| Author |
Topic: schematic for steel driver 2 |
Jack Goodson
From:
new brockton,alabama (deceased)
|
Posted 18 Oct 2007 10:22 am |
|
| i am looking for a schematic for a steel driver 2,it has a loose wire and i need to know where it connects to. any help would be appreciated.....thanks jack |
|
|
 |
Steve Norman
From:
Seattle Washington, USA
|
Posted 18 Oct 2007 11:29 am
|
|
I dont have a schematic, but I can open mine and tell you by wire color,
_________________
GFI D10, Fender Steel King, Hilton Vpedal,BoBro, National D dobro, Marrs RGS |
|
|
|
Jack Stoner
From:
Kansas City, MO
|
Posted 18 Oct 2007 11:31 am
|
|
| Steve is about the best you are going to do unless you send it to Goodrich. They won't sell any schematics for their equipment. |
|
|
|
Jack Goodson
From:
new brockton,alabama (deceased)
|
Posted 18 Oct 2007 12:36 pm email
|
|
| Steve: I sent you an email....thanks jack |
|
|
|
Steve Norman
From:
Seattle Washington, USA
|
Posted 18 Oct 2007 1:41 pm
|
|
Is this the one? Mine doesnt look like this, Mine has driver on left side, overdrive on right.
_________________
GFI D10, Fender Steel King, Hilton Vpedal,BoBro, National D dobro, Marrs RGS |
|
|
|
Jack Goodson
From:
new brockton,alabama (deceased)
|
Posted 18 Oct 2007 2:04 pm
|
|
| steve: that looks like mine, it is the blue wire coming from the tone pot on the left side (the input end). i cannot see where it attaches in the photo.....thanks jack |
|
|
|
Steve Norman
From:
Seattle Washington, USA
|
Posted 18 Oct 2007 2:16 pm
|
|
Unfortunately I got that image
here:
http://filters.muziq.be/model/goodrich/steeldriver2
I will still look at mine and tell you where my wires go, My steel driver II looks like the new steel driver IIIs. I should be able to get back to you tomorrow after I get to my practice space.
_________________
GFI D10, Fender Steel King, Hilton Vpedal,BoBro, National D dobro, Marrs RGS |
|
|
|
Steve Norman
From:
Seattle Washington, USA
|
Posted 18 Oct 2007 2:22 pm
|
|
Looks like it attaches to the selector switch along with the wire from the right side pot. is the solder broken where the other wire attaches?
_________________
GFI D10, Fender Steel King, Hilton Vpedal,BoBro, National D dobro, Marrs RGS |
|
|
|
Jack Goodson
From:
new brockton,alabama (deceased)
|
Posted 18 Oct 2007 4:11 pm
|
|
| Steve: I connected the two blue wires on the left and right together, it works but the volume level on a 1 to 10 is putting out a level of about one...i am not sure if the other wires are connected properly , this unit belonged to a friend of mine and i dont know if he or someone else may have changed some of the wiring.that is the reason i was looking for a schematic....thanks jack |
|
|
|
Steve Norman
From:
Seattle Washington, USA
|
Posted 18 Oct 2007 4:25 pm
|
|
sounds bad,,I'll look at mine and try to draw it out for you. like its not getting to a transmiter or something. Greg Cutshaw is an electrical engineer you may wanna try him
_________________
GFI D10, Fender Steel King, Hilton Vpedal,BoBro, National D dobro, Marrs RGS |
|
|
|
