| Visit Our Catalog at SteelGuitarShopper.com |

Post new topic 3D printing music instruments
Goto page 1, 2, 3  Next
Reply to topic
Author Topic:  3D printing music instruments
Jan Viljoen


From:
Pretoria, South Africa
Post  Posted 30 Jun 2013 12:43 am    
Reply with quote

This may be the science of the future, 3D printing musical instruments, using all kinds of material.

Who will do the first pedal steel?

http://createdigitalmusic.com/2012/10/six-3d-printed-musical-instruments-and-what-3d-printing-could-do-for-musicians/

This flute was printed in 15 hours.



Copy of a Stradivarius violin.



Playing another 3D printed violin in London.

http://www.youtube.com/watch?v=bJA6J5girlo

Let the games begin!
_________________
Sierra S10, Stage One, Gibson BR4, Framus, Guya 6&8, Hofner lap, Custom mandolins, Keilwerth sax.
Roland Cube 80XL, Peavey112-Valve King and Special, Marshall 100VS.
View user's profile Send private message Send e-mail
Ken Byng


From:
Southampton, England
Post  Posted 30 Jun 2013 2:39 am    
Reply with quote

Jan
While this subject is fascinating and has been discussed on this forum before, the creation and manufacturing of virtually all mechanical stringed musical instruments is very highly dependent in much of the process upon human involvement and intervention.

3D modelling will not encompass the skilled eye of a luthier who hand selects the timber for its resonance and physical beauty / attractiveness. A pedal steel's tone is the result of the sum of its parts and its design. Likewise a Stradivarius can be physically emulated as far as its dimensions are concerned, but impossible to replicate tonally from a 3D printer.

It will be many many years before technology evolves enough to be able to quickly reproduce the most important aspect of any instrument - its tone and timbre.
_________________
Show Pro D10 - amber (8+6), MSA D10 Legend XL Signature - redburst (9+6), Sho-Bud Pro 111 Custom (8+6), Emmons black Push-Pull D10 (8+5), Zum D10 (8x8), Hudson pedal resonator. Telonics TCA-500, Webb 614-E,


Last edited by Ken Byng on 1 Jul 2013 1:21 am; edited 2 times in total
View user's profile Send private message Send e-mail
Jan Viljoen


From:
Pretoria, South Africa
Post  Posted 30 Jun 2013 2:59 am    
Reply with quote

Thanks Ken,

I agree with you in principle, but I think in time adjustments to future software to vary acoustic properties and thicknesses, will come close to the real mccoy.

In a 5 man band with full volume I can't distinguish between a USA, Mexican, Japanese or Korean telecaster either.

I suppose in future printing will also be done with maple fibres (with synthetic flames), gold dust and ivory filings.

Idea
_________________
Sierra S10, Stage One, Gibson BR4, Framus, Guya 6&8, Hofner lap, Custom mandolins, Keilwerth sax.
Roland Cube 80XL, Peavey112-Valve King and Special, Marshall 100VS.
View user's profile Send private message Send e-mail
Norman Boling

 

From:
Paragould Arkansas, Philadelphia TN USA
Post  Posted 30 Jun 2013 3:19 am     Printing
Reply with quote

When Buddy Emmons can be printed I'll be concerned
View user's profile Send private message Send e-mail
Scott Duckworth


From:
Etowah, TN Western Foothills of the Smokies
Post  Posted 30 Jun 2013 3:31 am    
Reply with quote

I would be good if parts for older pedal steels could be reproduced...
_________________
Amateur Radio Operator NA4IT (Extra)
http://www.qsl.net/na4it

I may, in fact, be nuts. However, I am screwed onto the right bolt... Jesus!
View user's profile Send private message Send e-mail Visit poster's website
John Roche


From:
England
Post  Posted 30 Jun 2013 3:39 am    
Reply with quote

Cad drop would be an issue. lol
View user's profile Send private message Send e-mail
Jan Viljoen


From:
Pretoria, South Africa
Post  Posted 30 Jun 2013 4:29 am    
Reply with quote

I found this website regarding printable materials for instruments.

