| Author |
Topic: Miller Parts |
Al Risbeck
From:
Iowa, USA
|
Posted 24 Jul 2014 7:07 am |
|
Anyone have any Miller pedal steel parts ?
_________________
Mullen Discovery, GK mb200 with Eminence EPS-15C, Fender steel King with Eminence EPS-15C,Nashville 400 amp, with EPS-15C,Evans FET500 with Peavey 1501 BW Goodrich L10K V.P.(2),Goodrich L120, Bose L1 PA with ToneMatch 4 Mic control board |
|
|
 |
Glenn Uhler
From:
Trenton, New Jersey, USA
|
Posted 24 Jul 2014 7:41 am Old parts
|
|
I'm sure Mike Yahl could make them for you at a reasonable price, if you have an original part and he isn't too busy making parts for inventory.
_________________
1974 Marlen S-12 1968 Tele 1969 Martin D-35H |
|
|
|
Al Risbeck
From:
Iowa, USA
|
Posted 24 Jul 2014 7:29 pm parts
|
|
Thanks for your idea Glenn, but I have looked at his website and didn't anything that would work. The parts are unique and a lot of them, this may end up being a nice S-10 non pedal.
Al
_________________
Mullen Discovery, GK mb200 with Eminence EPS-15C, Fender steel King with Eminence EPS-15C,Nashville 400 amp, with EPS-15C,Evans FET500 with Peavey 1501 BW Goodrich L10K V.P.(2),Goodrich L120, Bose L1 PA with ToneMatch 4 Mic control board |
|
|
|
Rick Abbott
From:
Indiana, USA
|
Posted 25 Jul 2014 12:18 pm
|
|
What are you looking for exactly? "Miller Parts" is vague.
_________________
RICK ABBOTT
Sho~Bud D-10 Professional #7962
Remington T-8, Sehy #112
1975 Peavey Pacer |
|
|
|
Richard Sinkler
From:
aka: Rusty Strings -- Missoula, Montana
|
Posted 25 Jul 2014 1:12 pm Re: parts
|
|
| Al Risbeck wrote: |
Thanks for your idea Glenn, but I have looked at his website and didn't anything that would work. The parts are unique and a lot of them, this may end up being a nice S-10 non pedal.
Al |
He does custom work.
http://www.psgparts.com/Custom-Parts_c11.htm
_________________
Carter D10 8p/8k, Dekley S10 3p/4k C6 setup,Regal RD40 Dobro, Recording King Professional Dobro, NV400, NV112,Ibanez Gio guitar, Epiphone SG Special (open D slide guitar) . Playing for 54 years and still counting. |
|
|
|
Al Risbeck
From:
Iowa, USA
|
Posted 25 Jul 2014 2:14 pm Miller Parts
|
|
I'm looking for crossrods, bellcranks, springs and spring retainers, one pedal and two changer fingers, they are quite different. here is a pic. thanks for asking I hope this helps.
_________________
Mullen Discovery, GK mb200 with Eminence EPS-15C, Fender steel King with Eminence EPS-15C,Nashville 400 amp, with EPS-15C,Evans FET500 with Peavey 1501 BW Goodrich L10K V.P.(2),Goodrich L120, Bose L1 PA with ToneMatch 4 Mic control board |
|
|
|
Rick Abbott
From:
Indiana, USA
|
|
|
|
Glenn Uhler
From:
Trenton, New Jersey, USA
|
Posted 27 Jul 2014 8:13 am Miller parts
|
|
For starters, you can probably get the stainless steel rod for the crossshafts at any Ace or True Value hardware store. You can cut it to length with a hacksaw.
The pedal looks a lot like a Marlen pedal. There might be a few of those around. The other parts look peryy much "custom". Guess that's why they called it a "Miller Custom".
_________________
1974 Marlen S-12 1968 Tele 1969 Martin D-35H |
|
|
|
Al Risbeck
From:
Iowa, USA
|
Posted 27 Jul 2014 8:32 am Miller Parts
|
|
Yeah Glenn I had a new Miller Custom D-10 back in the '60s. I could make all the cross shafts I need but without the bell cranks, spring retainers etc. I still don't have anything much. I'll check Scottys out tomorrow. Thanks
Al
_________________
Mullen Discovery, GK mb200 with Eminence EPS-15C, Fender steel King with Eminence EPS-15C,Nashville 400 amp, with EPS-15C,Evans FET500 with Peavey 1501 BW Goodrich L10K V.P.(2),Goodrich L120, Bose L1 PA with ToneMatch 4 Mic control board |
|
|
|
Al Risbeck
From:
Iowa, USA
|
Posted 1 Aug 2014 6:03 am Miller Parts
|
|
Up
_________________
Mullen Discovery, GK mb200 with Eminence EPS-15C, Fender steel King with Eminence EPS-15C,Nashville 400 amp, with EPS-15C,Evans FET500 with Peavey 1501 BW Goodrich L10K V.P.(2),Goodrich L120, Bose L1 PA with ToneMatch 4 Mic control board |
|
|
|
