| Visit Our Catalog at SteelGuitarShopper.com |

Post new topic Session 500 remote switch replacement wire?
Reply to topic
Author Topic:  Session 500 remote switch replacement wire?
Lane Gray


From:
Topeka, KS
Post  Posted 25 Dec 2011 9:27 am    
Reply with quote

I got that remote switch from Lynn Stafford (thanks, Lynn), but it didn't work.
My trusty multimeter and half-decent mind for troubleshooting quickly figured out that the bare wire has no continuity from one end to the other.
Since I run a Holy Grail anyway, I was thinking of temporarily tying the reverb wire to the bare so I can switch the fuzz and phase.
Is there a recommended wire to replace that? Phone wire would work, but probably wouldn't last.
_________________
2 pedal steels, a lapStrat, and an 8-string Dobro (and 3 ukes)
More amps than guitars, and not many effects
View user's profile Send private message Send e-mail Yahoo Messenger
Lane Gray


From:
Topeka, KS
Post  Posted 26 Dec 2011 5:43 pm    
Reply with quote

Any ideas? I know SOMEONE has to have replace the cable in the last 30 years
_________________
2 pedal steels, a lapStrat, and an 8-string Dobro (and 3 ukes)
More amps than guitars, and not many effects
View user's profile Send private message Send e-mail Yahoo Messenger
Richard Sinkler


From:
aka: Rusty Strings -- Missoula, Montana
Post  Posted 26 Dec 2011 5:48 pm    
Reply with quote

Can't you just use any good multi-conductor cable?

Most people probably haven't had to replace it because not many can carry that dude around for 30 years Laughing Whoa! Laughing
_________________
Carter D10 8p/8k, Dekley S10 3p/4k C6 setup,Regal RD40 Dobro, Recording King Professional Dobro, NV400, NV112,Ibanez Gio guitar, Epiphone SG Special (open D slide guitar) . Playing for 54 years and still counting.
View user's profile Send private message Send e-mail
Lane Gray


From:
Topeka, KS
Post  Posted 26 Dec 2011 6:15 pm    
Reply with quote

yes, any good multi conductor would. I just would not recognize a good multi conductor cable if I ran over it. Actually, that is 1 test that I could recognize a good 1 by. But I don't think lowes or radio shack would let me take samples of the cable to the parking lot for a test run.

Would any 4 wire or more from lowes do the job?
_________________
2 pedal steels, a lapStrat, and an 8-string Dobro (and 3 ukes)
More amps than guitars, and not many effects
View user's profile Send private message Send e-mail Yahoo Messenger
Darvin Willhoite


From:
Roxton, Tx. USA
Post  Posted 26 Dec 2011 8:16 pm    
Reply with quote

You're gonna need a good two conductor with shield microphone type cable. The outside diameter is around .155 I think, I'm about 500 miles from my Session 500. Look at Partsexpress.com or Jameco.com they should have what you need.
_________________
Darvin Willhoite
MSA Millennium, Legend, and Studio Pro, Reese's restored Universal Direction guitar, a restored MSA Classic SS, several amps, new and old, and a Kemper Powerhead that I am really liking. Also a Zum D10, a Mullen RP, and a restored Rose S10, named the "Blue Bird". Also, I have acquired and restored the plexiglass D10 MSA Classic that was built as a demo in the early '70s. I also have a '74 lacquer P/P, with wood necks, and a showroom condition Sho-Bud Super Pro.
View user's profile Send private message Send e-mail
Lane Gray


From:
Topeka, KS
Post  Posted 26 Dec 2011 8:25 pm    
Reply with quote

Wouldn't I need 3-conductor if I wanted to restore reverb control?
Phase, fuzz, reverb (mine has a sweet sounding tank)
_________________
2 pedal steels, a lapStrat, and an 8-string Dobro (and 3 ukes)
More amps than guitars, and not many effects
View user's profile Send private message Send e-mail Yahoo Messenger
Richard Sinkler


From:
aka: Rusty Strings -- Missoula, Montana
Post  Posted 26 Dec 2011 11:43 pm    
Reply with quote

Opening the box should let you see how many conductors the wire has. If in doubt, buy wire that has more conductors and just use what you need. Really, pretty much any cable that Parts Express has will be good cable. I'm not sure you need "the best" for that application.

I would concentrate more on buying someone to carry the Hernia 500 for you. Laughing
_________________
Carter D10 8p/8k, Dekley S10 3p/4k C6 setup,Regal RD40 Dobro, Recording King Professional Dobro, NV400, NV112,Ibanez Gio guitar, Epiphone SG Special (open D slide guitar) . Playing for 54 years and still counting.
View user's profile Send private message Send e-mail
Darvin Willhoite


From:
Roxton, Tx. USA
Post  Posted 27 Dec 2011 7:29 am    
Reply with quote

You're probably right about the number of conductors. It's been a long time since I've even looked at my remote. Most amp foot switches use two conductor with shield, but they only control two functions, I forgot about the phaser control on the 500 remote, so you would need three conductor with shield. This will make it a little tougher to find, but there is some out there somewhere available.

