| Author |
Topic: Peavey EDI Direct Box - Found one! |
Lynn Stafford
From:
Ridgefield, WA USA
|
Posted 5 Feb 2012 11:17 am |
|
I'm looking for one of these to use in my Nashville 400 amp to eliminate having to mic it. With this device wired between the speaker outbut and the speaker itself, you can just insert a mic cable and run it to the PA. I wish I haden't sold the one I used to have 
_________________
Best regards,
Lynn Stafford
STEEL GUITAR WEST
http://www.steelguitarwest.com
Steel Guitar Technician (Restoration, Set-up, Service and Repair work)
Previous Emmons Authorized Dealer & Service Technician (original factory is now closed)
ZumSteel Authorized Service Technician
----------------------------------
Last edited by Lynn Stafford on 7 Feb 2012 1:22 pm; edited 1 time in total |
|
|
 |
Don Discher
From:
Sault Ste Marie,Ontario,Canada
|
Posted 5 Feb 2012 12:54 pm edi
|
|
| I have one,make me an offer,I have no idea what I paid for it. |
|
|
|
Lynn Stafford
From:
Ridgefield, WA USA
|
Posted 5 Feb 2012 5:54 pm Peavey EDI Direct Box
|
|
Don,
Please check your email.
_________________
Best regards,
Lynn Stafford
STEEL GUITAR WEST
http://www.steelguitarwest.com
Steel Guitar Technician (Restoration, Set-up, Service and Repair work)
Previous Emmons Authorized Dealer & Service Technician (original factory is now closed)
ZumSteel Authorized Service Technician
----------------------------------
Last edited by Lynn Stafford on 6 Feb 2012 6:14 am; edited 1 time in total |
|
|
|
Charlie St Denis
From:
Ontario, Canada
|
Posted 6 Feb 2012 4:27 am
|
|
Hey Lyn
I have one for $25.00 if your still interested.
Charlie |
|
|
|
Lynn Stafford
From:
Ridgefield, WA USA
|
Posted 6 Feb 2012 6:13 am Peavey EDI Direct Box
|
|
Charlie,
Please check your email.
_________________
Best regards,
Lynn Stafford
STEEL GUITAR WEST
http://www.steelguitarwest.com
Steel Guitar Technician (Restoration, Set-up, Service and Repair work)
Previous Emmons Authorized Dealer & Service Technician (original factory is now closed)
ZumSteel Authorized Service Technician
---------------------------------- |
|
|
|
Kevin Mincke
From:
Farmington, MN (Twin Cities-South Metro) USA
|
Posted 6 Feb 2012 10:19 am Edi
|
|
| Sent you a pm Lynn...... |
|
|
|
Sam Conomo
From:
Queensland, Australia
|
Posted 6 Feb 2012 12:40 pm edi
|
|
hi forum mates,edi,what sort of signal does it give the mixer to work with.Does it avoid that thin lines in sound as if you were using a pre-amp directly in.
sam from downunder/   |
|
|
|
Lynn Stafford
From:
Ridgefield, WA USA
|
Posted 7 Feb 2012 8:32 am Edi
|
|
Sam,
Well, the signal "in theory" should be virtually the same as what you'd expect from using a low impedance mic in front of the speaker. I've had good results using these units in the past, so I thought I'd try to locate another.
_________________
Best regards,
Lynn Stafford
STEEL GUITAR WEST
http://www.steelguitarwest.com
Steel Guitar Technician (Restoration, Set-up, Service and Repair work)
Previous Emmons Authorized Dealer & Service Technician (original factory is now closed)
ZumSteel Authorized Service Technician
---------------------------------- |
|
|
|
Charlie St Denis
From:
Ontario, Canada
|
Posted 7 Feb 2012 8:48 am
|
|
Hi Lynn
Please check your email.
Thanks
Charlie |
|
|
|
Lynn Stafford
From:
Ridgefield, WA USA
|
Posted 7 Feb 2012 1:25 pm Please Close
|
|
Thanks to all that replied. I ended up finding the newer style unit (like the photos I posted) on Amazon.com of all places!
_________________
Best regards,
Lynn Stafford
STEEL GUITAR WEST
http://www.steelguitarwest.com
Steel Guitar Technician (Restoration, Set-up, Service and Repair work)
Previous Emmons Authorized Dealer & Service Technician (original factory is now closed)
ZumSteel Authorized Service Technician
---------------------------------- |
|
|
|
