Vintage Emmons buying tips

Alex Cattaneo · From: Quebec, Canada

Hey guys, looks like I have an opportunity to get my hands on a vintage S10 Emmons. The seller is an old gentleman so there's no internet communication or emailed pictures or anything like that, I just have to drive to his place and see for myself. Of course, I will most likely take pictures of the guitar and post them here to get your opinion, but I was wondering if you could give me some pointers to help me assess the instrument.

Where is the serial number located? Is there a reference guide somewhere to verify when the guitar was made? What is a wraparound neck? Is that something desirable? How can you tell one from another? Considering that the guitar hasn't been played for a looong time, what are the most likely problems? Are there any common problems that should keep me from buying it?

Any advice is welcomed. Thanks!

Bob Hoffnar · From: Austin, Tx

As far as worth goes you should keep in mind the cost of rebuilding , setting up and or adding levers if needed. S10 with 3 and 4 push pull Emmons are going for around $2000 fully set up and ready to go.

If the steel you are looking at has a wraparound neck it may be worth more. Depends...
_________________
Bob

Alex Cattaneo · From: Quebec, Canada

Thanks Bob. Are wraparound necks the most desirable? Should I pass if it's a bolt-on?

Doug Beaumier · From: Northampton, MA

Wraparounds are early models and are said to have great sustain. Those are very rare. The bolt-on was next, mid-1960's I believe. After that they were all cut-tail. Most of the push/pulls out there are cut-tail.

ANY Emmons p/p is worth getting if the price is reasonable. The early S-10s (1960s, early 70s) usually came with 6 pedals and no knee levers, or possibly 1 or 2 levers... so if that's the case the guitar will need to be setup. Parts are usually custom cut and labor is expensive, so you have to figure that into the price.

The serial number is stamped on the inner side of the endplate at the changer end. It should be 4 digits followed by the letter S. I don't know of any listing of serial numbers for the Emmons S-10s, but I have compiled a list of my own from S-10s I've seen or owned over the years, so when you get the serial number let me know and I can tell you the approximate year. IMO the year is not all that important as far as the value. They are all worth about the same, except possibly the wraparounds.
_________________
My Site / My YouTube Channel
25 Songs C6 Lap Steel / 25 MORE Songs C6 Lap Steel / 16 Songs, C6, A6, B11 / 60 Popular Melodies E9 Pedal Steel

Alex Cattaneo · From: Quebec, Canada

Thanks Doug,

The guitar used to belong to Jerry Robitaille, a local country musician who made regular appearances on TV. From the following two videos, I think the guitar has an aluminum neck:

(skip to 1:25)
http://www.youtube.com/watch?v=edXCZ0y1FQU&feature=relmfu

http://www.youtube.com/watch?v=DNq5MhMHGZQ&feature=relmfu

chris ivey · From: california (deceased)

i've never seen an s10 wraparound. did they make them? all (most) wood neck emmons' were bolt-on and very good. metal neck cuttails were most common and good.

if you have any aptitude for mechanics these are all good. don't fall for the common misinformation that every old steel needs to be rebuilt. it's not necessarily true.

Doug Beaumier · From: Northampton, MA

From what I can see in the video it has several pedals. Looks like 6 pedal rods, but it's hard to tell. The player is definitely pressing pedals that are toward the middle of the instrument, beyond the standard 3 pedals. I didn't notice any knee levers. It looks like a cut tail, with aluminum neck. If you had it converted over to 3 x 4 you could use some of the hardware on the underside from the unused pedals, but you would need to have knee levers made and some other parts. Tommy Cass in Baldwinville Mass. can do that work. Making changes on a push pull is a lot more involved than an all pull. To change that guitar over to 3 x 4 will cost several hundred dollars. It's definitely worth looking at though and making an offer. It may already have a couple of knee levers.. it's hard to tell from the video.

Alex Cattaneo · From: Quebec, Canada

If it has 6 pedals, was it originally made as a C6?

A rebuild would be a tough sell for me, as I'm in Quebec, Canada and capable steel mechanics are nowhere to be found. Al Brisco is a good 6-hour drive from my place. Maybe Dana Flood in Maine or Jerry Fessenden in Vermont? Still, with the price of gas and all, it adds up.

Herb Steiner · From: Briarcliff TX 78669, pop. 2,064

I don't believe it's a wraparound, but looks like a cut-tail to me. I put it on full-screen, though there were wraparounds that got sent back to the factory for modifications and the small decal got replaced by a badge.

Chris
There were S-10 wraparounds made, but not as many as D-10s. I owned one for a good while, sold it to Chris Lucker, and he parted with it some time back. Chris could possibly tell you more, but wraparounds of any format are far from commonplace.