Looks like were are only starting now.


http://3dprintedinstruments.wikidot.com/materials

Idea
_________________
Sierra S10, Stage One, Gibson BR4, Framus, Guya 6&8, Hofner lap, Custom mandolins, Keilwerth sax.
Roland Cube 80XL, Peavey112-Valve King and Special, Marshall 100VS.
View user's profile Send private message Send e-mail
Donny Hinson

 

From:
Glen Burnie, Md. U.S.A.
Post  Posted 30 Jun 2013 7:34 am    
Reply with quote

It's simply not necessary or practical for a pedal steel to be made this way. Acoustic instruments are a different story - they have sound chambers (and they don't have hundreds of little metal parts). Solid bodied electric instruments can be made cheaper and faster without all this technology. So, until it's somehow magically cheaper to do it with a printer, it will not happen. Confused
View user's profile Send private message Send e-mail
Daniel McKee

 

From:
Corinth Mississippi
Post  Posted 30 Jun 2013 10:15 am    
Reply with quote

I still think its amazing that they can make instruments that actually work with a 3D printer.It may not be practical yet but its still pretty awesome.
View user's profile Send private message Send e-mail
Dan Beller-McKenna


From:
Durham, New Hampshire, USA
Post  Posted 30 Jun 2013 11:59 am    
Reply with quote

I think Scott is on to something. Even if it were a three-step process to produce an all-pull finger with a head, and a two part scissor, and even if they all had to be separately riveted, couldn't this have the potential (down the line a little ways) to be an easier way to replicate out of production parts (said the new owner of a pot-metal filled Super Pro, .... hopefully).
View user's profile Send private message Send e-mail Visit poster's website
Donny Hinson

 

From:
Glen Burnie, Md. U.S.A.
Post  Posted 1 Jul 2013 9:09 am    
Reply with quote

Dan Beller-McKenna wrote:
Even if it were a three-step process to produce an all-pull finger with a head, and a two part scissor, and even if they all had to be separately riveted, couldn't this have the potential (down the line a little ways) to be an easier way to replicate out of production parts (said the new owner of a pot-metal filled Super Pro, .... hopefully).


Would it be worth it to you to spend over a thousand dollars on a printer and materials just to make a few hundred dollars worth of parts? I'm not altogether sure that (printed) plastic or metalized parts would even be any improvement over pot metal parts. I do feel, though, that an easier way out of your dilemma would be to swap your guitar for one that wasn't filled with pot metal parts! Wink
View user's profile Send private message Send e-mail
Dan Beller-McKenna


From:
Durham, New Hampshire, USA
Post  Posted 1 Jul 2013 12:11 pm    
Reply with quote

Nah,
I am not worried about the short term health of the metal in the guitar I just acquired; not many miles on it. By the time it get's worn down, here's hoping one of our trusty parts makers will have started cranking out aluminum replacement parts.

I was not thinking about each owner buying his or her own printer; we're decades off from these becoming "personal" devices. Good point about the plastic not being any better than pot metal, but who knows what materials they will be using in these down the road and what their acoustic/mechanical properties will be.
View user's profile Send private message Send e-mail Visit poster's website
Mark van Allen


From:
Watkinsville, Ga. USA
Post  Posted 1 Jul 2013 12:30 pm    
Reply with quote

While looking at a printed plastic flute, bear in mind they're moving toward using "meat ink" to print pork chops... and "stem cell ink" to print new implantable pancreases... not hard to see that technology like this will soon surpass anything we can currently imagine. I foresee some really cool stuff, and some really interesting moral debates.
_________________
Stop by the Steel Store at: www.markvanallen.com
www.musicfarmstudio.com
View user's profile Send private message Send e-mail Visit poster's website
Earnest Bovine


