| Author |
Topic: Nashville 112 "Master Reverb" question |
Don Davis Jr
From:
Georgia, USA
|
Posted 5 May 2008 4:56 pm |
|
If you're basically using the Nashville 112 as a powered speaker cabinet by running another preamp, pod, etc. into the "power amp in" plug in the back, does the reverb operate or only the master volume?
Looking at the block diagram it looks like the reverb would not function when you're running into the power amp in, but I wondered why then they would call it "master"? |
|
|
 |
Donny Hinson
From:
Glen Burnie, Md. U.S.A.
|
Posted 5 May 2008 5:13 pm
|
|
| Well, the reverb is usually in the 2nd or 3rd preamp section. I've never seen one that's in the power amp. A "Master Reverb" designation normally signifies that it's working in all channels of the amp. |
|
|
|
Roger Crawford
From:
Griffin, GA USA
|
Posted 5 May 2008 5:46 pm
|
|
Don,
When you go into the power amp in on the back, the reverb will not be in the circuit. My guess on why it's labeled "master reverb" would be if you go from the pre amp out of one NV112 to another the pre amp in of another, the reverb on the Master amp would be the one to adjust for both units. Mike Brown, where are you? |
|
|
|
Roger Francis
From:
kokomo,Indiana, USA
|
Posted 6 May 2008 6:38 am
|
|
| Roger is rite, the reverb dos'nt work when using the power amp in, and as far as the "master reverb", i asume because it's the only knob that controls the reverb before it goes to the power amp. |
|
|
|
Don Davis Jr
From:
Georgia, USA
|
Posted 6 May 2008 7:22 am
|
|
Thanks for the replies, fellows.
I thought that was how it is from reading the "block diagram" online, but I'm really no good at reading those things.
Don |
|
|
|
Mike Brown
From:
Meridian, Mississippi USA
|
Posted 6 May 2008 10:52 am Reverb
|
|
| The word "master" means that the reverb will effect the complete signal. On mixers, it would mean that it is the "master" reverb control over all channels. Why the reverb control on a Nashville is labeled, "master", I do not know nor does it make a difference in that case. |
|
|
|
Delmar Horner
From:
Maryland, USA
|
Posted 6 May 2008 5:16 pm Question
|
|
I ordered a nv 112 in april when i called for ststus of the 112 they told me it was on back order and wouldnt ship untill mid june?What is going on at PEAVEY?
_________________
Have A 1971 Emmons D 10 AMPS Traynor Mark 3 PEAVEY NV 112 effects BOSS DD 3.Goodrich Model 3 A match box super sustain. |
|
|
|
Bill Ferguson
From:
Milton, FL USA
|
Posted 7 May 2008 4:00 pm
|
|
The reverb will not work if you plug in the power amp in, however, if you plug into the POST return on the front of the amp, you are in the same as power amp in, BUT, you get the Reverb.
Bill
_________________
AUTHORIZED George L's, Goodrich, Telonics and Peavey Dealer: I have 2 steels and several amps. My current rig of choice is 1993 Emmons LeGrande w/ 108 pups (Jack Strayhorn built for me), Goodrich OMNI Volume Pedal, George L's cables, Goodrich Baby Bloomer and Peavey Nashville 112. Can't get much sweeter. |
|
|
|
Don Davis Jr
From:
Georgia, USA
|
Posted 7 May 2008 4:48 pm
|
|
| Bill Ferguson wrote: |
The reverb will not work if you plug in the power amp in, however, if you plug into the POST return on the front of the amp, you are in the same as power amp in, BUT, you get the Reverb.
Bill |
Thanks for the tip, Bill, I had not thought of that!
I'm one of those guys that actually likes the NV112 reverb. |
|
|
|
