| Visit Our Catalog at SteelGuitarShopper.com |

Post new topic Emmons Lightweight Case
This topic is locked: you cannot edit posts or make replies.
Author Topic:  Emmons Lightweight Case
Tommy Dodd


From:
Acworth, Ga., USA (deceased)
Post  Posted 18 Aug 2010 7:20 am    
Reply with quote

An original Emmons factory guitar case that came with a 1968 D10 push/pull. The owner evidently didn't use it long and consequently the case is in very good condition. (Don't know why he replaced the handle but he did!) Is it substantial enough to fly your guitar in.....probably not. But, it weighs 6 - 8 pounds and will be a lot easier on your back for the "around town" gigs for sure. Price $145 plus shipping.









View user's profile Send private message Visit poster's website
Tommy Dodd


From:
Acworth, Ga., USA (deceased)
Post  Posted 19 Aug 2010 3:56 pm    
Reply with quote

I need some help from some of you Emmons experts. I have had a couple inquiries about different Emmons guitars this case might fit. Was there a difference in the cabinet sizes over the years of the P/P production. Also, how about the Legrande series. Would those cabinets be about the same in general so that someone could use this lightweight case? Thanks for your "expert" opinions.
View user's profile Send private message Visit poster's website
Mike Wheeler


From:
Delaware, Ohio, USA
Post  Posted 19 Aug 2010 5:10 pm    
Reply with quote

Tommy, the simplest thing to do is to post the inside dimensions of the case. Then everyone could determine whether their guitar would fit or not.
_________________
Best regards,
Mike
View user's profile Send private message Send e-mail
Kevin Hatton

 

From:
Buffalo, N.Y.
Post  Posted 19 Aug 2010 6:04 pm    
Reply with quote

Tommy, Push Pulls are 33" , all Legrandes are 33 1/2". Both 11" wide.
View user's profile Send private message Send e-mail Visit poster's website
Kyle Everson

 

From:
Nashville, Tennessee
Post  Posted 20 Aug 2010 10:56 pm    
Reply with quote

Some pre-1969 push-pulls were thinner than 11".
View user's profile Send private message
Tony Dingus

 

From:
Kingsport, Tennessee, USA
Post  Posted 21 Aug 2010 10:22 am    
Reply with quote

What is this case made out of ?

Tony
View user's profile Send private message Send e-mail
Willis Vanderberg


From:
Petoskey Mi
Post  Posted 21 Aug 2010 1:00 pm    
Reply with quote

All push pulls will fit this case. Even my D-10 Black Rock with a wooden pedal board will fit. The black Rock will not fit the later p/p cases as the pedal board is a bit too wide.
View user's profile Send private message Send e-mail
Ronnie Tibbitts


From:
Dallas, Georgia, USA
Post  Posted 26 Aug 2010 10:57 am    
Reply with quote

Take a ride TTT. Very Happy
View user's profile Send private message Send e-mail
Glenn Austin

 

From:
Montreal, Canada
Post  Posted 26 Aug 2010 6:12 pm    
Reply with quote

I offered to buy this case and was told it was sold. I would still like to buy it.
View user's profile Send private message Send e-mail
Tommy Dodd


From:
Acworth, Ga., USA (deceased)
Post  Posted 27 Aug 2010 1:38 pm    
Reply with quote

Guitar case is sold.
View user's profile Send private message Visit poster's website

All times are GMT - 8 Hours
Jump to:  
Please review our Forum Rules and Policies
Our Online Catalog
Strings, CDs, instruction, and steel guitar accessories
www.SteelGuitarShopper.com

The Steel Guitar Forum
148 S. Cloverdale Blvd.
Cloverdale, CA 95425 USA

Click Here to Send a Donation

Email SteelGuitarForum@gmail.com for technical support.


BIAB Styles
Ray Price Shuffles for Band-in-a-Box
by Jim Baron