| Author |
Topic: Bellcrank question -5/16 round shaft... |
Bob Carlucci
From:
Candor, New York, USA
|
Posted 17 Mar 2014 9:12 am |
|
Does anyone make a 5/16 round shaft[sho bud size] bellcrank that is a straight, simple in line design?. Like the Bud Super Pro bellcrank, except made for use with a round shaft. In other words designed to be used with a 90 degree bend and a retaining clip or spring??.. I have seen these for hex shafts, square shafts, and have seen round ones for 3/8 shafts [MSA, Marlen, Dekley], but cannot recall a plain 5 hole bellcrank for round 5/16 shafts.. I can get Sho Bud style 2 hole pullers, but would prefer to go cheaper for what I have in mind.. If anyone is aware of a bellcrank that fits what I am looking for, please let me know... bob
_________________
I'm over the hill and hittin'rocks on the way down!
no gear list for me.. you don't have the time...... |
|
|
 |
Tom Gorr
From:
Three Hills, Alberta
|
Posted 17 Mar 2014 9:18 am
|
|
| Sorry to not answer...but are you trying to add more pulls than your changer is capable of? |
|
|
|
Bob Carlucci
From:
Candor, New York, USA
|
Posted 17 Mar 2014 3:04 pm
|
|
no. not at all.. The steel only has 3 and 3 at present.. I will be adding 2 pedals and 1 knee.. All three pulls are single string pulls.. plenty of room!...
_________________
I'm over the hill and hittin'rocks on the way down!
no gear list for me.. you don't have the time...... |
|
|
|
Bob Carlucci
From:
Candor, New York, USA
|
Posted 18 Mar 2014 1:30 am
|
|
so do these parts exist?.. or no?
_________________
I'm over the hill and hittin'rocks on the way down!
no gear list for me.. you don't have the time...... |
|
|
|
Bill Moore
From:
Manchester, Michigan
|
|
|
|
James Morehead
From:
Prague, Oklahoma, USA - R.I.P.
|
Posted 18 Mar 2014 6:39 am
|
|
Bob, All you have to do is ask, my friend, and you shall receive. These are made of one piece steel, and will accomodate up to 1/8" pullrod rod. The second hole in these particular two, are threaded for a 10-32 ball joint, like for vertical knee levers or LKL knee levers. But I have a stash that are not threaded, too. Ah-ha!! Email me if you want.
 
_________________
"Good judgement comes from experience, and a lot of that comes from bad judgement"~old cowboy proverb.
shobud@windstream.net |
|
|
|
Bob Carlucci
From:
Candor, New York, USA
|
Posted 18 Mar 2014 3:11 pm
|
|
Thats pretty much what I am looking for James, thanks.. I will take inventory of needed parts to convert my "new" Pro I to 5 and 4...
The main reason I wanted this type of bellcrank is because I will have 2 easy lowers on pedals 4 and 5.. One string each.. I was hoping to find something like these as its hopefully cheaper than using 2 hole pullers.. I shouldn't need them for the changes I have in mind.. I will be using nylon hex tuners on some of the lowers at first, and may convert the entire steel,, not sure as yet.. The seller told me it is very tuning stable as it sits.. Says he never has to touch it at a gig... Sent you an email about the levers..... bob
_________________
I'm over the hill and hittin'rocks on the way down!
no gear list for me.. you don't have the time...... |
|
|
|