From:
Los Angeles CA USA
Post  Posted 1 Jul 2013 2:09 pm    
Reply with quote

Where do I order the new pancreas?
View user's profile Send private message
Mark van Allen


From:
Watkinsville, Ga. USA
Post  Posted 1 Jul 2013 4:39 pm    
Reply with quote

Probably time to get in line: http://thinkprogress.org/health/2013/05/23/2054281/promising-uses-3d-printing-medicine/
This just amazes me.
_________________
Stop by the Steel Store at: www.markvanallen.com
www.musicfarmstudio.com
View user's profile Send private message Send e-mail Visit poster's website
Clete Ritta


From:
San Antonio, Texas
Post  Posted 1 Jul 2013 7:01 pm    
Reply with quote

While this trombone is not "printed", plastic has certainly come of age for making some acoustic instruments with fairly decent sound quality. I picked up one of these Jiggs P-Bones for around $100, and its perfectly acceptable (and fun) for me as a beginner's starter instrument.



It may lack a little of the harmonic timbre of brass to some degree, but it is also quite a bit lighter in weight compared to its predecessor. More than a few marching band players are now using them in practice.



My only worry is leaving it outside too long in these heatwaves. Laughing
View user's profile Send private message Send e-mail
Jan Viljoen


From:
Pretoria, South Africa
Post  Posted 1 Jul 2013 8:44 pm    
Reply with quote

This thread is getting nice comments and it is getting a life of its own.

Regarding printing body parts, I found this article:

http://www.3ders.org/articles/20130503-australian-researchers-develop-body-parts-using-3d-printing.html

Regarding printing pedal steels I also think that not everybody would have an expensive printer, but I think there will be technical geeks that will print integrated bodies and fret boards.
The materials used will be sorted out eventually.

Printed 6 string electric guitars are already available.

http://www.gizmag.com/awesome-3d-guitar/27387/



By the way, how did the fibre glass psg's sound?

Rods, pickups, legs, and tuners are already available, so that would not be a problem.

Idea
_________________
Sierra S10, Stage One, Gibson BR4, Framus, Guya 6&8, Hofner lap, Custom mandolins, Keilwerth sax.
Roland Cube 80XL, Peavey112-Valve King and Special, Marshall 100VS.
View user's profile Send private message Send e-mail
Glenn Uhler

 

From:
Trenton, New Jersey, USA
Post  Posted 2 Sep 2013 10:03 am     Replacement parts printing!
Reply with quote

Thanks, Jan, for starting this topic. While visiting my brother-in-law yesterday, he showed me some plastic toys he had printed on his personal 3D printer. They were nice colorful 3D toys made from ABS plastic. What I saw convinced me that replacement and custom plastic parts for vintage instruments can easily be made with one of these printers. Think replacement Rickenbacker plates in either white or black ABS plastic for pennies! All you need to do is program the shape into the printing program. Same with pickup covers and pickguards. Check it out at "Reprap" on the web for one example.
_________________
1974 Marlen S-12 1968 Tele 1969 Martin D-35H
View user's profile Send private message Send e-mail
Jan Viljoen


From:
Pretoria, South Africa
Post  Posted 2 Sep 2013 10:21 am     3D Printing
Reply with quote

Thanks Glenn, nice of you to discover this old thread.

Tell us about your 3D plans.

Let the games begin.

Idea
_________________
Sierra S10, Stage One, Gibson BR4, Framus, Guya 6&8, Hofner lap, Custom mandolins, Keilwerth sax.
Roland Cube 80XL, Peavey112-Valve King and Special, Marshall 100VS.
View user's profile Send private message Send e-mail
Glenn Uhler

 

From:
Trenton, New Jersey, USA
Post  Posted 2 Sep 2013 11:00 am     3D programming?
Reply with quote

I'm not a programmer, Jan, but I imagine someone familiar with Solidworks could easily write a program for the shapes necessary to make replacement parts. The beauty here is the ability to make only one part without the need for expensive plastic injection molds and the heavy machinery needed to use them. The greatest expense is the initial programming time, but after that each part is made for pennies, just like with injection molding. They are also working at having the 3D printers duplicate themselves.
_________________
1974 Marlen S-12 1968 Tele 1969 Martin D-35H
View user's profile Send private message Send e-mail
Jan Viljoen


From:
Pretoria, South Africa
Post  Posted 2 Sep 2013 11:31 am    
Reply with quote

Yup, I am sure this science will go from strength to strength, and cheaper eventually.