The problem with the existing cable is probably near the box, or the plug, so you could cut a little off at the ends and re-solder the wires to the plug and switches. As I remember, the existing cable is really long anyway. Cut off a bit and check it with your continuity tester until you get a complete circuit. Make sure you note where the wires go on the switches and plug before you de-solder them.
_________________
Darvin Willhoite
MSA Millennium, Legend, and Studio Pro, Reese's restored Universal Direction guitar, a restored MSA Classic SS, several amps, new and old, and a Kemper Powerhead that I am really liking. Also a Zum D10, a Mullen RP, and a restored Rose S10, named the "Blue Bird". Also, I have acquired and restored the plexiglass D10 MSA Classic that was built as a demo in the early '70s. I also have a '74 lacquer P/P, with wood necks, and a showroom condition Sho-Bud Super Pro.
View user's profile Send private message Send e-mail
Darvin Willhoite


From:
Roxton, Tx. USA
Post  Posted 27 Dec 2011 7:29 am    
Reply with quote

You're probably right about the number of conductors. It's been a long time since I've even looked at my remote. Most amp foot switches use two conductor with shield, but they only control two functions, I forgot about the phaser control on the 500 remote, so you would need three conductor with shield. This will make it a little tougher to find, but there is some out there somewhere available.

The problem with the existing cable is probably near the box, or the plug, so you could cut a little off at the ends and re-solder the wires to the plug and switches. As I remember, the existing cable is really long anyway. Cut off a bit and check it with your continuity tester until you get a complete circuit. Make sure you note where the wires go on the switches and plug before you de-solder them.
_________________
Darvin Willhoite
MSA Millennium, Legend, and Studio Pro, Reese's restored Universal Direction guitar, a restored MSA Classic SS, several amps, new and old, and a Kemper Powerhead that I am really liking. Also a Zum D10, a Mullen RP, and a restored Rose S10, named the "Blue Bird". Also, I have acquired and restored the plexiglass D10 MSA Classic that was built as a demo in the early '70s. I also have a '74 lacquer P/P, with wood necks, and a showroom condition Sho-Bud Super Pro.
View user's profile Send private message Send e-mail
Pit Lenz


From:
Cologne, Germany
Post  Posted 27 Dec 2011 8:21 am    
Reply with quote

In this thread from August 2000 Jack Stoner explained the wies and their functions.

Quote:
posted 20 August 2000 03:44 PM
Pin 1 is the string effect (pin 1 and ground)
Pin 2 is the phase shifter (pin 2 and ground)
Pin 3 is the reverb.
They also use the ground pin.
The remote reverb is a 10K Audio pot.
Connect one end to Pin 3, connect the other end of the pot and center (wiper) to ground.

------------------
should the cable be shielded or does it matter?

------------------
    
Yes, the original Peavey remote had shielded cable.

Guess you can also always address Mike Brown for more information...

pit
View user's profile Send private message Send e-mail
Lane Gray


From:
Topeka, KS
Post  Posted 27 Dec 2011 8:35 am    
Reply with quote

I have the schematic and a couple diagrams from Gene (Ford?) at Peavey.

I was just wondering about replacement cable. The plug end looks like it got kinked, I'll try taking a few inches from it
_________________
2 pedal steels, a lapStrat, and an 8-string Dobro (and 3 ukes)
More amps than guitars, and not many effects
View user's profile Send private message Send e-mail Yahoo Messenger
Kevin Mincke


From:
Farmington, MN (Twin Cities-South Metro) USA
Post  Posted 27 Dec 2011 9:58 am    
Reply with quote

I would cut off a few inches from the suspected bad end (normally the wires break going into the control box from getting wrapped/wound instead of coiled/looped when storing) and use an ohm meter to see if the wire has and other bad spots and just resolder it. I wouldn't think you would find the problem in the middle of the harness. As Darvin pointed out, it is quite long anyway. Maybe redo both ends and eliminate any future problems.
View user's profile Send private message Send e-mail Visit poster's website
Ronnie Sellers


From:
Seymour Tenn
Post  Posted 14 May 2023 4:49 pm     Remote switch
Reply with quote

Hey guys I've got problems with the remote switch
on my session 500.
The amp will not come on unless the remote switch cable
is pluged in.
Any ideas what would cause this.
Thanks Ronnie.
View user's profile Send private message Send e-mail
Kevin Mincke


From:
Farmington, MN (Twin Cities-South Metro) USA
Post  Posted 18 May 2023 10:17 am    
Reply with quote

I would look at the jacks as they may be shorting (grounding) when a 1/4” is not plugged in.
View user's profile Send private message Send e-mail Visit poster's website
Richard Sinkler


From:
aka: Rusty Strings -- Missoula, Montana
Post  Posted 19 May 2023 5:19 am     Re: Remote switch
Reply with quote

Ronnie Sellers wrote:
Hey guys I've got problems with the remote switch
on my session 500.
The amp will not come on unless the remote switch cable
is pluged in.
Any ideas what would cause this.
Thanks Ronnie.


You might want to start your own topic for this. There are probably several members who can help you, but have no interest is a thread on replacing the remote cable.
_________________
Carter D10 8p/8k, Dekley S10 3p/4k C6 setup,Regal RD40 Dobro, Recording King Professional Dobro, NV400, NV112,Ibanez Gio guitar, Epiphone SG Special (open D slide guitar) . Playing for 54 years and still counting.
View user's profile Send private message Send e-mail
Kevin Mincke


From:
Farmington, MN (Twin Cities-South Metro) USA
Post  Posted 19 May 2023 5:32 am    
Reply with quote

Agree Richard, I almost posted the same remarks. New topic would generate a better focused response.
View user's profile Send private message Send e-mail Visit poster's website

All times are GMT - 8 Hours
Jump to:  
Please review our Forum Rules and Policies
Our Online Catalog
Strings, CDs, instruction, and steel guitar accessories
www.SteelGuitarShopper.com

The Steel Guitar Forum
148 S. Cloverdale Blvd.
Cloverdale, CA 95425 USA

Click Here to Send a Donation

Email SteelGuitarForum@gmail.com for technical support.


BIAB Styles
Ray Price Shuffles for Band-in-a-Box
by Jim Baron