A good number of them were sent to Canada in the very early days of the Emmons Co. and so this thread piqued my interest. One of my wraps came from Canada, in fact.
_________________
My rig: Infinity and Telonics.

Son, we live in a world with walls, and those walls have to be guarded by men with steel guitars. Who's gonna do it? You? You, Lt. Weinberg?

Doug Beaumier · From: Northampton, MA

Alex Cattaneo · From: Quebec, Canada

Well, shipping this thing from Canada + the cost of the rebuild + whatever I will put out to buy the instrument... unless I get a killer deal for the guitar, doesn't seem worth it.

I will visit the seller tomorrow or the next day and post some pics.

Doug Beaumier · From: Northampton, MA

The screws on the end would indicate a cut-tail, but it seems to have additional screws on the side...?

Alex, try to get some close up pics of the undercarriage. Also note the serial number. Maybe you could explain to the seller that the guitar needs to be changed over to a "modern" setup and parts are not longer available, etc. and make him an offer...
_________________
My Site / My YouTube Channel
25 Songs C6 Lap Steel / 25 MORE Songs C6 Lap Steel / 16 Songs, C6, A6, B11 / 60 Popular Melodies E9 Pedal Steel

Alex Cattaneo · From: Quebec, Canada

I don't know if this is for me, but one thing is sure: this guitar should be in the hands of someone who enjoys playing it. I find it rather sad when instruments are just sitting there not being played. If I don't want for me, I'm sure someone else will, and I'll be glad to make it happen!

Nick Reed · From: Russellville, KY USA

Alex,
Here's my little '66 S-10 Bolt-on P/P. It has 3 pedals & 5 knees, tone to die for. . . .great sounding guitar!
Nick

John Lacey · From: Black Diamond, Alberta, Canada

Alex, is Jerry no longer with us? I met him several times in the 70's and he was a sweetheart and and big steel enthusiast.

Alex Cattaneo · From: Quebec, Canada

Hi John,

He passed away several years ago, in 1998 I think. I know a few people started playing steel or became aware of it because he played one on TV.

Paul Norman · From: Washington, North Carolina, USA

Alex, What is the name of that song Jerry and Jo Anne sang on the Ronnie Propet Show.
That was a good song. About Play Easy Loving one more time.

Mac Knowles · From: Almonte,Ontario, Canada

Alex, interesting to discover Jerry's Emmons has turned up somewhere. I knew and played with him for many years since he was a little kid in Lennoxville. Often wondered what happened to his guitars. Jerry was left to his own devices at an early age, worked for Sherbrooke Laundry, and learned to play music pretty much by himself. Great picker though, but came to a sad end when he sort of turned into a hermit. He wanted to be a Canadian distributor for Emmons, hoping he'd get a free guitar that way but didn't. Here's another picture of the two of them a long time ago. Some of you clever folks will recognize the make of steel pictured but I can't think of what it was. Anyway, I'd take the guitar if I was you, wish I had the bucks for it.
Cheers, Mac

John Lacey · From: Black Diamond, Alberta, Canada

Hey Mac. Ran into Jerry and Joanne back in '76. I was playing with Jerry Palmer's band playing a club in Fort Frances Ont. and they blew threw town. Joanne was nice enough to invite us for supper in their travel trailor as the hotel was freezing and the gig sucked. Later in the late 70's I ran into Jerry when I put on some steel shows in St. Albert and he was playing nearby. I was so sorry to hear he passed. Hope Joanne is well.

Alex Cattaneo · From: Quebec, Canada

Mac and John, thanks so much for sharing. It appears all of Jerry's gear as been sitting in this gentleman's house for years. I'll have more details later today.

Herb Steiner · From: Briarcliff TX 78669, pop. 2,064

In the first clip posted, at 6:05, there's another steel player playing an E9 solo on a D-10. Anyone recognize him and the brand of guitar he's playing?
_________________
My rig: Infinity and Telonics.

Son, we live in a world with walls, and those walls have to be guarded by men with steel guitars. Who's gonna do it? You? You, Lt. Weinberg?

Doug Beaumier · From: Northampton, MA

Paul Norman · From: Washington, North Carolina, USA

I AM STILL EXCITED ABOUT THE NAME OF THE SONG THEY SANG ON THE RONNIE PROPHET SHOW.

Carson Leighton · From: N.B. Canada

Doug,,I think it's Steve Smith on the Sho-Bud...I'm pretty sure he's from around the Toronto area..eh?...Carson

John Lacey · From: Black Diamond, Alberta, Canada

It's definitely Steve. Top player in Canada.

Forum Index > Pedal Steel	Goto page 1, 2 Next	Next oldest topic :: Next newest topic