Go boys, play he game!

Exclamation

Idea
_________________
Sierra S10, Stage One, Gibson BR4, Framus, Guya 6&8, Hofner lap, Custom mandolins, Keilwerth sax.
Roland Cube 80XL, Peavey112-Valve King and Special, Marshall 100VS.
View user's profile Send private message Send e-mail
Kevin Hatton

 

From:
Buffalo, N.Y.
Post  Posted 2 Sep 2013 4:34 pm    
Reply with quote

Except they will NEVER have the sound qualities of of a hand built wood instrument. DOA as far as serious musicians are concerned.
View user's profile Send private message Send e-mail Visit poster's website
Glenn Uhler

 

From:
Trenton, New Jersey, USA
Post  Posted 2 Sep 2013 7:14 pm     Hand-built wood instrument?
Reply with quote

Totally correct, Kevin, but what about a custom pickup cover for that wood-bodied PSG? Or closer to home, custom case corners with the owners initials in them?

Donny posts earlier and I paraphrase: "Why would you buy a $2000 machine to make a few hundred dollars worth of parts?" That's just this week Donny, what about next week. Would you buy a $2000 car and only expect to drive it once?
_________________
1974 Marlen S-12 1968 Tele 1969 Martin D-35H
View user's profile Send private message Send e-mail
Jan Viljoen


From:
Pretoria, South Africa
Post  Posted 2 Sep 2013 8:26 pm     3D Materials
Reply with quote

Never underestimate scientists or innovative people.

Remember the Wright brothers, Bell, Edison, Tesla?
Even Shot Jackson, Buddy Emmons and the early pioneers?

Wood is already in use and I am sure experimenting will bring out the desired tone, colour and looks.

I said before, that wood fibres, ivory filings, gold dust and now even tungsten will be used.

Check out the internet.

http://www.extremetech.com/extreme/156305-company-develops-new-fiber-reinforced-wood-concrete-ink-for-3d-printing

http://www.3ders.org/articles/20130204-wood-filament-laywoo-d3-suppliers-and-price-compare.html

Thanks guys, use your imagination.


Idea
_________________
Sierra S10, Stage One, Gibson BR4, Framus, Guya 6&8, Hofner lap, Custom mandolins, Keilwerth sax.
Roland Cube 80XL, Peavey112-Valve King and Special, Marshall 100VS.
View user's profile Send private message Send e-mail
Ron Randall

 

From:
Dallas, Texas, USA
Post  Posted 3 Sep 2013 5:29 pm    
Reply with quote

Keep an open mind.

If one can imagine a shape, it can be printed.

Back in the day, designing guided missile parts, we would do a "rapid prototype" of complex parts. To visually look at a part sparked lots of imagination. A rapid prototype could be done in a day. To cast it, mold it, or machine it would take weeks or months.

I think it would be useful for making parts in low volume.
Imagine a time when a guitar is ordered, the parts would be made as needed, instead of keeping an inventory.
View user's profile Send private message Send e-mail

All times are GMT - 8 Hours
Jump to:  
Please review our Forum Rules and Policies
Our Online Catalog
Strings, CDs, instruction, and steel guitar accessories
www.SteelGuitarShopper.com

The Steel Guitar Forum
148 S. Cloverdale Blvd.
Cloverdale, CA 95425 USA

Click Here to Send a Donation

Email SteelGuitarForum@gmail.com for technical support.


BIAB Styles
Ray Price Shuffles for Band-in-a-Box
by Jim Baron