pm    
Reply with quote

i like the tape in different positions. i dont think it looks bad and i can see it quite clearly
View user's profile Send private message Send e-mail
Dave Hopping


From:
Aurora, Colorado
Post  Posted 5 May 2016 8:15 am    
Reply with quote

What Mark said.If a good part of the crowd thinks we're playing a keyboard,they're not likely to notice the pedal rods,or whether they have little pieces of tape around them.

Winking
View user's profile Send private message Send e-mail Visit poster's website
Glenn Demichele


From:
(20mi N of) Chicago Illinois, USA
Post  Posted 5 May 2016 9:31 am    
Reply with quote

I put multiple little strips of tape on each rod to number them in binary
_________________
Franklin D10 8&5, Excel D10 8&5. Both amazing guitars! Homemade buffer/overdrive with adjustable 700Hz "Fender" scoop., Moyo pedal, GT-001 effects, 2x TDA7294 80W class AB amps, or 2x BAM200 for stereo. TT12 and BW1501 each in its own closed back wedge. Also NV400 etc. etc...
View user's profile Send private message Send e-mail
Henry Matthews


From:
Texarkana, Ark USA
Post  Posted 5 May 2016 10:57 am    
Reply with quote

These work great. Can buy them at an Electrical Supply house. Will do oodles of guitars and then some. They are little stick on strips. Just wrap around pedal rod.

_________________
Henry Matthews

D-10 Magnum, 8 &5, dark rose color
D-10 1974 Emmons cut tail, fat back,rosewood, 8&5
Nashville 112 amp, Fishman Loudbox Performer amp, Hilton pedal, Goodrich pedal,BJS bar, Kyser picks, Live steel Strings. No effects, doodads or stomp boxes.
View user's profile Send private message Send e-mail
Scott Duckworth


From:
Etowah, TN Western Foothills of the Smokies
Post  Posted 5 May 2016 12:10 pm    
Reply with quote

Colored paint or sharpie dots on the rod and pedal.
_________________
Amateur Radio Operator NA4IT (Extra)
http://www.qsl.net/na4it

I may, in fact, be nuts. However, I am screwed onto the right bolt... Jesus!
View user's profile Send private message Send e-mail Visit poster's website

All times are GMT - 8 Hours
Jump to:  
Please review our Forum Rules and Policies
Our Online Catalog
Strings, CDs, instruction, and steel guitar accessories
www.SteelGuitarShopper.com

The Steel Guitar Forum
148 S. Cloverdale Blvd.
Cloverdale, CA 95425 USA

Click Here to Send a Donation

Email SteelGuitarForum@gmail.com for technical support.


BIAB Styles
Ray Price Shuffles for Band-in-a-Box
by Jim Baron