| Author |
Topic: Speakon Connectors |
George Redmon
From:
Muskegon & Detroit Michigan.
|
Posted 12 Oct 2008 3:34 pm |
|
| I just purchased 4 new PA cabs, they all have only speakon jacks. All my speaker cables are 1/4". So i need to convert them to speakon. How about some EASY directions as to which wire goes where. Only using 2 conductor 12 Gauge peavey speaker cable. |
|
|
 |
Ray Minich
From:
Bradford, Pa. Frozen Tundra
|
Posted 12 Oct 2008 3:58 pm Speak-On connector
|
|
I ran in to this problem with a Crown amp I acquired several months ago.
If you go to the Crown website and (for example) find and download the manual to the likes of the CE-1000, it will give you the speak-on connector wiring for the 4-wire connector.
Don't know yet if it's safe to assume all 4 conductor are wired the same across brands, but it's a start.
http://www.iceco.com/Crown/CE1000.pdf
http://www.crownaudio.com/gen_htm/legacy/legacamp.htm |
|
|
|
William Matthews
From:
New York, USA
|
Posted 12 Oct 2008 4:33 pm
|
|
| They make adapters from 1/4" to Speakon.. Try www.mouser.com, or www.mcminone.com, or Allied Electronics.. If you are still haveing trouble, I'll send you the part numbers |
|
|
|
Jon Light
From:
Saugerties, NY
|
|
|
|
Michael Strauss
From:
Delray Beach,Florida
|
Posted 12 Oct 2008 4:59 pm
|
|
Look on Ebay, really! 
_________________
Carter S-12U, Sho-Bud LGD (80's), Fender Jazz King, Korg Pandora Toneworks PX4D, Modulus Q6, Ampeg B5R, Lapstick Travel Guitar mod to lapsteel |
|
|
|
George Redmon
From:
Muskegon & Detroit Michigan.
|
Posted 12 Oct 2008 6:21 pm
|
|
| I have seen those adapters, i would just as soon not use adapters. I loose them, step on them, they grow legs and walk away. So i am pretty handy with a solder iron, i would just as soon solder the speakon to the cable. |
|
|
|
Jim Sliff
From:
Lawndale California, USA
|
Posted 13 Oct 2008 5:04 am
|
|
This link is the one I've always used as a guide when I forget how to wire them!
http://www.crownaudio.com/pdf/amps/126986.pdf
Note - there IS no soldering with Speakons. Personally, unless I'm making cables for a house rig I'd use the adapters - that way your cables have multiple uses.
_________________
No chops, but great tone
1930's/40's Rickenbacher/Rickenbacker 6&8 string lap steels
1921 Weissenborn Style 2; Hilo&Schireson hollownecks
Appalachian, Regal & Dobro squarenecks
1959 Fender 400 9+2 B6;1960's Fender 800 3+3+2; 1948 Fender Dual-8 Professional |
|
|
|
George Redmon
From:
Muskegon & Detroit Michigan.
|
Posted 13 Oct 2008 8:43 am
|
|
| Ok...so if i'm a reading this right. I should buy the LN4FC speakon connector. And if i'm a using only a two conducter speaker cable, which i am. Then i should attach the white {+} lead to the +1 termanal, and my black ground {-} to the -1 termanal and not use +2 or -2 termanals right? I heard that the LN4FC speakon is the standard used now by most cabs and ampm companies, and the two prong speakon is not used as a standard, is this right? |
|
|
|
Bill Moore
From:
Manchester, Michigan
|
|
|
|
George Redmon
From:
Muskegon & Detroit Michigan.
|
Posted 13 Oct 2008 1:16 pm
|
|
| Hey alright, that helped. I have it now. Thank you so very very much for the info everyone. Bill that made it so simple even a feller like me could figure it out. Thanks a bunch. |
|
|
|
Mike Brown
From:
Meridian, Mississippi USA
|
Posted 13 Oct 2008 1:59 pm Speakon Cables
|
|
George, here are the Peavey cables. If you have questions, don't hesitate to contact me at 1-877-732-8391, ext. 1180. The model of speaker cabinet that you have purchased would determine the model of cable for your amplication.
Mike Brown
Peavey USA |
|
|
|
Donny Hinson
From:
Glen Burnie, Md. U.S.A.
|
Posted 16 Oct 2008 3:05 pm Re: Speakon Connectors
|
|
| George Redmon wrote: |
| I just purchased 4 new PA cabs, they all have only speakon jacks. All my speaker cables are 1/4". So i need to convert them to speakon. |
I'd pull the cabs apart, remove the klunky Speakons, and replace them with standard 1/4" jacks. I would not own a piece of gear that forced me to change my cables!!!  |
|
|
|
Jim Sliff
From:
Lawndale California, USA
|
Posted 16 Oct 2008 7:18 pm
|
|
The nice things about Speakons are that they are just about bulletproof once they are connected properly, and it's MUCH easier to use heavier-gage wire with them than even the oversized 1/4" plugs. I've also found them to give a far more positive connection at the receiving end, which are much better and heavier-duty designs that the prototypical Switchcraft 1/4" jack which isn't exactly robust in construction.
Almost all high-power bass rigs and PA systems I've worked with over the last 10 years have used Speakon-type connectors or heavy-duty banana plugs, and I daresay a lot of players would just as well find a better input system - on that end it's rarely the cord (at least for me with George L's) but I've replaced 1/4" input jacks by the hundreds over the years. It's a weak point in every amp (and worse with the cheesy plastic crap Marshall and many others are using now).
_________________
No chops, but great tone
1930's/40's Rickenbacher/Rickenbacker 6&8 string lap steels
1921 Weissenborn Style 2; Hilo&Schireson hollownecks
Appalachian, Regal & Dobro squarenecks
1959 Fender 400 9+2 B6;1960's Fender 800 3+3+2; 1948 Fender Dual-8 Professional |
|
|
|
Donny Hinson
From:
Glen Burnie, Md. U.S.A.
|
Posted 17 Oct 2008 2:56 pm
|
|
Jim...exactly. I want the plug/jack to be the weak point. With a husky plug and jack that "lock" together, you're far more likely to pull an amp or speaker cab over, or off a stand when some club-foot trips over a wire. With the ol' reliable 1/4" plug, it either breaks or it disconnects, either of which are preferable (to me) to dumping an amp or speaker cabinet on the floor.  |
|
|
|
Dave Grafe
From:
Hudson River Valley NY
|
Posted 21 Oct 2008 4:46 pm
|
|
| ...of course if the trusty (rusty?) 1/4" SHORTS OUT when it fails and thus fries your amp you will not be such a happy camper... |
|
|
|
