| Author |
Topic: 15" speaker in Twin Reverb Cabinet |
Mike Marchelya
From:
Denver, Colorado, USA
|
Posted 5 Apr 2003 6:42 pm |
|
| Will a 15" speaker like a JBL or Altec fit in a standard Twin Reverb cabinet? |
|
|
 |
Donny Hinson
From:
Glen Burnie, Md. U.S.A.
|
Posted 6 Apr 2003 3:04 pm
|
|
Yes, any fifteen will fit...but it's a tight fit! (I have a 15" EV-SRO in mine.) You'll have to make a new baffle, and then mount it in the cabinet. Then, lay the cabinet face-down, and figure where you're going to mount it. You'll have to place it so the the output transformer sits in one of the speaker-basket openings. Place the speaker as low in the cabinet as possible (again, to keep the cone away from the output transformer), and mark the mounting holes. Then you can remove the baffle, cut the opening for the speaker, mount it, and put the amp back together.
Note, this is much easier in an old Twin, as the baffle was held in place with screws. The later ones (with the glued-in baffle) are a pain in the @$$, but it can still be done.
Takes a lot longer, though. |
|
|
|
Danny Naccarato
From:
Burleson, Texas
|
Posted 6 Apr 2003 3:31 pm
|
|
Check the specs on the Vibrosonics. These were identical to the Twins except built for 15". Mine has the speaker offset to the left when looking at the front of the amp, and it still barely clears the x-former.
Danny |
|
|
|
Chris Erbacher
From:
Sausalito, California, USA
|
Posted 6 Apr 2003 4:27 pm
|
|
| hey mike, check with ricky davis. i posted a thread a while ago and it was in relation to amp choice, and i remember him telling me that he used a twin heavily modded, but also with a 15" speaker, which is basically a vibrosonic, but if you want the specific details of how to do it and what he uses, you might contact him, i'm sure he can give you the lowdown, take it easy and good luck with your venture. |
|
|
|
Bill Terry
From:
Bastrop, TX
|
Posted 7 Apr 2003 6:16 am
|
|
I put a 15" JBL D140 in my Twin, it will fit, but Danny and Donny are right. You have to move it over to clear the output transformer. I didn't have to align the JBL basket openings though.
|
|
|
|
Dave Van Allen
From:
Doylestown, PA , US , Earth
|
Posted 7 Apr 2003 10:29 am
|
|
whover did the retrofit on mine centered it, and the transformer is entertwined with the speaker frame. not touching but only just; I tried fitting another speaker in there and there was NO may it would go. I'll just have to stick with the JBL.. (everyone say "awwwwwww, poor baby")  |
|
|
|
jim milewski
From:
stowe, vermont
|
Posted 8 Apr 2003 6:26 am
|
|
| very important what Donny said! you have to rotate the speaker so the output transformer sits between the "spokes", I was blessed to do this to the reissue twin, the baffle board is screwed in, BW 1501, made this a great amp |
|
|
|
Joerg Hennig
From:
Bavaria, Germany
|
Posted 8 Apr 2003 9:50 am
|
|
| On the Vibrosonic, the speaker is located far to the right if you look at it from behind, or to the left seen from the front. |
|
|
|
Joe A. Camacho
|
|
|
|
Jeff Jackson
From:
Iowa, USA
|
Posted 1 Apr 2011 8:13 pm
|
|
| I have been thinking about taking my Altec 15" speaker out of my old Gretsch Nashville Pro Steel amp and putting it in my late 60's Twin Reverb. It sounds great with that amp for guitar and pedal steel. I am just hoping it will fit. |
|
|
|
David Nugent
From:
Gum Spring, Va.
|
Posted 2 Apr 2011 2:18 am
|
|
| If you have the reissue Twin, the speakers, baffleboard, and grillcloth are held with screws and can be removed as one unit. I have a 15" baffleboard and grillcloth that held both a JBL E-130, and later a 1501-4 BW, and both fit fine. You are welcome to it, just reimburse me for shipping. |
|
|
|
Ken Fox
From:
Nashville GA USA
|
Posted 2 Apr 2011 7:51 am
|
|
In the past I build six Vibroverb clones and used Twin output transformers. You can see how the speaker was rotated:
 |
|
|
|
randy barnes
From:
alexandria, MN USA
|
Posted 8 Jun 2011 5:47 pm how to replace the glued in baffle on the Fender Twin?
|
|
| I realize that it is difficult to remove the speaker baffle on a newer Twin ('82) but any ideas how to go about replacing it without destroying the entire cabinet? I would like to try putting in a 15 in my Twin Reverb. tnx guys. |
|
|
|
Clyde Mattocks
From:
Kinston, North Carolina, USA
|
Posted 8 Jun 2011 8:52 pm
|
|
I did one years ago and relocated the transformer. You have to splice on extra lengths of wire. It would be a good idea also to check the location before you fasten it down permanently to make sure you've not put it in a place to set up excessive hum. By doing it this way,I was able to keep the speaker centered. Disclaimer: Although I did it once, I don't believe I'd do it again.
_________________
LeGrande II, Nash. 112, Fender Twin Tone Master, Session 400, Harlow Dobro, R.Q.Jones Dobro |
|
|
|
Pete Burak
From:
Portland, OR USA
|
Posted 9 Jun 2011 7:58 am
|
|
I think an easier solution would be to take the speakers out of your Twin (alot easier to lift/move around, etc), and get a separate 15" cab/speaker.
You can then put the Amp right next to your steel for easy amp setting adjustments as needed, and run a cord to your speaker which you move around until you find the right placement for it within whatever the given setup is.
They also make a ring that you can use to convert a 15" baffle to 12". I got one from JaMac in Portland for 5$, and makes for easy speaker swaps once you get the holes drilled (Ring mounts to baffle with 4 holes, speaker mounts to ring with 4 holes). |
|
|
|
Scott Swartz
From:
St. Louis, MO
|
Posted 9 Jun 2011 10:55 am
|
|
I was just looking at doing this to the Twin I have, and comparing to a 73 Vibrosonic with factory JBL.
On the Vibrosonic, the outer edge of the speaker frame is located 1/8" from the cabinet bottom and 1/8" from the right cabinet upright.
In other words about as far right and low as can be reaasonably done. With this arrangement the baffle board has to be dado'ed (no room for the mounting strips used on a screwed baffle), although the speaker does not have to be rotated to clear the spokes and other speakers would fit.
_________________
Scott Swartz
Steeltronics - Steel Guitar Pickups
www.steeltronics.com |
|
|
|
